MachPower WL-APODB48-056 User manual

WIRELESS AP DUAL BAND1200MBPS
WL-APODB48-056
USER MANUAL

2REV.1216

3
Thanks
for choose our product
___________________________________________________________________
INDEX
CHAPTER 1 Hardware and Operation mode Instruction
1.1 LED indicator
1.2 AP Interface
1.3 Power Supply
1.3.1 Powered by PoE Switch
1.3.2 Connect Outdoor CPE with PCby wireless
CHAPTER 2 Login
CHAPTER 3 WEB GUI interface Setting
3.1 Status
3.2 Wizard Configuration
3.2.1 Gateway Mode
3.2.2 WiFi Repeater mode
3.2.3 WISP Operation mode
3.2.4 AP Operation mode
3.3 Advanced Setting
3.3.1 Device Status
3.3.2 2.4G Wireless Setting
3.3.3 2G Wireless Analyzer
3.3.4 Virtural AP
3.3.5 2.4G Access Control
3.3.6 2.4G Advanced Settings
3.3.7 5.8G Wireless Setting
3.3.8 Network setting
3.3.9 Management
CHAPTER 4 Share Internet & Obtain IP address automatically
CHAPTER 5 Trouble Shooting
CHAPTER 6 SMB Products

4
CHAPTER 1
HARDWARE INSTRUCTION
1.1 AP Setup
1.2 AP Interface
RST: Reset Button, it make AP revert to default data after press it 15 seconds.
WAN/PoE: Gigabit WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under Outdoor Access Point and WiFi
Repeater operation mode.
SMA Connector: have 2.4G and 5.8G, connect with 2.4G or 5.8G antenna.
CHAPTER 2
LOGIN
1. Connect the Outdoor Access Point with computer
2. Configure the PC’s local connection IP address as 192.168.188.X (X is number from 2 to 254), subnet mask is 255.255.255.0, follow netx
image to finish

5
3. Input 192.168.188.253 into IE browser, then pop up the login page, the default login user name: Admin, Passwords: admin, pls do
following next image:
CHAPTER 3
WEB GUI INTERFACE SETTING
3.1 Status
After login, then Device Status will be showed:
In this ceiling Outdoor CPE, the default operation mode is AP mode.
Then in 2.4G Wireless Setting, GUI configuration page showed as below:
User can configure the SSID, password, band width, channel here, then Apply to finish.

6
5.8G Wireless Setting GUI configuration setting showed as previus image:
LAN Setting to configure the DHCP or Fix IP

7
AP location setting: can mark where the AP set up, and AP name as next image
3.2 Wizard Configuration
Click Wizard in Status page, will pop up following page to configure the operation mode:
There are four operation mode of this ceiling Outdoor CPE, and there are explanation for each operation mode for better application
3.2.1 Gateway Mode
Click Gateway mode, will pop up following pictures:
Pls choose the right WAN setting mode, then click next to continue.

8
When click Next, then will complete the Gateway mode setting and show following picture:
When return to Status, the page showed as follow:
3.2.2 WiFi Repeater mode
Click WiFi Repeater operation mode in Wizard, then following page will pop up, and choose the right SSID to bridge, then next.

9
After click Next button, then should configure the wireless settig as follow, then click Next to finish:
Click Return button, will back to Status, show Repeater mode data, show fail or success, and user can configure this
data in this page if required.
Please note, when click wireless relay setting, following page will pop up, you can make change from here easy

10
3.2.3 WISP Operation mode
Click WISP operation mode in Wizard, then will pop up the configure page, pls set the WISP operation mode based on
the stepes showed in picture
Configure the right WAN setting in WISP operation mode, then next.
Configure wireless data showed as follow:

11
Then complete and back to status, will show the connection fail or success, then can configure the data based on request:
Remark: When click WAN Setting, will pop up following picture:
3.2.4 AP Operation mode
Set the wireless data, AP Location info as required, then click next to continue and enter into LAN setting.
After LAN setting, complete the AP mode configuration and back to Status:

12
3.3 Advanced Setting
In advanced setting, user can check the Outdoor CPE’s firmware version, working status, 2.4G wireless, 5.8G Wireless, LAN Status,
upgrade firmware, Reset...
Let’s Click Advanced Setting in status page, will show return home, Setup Wizard which we showed before.
Let’s shown mode in Device Status, 2.4G Wireless, 5.8G Wireless, Network and Management.

