Magtek DynaProx User manual

Stand Contents:
Stand Body: The body of the stand. Angled for better ergonomics.
Cable Channel: Allows the cable to be channeled out the back of the stand body.
(4) M4 Screws: Attaches the stand body to the DynaProx device
(2) Flat-head Screws: Attaches the base plate to the stand body.
Base Plate: Bottom of stand, can attach the stand to counter tops.
Installation of DynaProx Stand
1. Place the DynaProx face down on a clean soft surface to avoid scratching
the front face of the device. Using minimal toque, use (4) M4 screws to
attach the stand to the body.
2. Insert the cable and connect securely to the DynaProx device. Clip the
cable securely into the cable management hooks. Channel the cable outside
the back end of the stand body.
3. Align the assembly base plate and using the (2) at-head screws, screw
the base plate to the stand body.
Overview
DynaProx and DynaProx BCR deliver the next generation in touchless
payment acceptance. Both models come standard with contactless EMV
and near eld communication (NFC) technology. DynaProx can be purchased
with either a gasket for stable installation for OEMs and payment solutions;
or with a countertop, angled stand for stable acceptance at the counter top.
Major Components
DynaProx and DynaProx BCR Stand
NFC Contactless Module and Mounting Stand
Quick Installation Guide
Assembly
MagTek® Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
DynaProx (shown here) Major Components - Assembled to Stand
DynaProx (shown here) Major Components - Upside Down Blow Out

Securing DynaProx Stand to Surface
Follow Steps 1 through 2, then -
a. Place baseplate on the location where you want to secure the device.
Trace the baseplate and mark the two screw set locations (Drawn Outline).
Remove the baseplate and drill down through the surface, checking to make
certain everything is clear beneath.
b. Attach the baseplate to the stand body following step 3. Then align on the
surface to the tracing.
c. Using (2) M4 x 0.7mm thread pitch (not included) screws, screw up
through the pre-drilled holes to the baseplate. Screws should be long
enough to go through the surface and no more than 0.25” into the stand
body.
Disassembly
Repeat assembly in reverse order to remove device from counter installation
and stand.
4. Assembly is complete.
Additionally, you can secure the base plate to almost any surface using (2)
additional screws, not included.
Dimensions
Ensure to provide ample space for easy access.
PN Description
21078040 KIT, STAND, COUNTERTOP, DYNAPROX
21078043 DYNAPROX, PCI, BLACK, USB AND RS-232, WITH
STAND
21078044 DYNAPROX, PCI, BCR, BLACK, USB AND RS-232,
WITH STAND
EMV® is a registered trademark in the U.S. and other countries and an unregistered trademark elsewhere. The EMV trademark is owned by EMVCo, LLC. The Contactless Indicator mark, consisting of four graduating arcs, is a trademark owned by and used with
permission of EMVCo, LLC.
MAGTEK: Registered to ISO 9001:2015 © Copyright 2022 MagTek, Inc. PN D998200511 rev. 10 2/22
MagTek® Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
A
SHEET 1 OF 1
DESIGNED BY
DO NOT SCALE DRAWING
DRAWN BY
TOLERANCE:
TITLE:
B
SIZE
PROPRIETARY AND CONFIDENTIAL
FINISH:
4.00 x 2.8265”
DWG REV :
CHECKED BY:
DATE
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MAGTEK. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF MAGTEK IS PROHIBITED.
SCALE: 1:1
MUST BE ROHS COMPLIANT, SEE
EUROPEAN DIRECTIVE 2002/95/EC
DIM UNITS:
DWG NO.
MATERIAL:
PART NO.
1/10/2022
R.Robinson
R.Robinson
DynaProx & DynaProx BCR
EMV and NFC Contactless
DynaProx STORAGE NOTICE
TEMPERATURE: -30°C to +85°C (-22°F to 185°F)
HUMIDITY: 90% RH non-condensing
DynaProx BCR STORAGE NOTICE
TEMPERATURE: -40°C to +70°C (-40°F to 158°F)
HUMIDITY: 5 - 95% non-condensing
See product label for part number and description.
In-house Zebra label
PN 99600120
LABEL, STORAGE NOTICE, DYNAPROX
AND DYNAPROX BCR
1000008550
D100006015
B0
Assembly (continued), Installation, and Disassembly