Magnum 520 User manual

Tools needed: #2 & #3 Phillips head screwdrivers, 1/2” socket or wrench.
IMPORTANT! Start all screws BY HAND when assembling your shear. This will help avoid cross-threading.
1. AT TACH R AILS 2. AT TACH TAIL
Quick Start Guide
for Magnum Shear Model #520
for Magnum Shear Model #526
(1) Power Assembly
(1) Handle Assembly
(1) Angle Guide
(1) Table
(1) Power Assembly
(1) Handle Assembly
(1) Angle Guide
(1) Table
The Hardware Kit is used in multiple models. Your Shear may not use all of the items listed.
The Hardware Kit is used in multiple models. Your Shear may not use all of the items listed.
(1) Tail
(2) Rails
(1) Hone Stone
(1) Hardware Kit
(1) Tail
(4) Rails
(1) Hone Stone
(1) Hardware Kit
In the Box:
In the Box:
In the Hardware Kit:
In the Hardware Kit:
Attach rails to Power Assembly base using
Item A screws, fitted with Item B star washers.
Attach tail to rails using Item C screws.
Make sure holes in tail are facing up.
ASSEMBLING YOUR SHEAR
Item A. (4) 6mm x 65mm PH Phillips Machine Screws
Item B. (4) M6 Star Washers
Item C. (6) 6mm x 25mm PH Phillips Machine Screws
Item D. (5) M6 x 16mm FH Phillips Machine Screws
Item A. (8) 6mm x 65mm PH Phillips Machine Screws
Item B. (8) M6 Star Washers
Item C. (8) 6mm x 25mm PH Phillips Machine Screws
Item D. (6) M6 x 16mm FH Phillips Machine Screws
Item E. (4) #10 x 1 FH Phillips Self Tapping Screws
Item F. (2) M8 x 50mm Hex Bolts
Item G. (1) M6 Thumbscrew (installed)
Item E. (4) #10 x 1 FH Phillips Self Tapping Screws
Item F. (2) M8 x 50mm Hex Bolts
Item G. (1) M6 Thumbscrew (installed)
Power Assembly
12
Tail
Model
520
Model
526
12
Power Assembly
Tail

CUT GUIDE
Maximum Thickness 520 = 7/16”
Maximum Thickness 526 = 1”
Carpet Tile
Luxury Vinyl Tile
Commercial Vinyl Tile
VCT
Parquet
PVC Tile
Rubber Tile
Soft Plastic
For manuals, registration,
warranty info, accessories,
& tips on using and
maintaining your
Magnum Shear, go to
BulletTools.com
or scan the QR code ->
PRT-INS-QRCT REV.A.6.15 ©2015 Bullet Tools Hayden, ID USA • 208-772-0175
SET UP
MAKING CUTS
3. AT TACH TAB LE
A. Attach front of table to base,
using Item D screws. Tighten
with #3 Phillips.
B. Attach back of table to tail using
Item E self tapping screws.
Tighten with #2 Phillips.
3
4
3B
3A
Item E
Item F
Tail
Item G
5
4. TO ATTACH HANDLE:
Insert Item F bolts and tighten with 1/2”
(13mm) wrench.
5. ATTACH ANGLE GUIDE
Install angle guide and tighten Item G
thumbscrew.
While gently pushing
handle down, pull Safety
Lock pin out, lift handle.
Pull Safety Lock pin
1
HANDLE UNDER
EXTREME PRESSURE
DO NOT ALLOW TO
SLAM BACK!
Place product on table.
Bring handle down until
blade touches material.
Push the handle down until
the material is completely cut.
3
2