13
3.3.1 Device Status
In this page, mainly to check the Outdoor CPE’s status in firmware version, 2,4G Wireless, 5.8G Wireless and LAN status:
3.3.2 2.4G Wireless Setting
In this part, will show the 2.4G Basic Setting, Virtual AP, Access control and Advanced Setting:

14
3.3.3 2G Wireless Analyzer
Mainly to analyze the AP’s singal strength in some channel, to make user more easy to choose the right channel
and avoid the wifi interface.
3.3.4 Virtural AP
There are 3 virtural AP in 2.4G wireless, if need virtural SSID, then users can configure it showed in following picture:
v

15
3.3.5 2.4G Access Control
Mainly show MAC allow or deny
3.3.6 2.4G Advanced Settings
In this page, will show the regional, RF Power, Max user access.
3.3.7 5.8G Wireless Setting
Almost same as 2.4G Wireless
3.3.8 Network setting
In this page, mainly to show the LAN setting and VLAN as follow:

16
3.3.9 Management
In this part, show the system time, Logs, upgrade firmware, system, user info.
And we show System time, how to upgrade firmware and system page to users:

17
CHAPTER 4
SHARE INTERNET & OBTAIN IP ADDRESS AUTOMATICALLY
Set computer’s TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as following picture showed.
the computer will obtain the IP address from router or base station to get Internet.

18
CHAPTER 5
TROUBLE SHOOTING
The Failure phenomenon and solution
Failure phenomenon Solution
SYS Indicator off Pls make sure the PoE module connection is right. POE Port connect with AP, LAN
port connect with computer
Can’t land to Outdoor CPE through Web
page
Pls check the IP address of computer and Outdoor CPE to see whether they are in
same networking segment, The method is click “start”-“Run” input“cmd”; ping
192.168.188.253 to test the Outdoor CPE connectivity.
Reset Outdoor CPE and load it again;
Pls make sure the IP address 192.168.188.253 is not occupied by other device in Out-
door CPE’s networking;
Check computer and cable problem, recommend to use 10/100M UTP unshielded
cable;
Clean up Arp binding from “Start”-“Run” input“cmd” arp –d
Clean the IE Brower’s temporary files and Cache file;
Outdoor CPE can’t connect with AP
(the status display unconnected)
Try to scan the avaliable wireless networking again;Make sure the Outdoor CPE’s wi-
reless standard (11b/g/n, 2.4G)is correct;
The Security and passwords are matched between Outdoor CPE and AP;
The signal strength of AP is too weak to connect, should be more than -75dBm;
Can’t scan the Outdoor CPE
Scan it several times more;
Make sure there are 5G signal existed.
Reset the Outdoor CPE, scan it again after Outdoor CPE restart;
The connection of Outdoor CPE and AP
is success, but the computer can’t share
internet
Pls Check the computer’s IP address and DNS setting. If it is dynamin, set the network
card as automatically obtain. If it is static IP, pls contact with ISP for correct IP address
and DNS address.
How to Reset Outdoor CPE Press the “Reset” button more than 15 seconds after power on. The Outdoor CPE will
restore factory default after the Outdoor CPE restart.

CHAPTER 6
SMB PRODUCTS
WL-AC5250-047
NETWORK CONTROLLER
PER WIRELESS AP
SUPPORTA E GESTISCE
FINO A 200 AP
WL-ICDBG48-050
IN CEILING DUAL BAND
ACCESS POINT/ROUTER
5GHz / 2.4GHz
1200Mbps
WL-CPEDB48-055
OUTDOOR WIRELESS POE48V
ACCESS POINT DUAL BAND
5GHz / 2.4GHz
1200Mbps
WL-ICDBG24-051
IN CEILING DUAL BAND
ACCESS POINT
5GHz / 2.4GHz
750Mbps
WL-APODB48-056
OUTDOOR WIRELESS POE48V
ACCESS POINT DUAL BAND
5GHz / 2.4GHz
1200Mbps
WL-ICNAP48-052
IN CEILING
ACCESS POINT
2.4GHz
300Mbps
WL-CPE5G48-058
OUTDOOR WIRELESS
CPE/ACCESS POINT
5GHz
300Mbps
WL-ICNAP24-053
IN CEILING
ACCESS POINT
2.4GHz
300Mbps
WL-CPE5G24-059
OUTDOOR WIRELESS
CPE/ACCESS POINT
5GHz
450Mbps
WL-IWNAP24-054
ACCESS POINT
2.4GHz
300Mbps
WL-ICNAP48F-060
IN CEILING
ACCESS POINT
2.4GHz
300Mbps
19

20
Mach Power ® is a registered trademark
All Rights Reserved
> visit our website www.machpower.it