Magnaflux ZB-12 UV365 User manual

Handheld On Belt
On Head
On Hard Hat
(hard hat not
included)
2 Battery Packs &
Canvas Battery Bag
for Belt Mounting
Wall Adapter
with U.S. Plug
Lamp Head Battery
Charger
Head/
Hard Hat Mount
Cigarette Lighter
Adapter
Extension
Cord
INSTRUCTIONS
us e i t 4 d i f f e r e n t w a y s
Zb-12 s y s t e m (p a r t n o . 623066) i n c l u d e s

t o s t a r t t h e l a m p
Turn the switch to the on position. Warning: this lamp
needs about 20 seconds warm up time when it is switched
on. During this time, it will flicker. This is normal. Do not
turn the switch rapidly on and off as this may damage the
bulb and ballast. The battery has an LED battery charge
indicator: GREEN = full charge; AMBER = half charge;
RED = dead battery.
1
2
3 4 5
Use the two 1" X 1" square mating pieces of industrial stick-on Velcro1. ®provided.
Stick one piece in the center back side of the hard hat and the other half on the strap where the2.
top and side strap meet, as in Photo 1 above.
Press them together as in Photo 2.3.
Place a piece of Velcro4. ®on the front center of the hard hat 1" up from the bill and the other half of
the Velcro®on the bottom center of the ZB-12 mounting base, as in Photo 3.
Press the light mounting base to the hard hat, as in Photo 4.5.
The completed installation on the hard hat is shown in Photo 5.6.
Loosen screw and nut on
battery pack and mount
onto headband using
same screw and nut.
h a r d h a t i n s t a l l a t i o n i n s t r u c t i o n s
t o a t t a c h l i g h t t o h e a d b a n d
INSTRUCTIONS

t o c h a r g e t h e l i g h t u s i n g t h e
110 v o l t s s o c k e t
Disconnect the head light from the battery pack.1.
Connect the battery pack to the battery charger.2.
Plug the one end of the 110 volt adapter into the battery charger and then the3.
other end into the wall socket.
Turn the battery switch from off to on. This will cause the battery charger LED to4.
go from green to red (if the battery is discharged).
As the battery charges, the battery charger LED will change from red to amber
to green.
When the battery charger LED turns to green, the battery is fully charged.5.
Disconnect the various cords and plugs and turn the battery pack off.6.
t o c h a r g e t h e l i g h t u s i n g
t h e 12 v o l t s c i g a r e t t e l i g h t e r p l u g :
Follow the same steps above except for step 3. Step 3 for in-vehicle charging: Plug
the one end of the cigarette lighter adapter into the battery charger and then the
other end into the cigarette lighter plug.
Keep switch
on while
charging
For AC INPUT 100v~240v:
For DC INPUT 12v~27v:
AC
100V~240V
AC
12V~27V
Wall
Adapter
Cigarette Lighter
Adapter
Battery
Charger
Battery
Charger
Battery Charger LED Status
GREEN light on: the charger is plug-in or finished charging
RED light on: Charging
ca u t i o n
DO NOT open this lighting equipment as it generates high voltage during operation.
DO NOT touch the front glass or area near the glass after the light is turned on as it
gets extremely hot.
INSTRUCTIONS

b u l b r e p l a c e m e n t :
Only replace the bulb when the lamp has not been in operation for at least an hour and the bulb
assembly is no longer hot to the touch. Unscrew the two halves of the head light at about the
mid-point. Remove the bulb assembly by gripping the outer edge of the reflector and pulling
directly ahead in the direction of the bulb. Preferably hold the replacement bulb on the outside
of the reflector with a clean rubber glove or with a clean cloth. Be sure to insert the bulb into the
socket carefully so as not to damage any pins. Do not touch the bulb or the inside of the reflector
with your hands as this may deposit skin oils and damage the performance of the lamp.
INSTRUCTIONS
Line up 2 lugs
with slots in
socket to
properly insert
bulb
3624 West Lake Avenue
Glenview, Illinois 60026
1-847-657-5300 Fax:[phone]
www.magnaflux.com
Zb-12 r e p l a c e m e n t p a r t sl e n s r e p l a c e m e n t
Unscrew the Lens Replacement Bezel
from the lamp head.
Screw in the new Lamp Replacement Bezel.
Replacement Bulb
P/N 623469
Battery Charger
P/N 623471 Battery Pack
P/N 623470
Lens Replacement Bezel
P/N 623478
Zb-12 te c h n i c a l
sp e c i f i c a t i o n s
Electrical Requirements—Charger:•
110v – 240v
Typical UV Intensity @ 15” (38 cm):•
Exceeds 1000 microwatts/cm2
Typical White Light emission:•
Less than 2 Foot-Candles