MAGUIRE Weigh Scale Blender 4088 TSC Owner's manual

MAGUIRE PRODUCTS INC.
Weigh Scale Blender 4088 TSC
MAGUIRE
WEIGH SCALE BLENDER
4088 Touch Screen Controller
FLEXBUS Lite
Receiver Control System
INSTALLATION  OPERATION  MAINTENANCE
Original Instructions Manual
Revision Date:
F
ebruary
2
4
, 20
20
Copyright  Maguire Products, Inc. 2020

2
Use this space to record information about your Maguire Weigh Scale Blenders:
Serial Number
Date of
Purchase
Model Number
ID
IP Address
Notes:

3
Maguire Weigh Scale Blender
This document is the Original Instructions manual of the Maguire Weigh Scale Blender models WSB-
MB, WSB-100 Series, WSB-200 Series, WSB-400 Series, WSB-900 Series, WSB-1800 Series,
WSB-2400 Series and WSB-3000 Series equipped with the 4088 Touchscreen controller.
Copyright  2020 Maguire Products Inc.
The information contained within this manual including any translations thereof, is the property of
Maguire Products Inc. and may not be reproduced, or transmitted in any form or by any means
without the express written consent of Maguire Products Inc.
To every person concerned with use and maintenance of the Maguire WSB it is recommended to
read thoroughly these operating instructions. Maguire Products Inc. accepts no responsibility or
liability for damage or malfunction of the equipment arising from non-observance of these operating
instructions.
To avoid errors and to ensure trouble-free operation, it is essential that these operating instructions
are read and understood by all personnel who are to use the equipment.
Should you have problems or difficulties with the equipment, please contact Maguire Products Inc. or
your local Maguire distributor.
Manufacturer’s Contact Information
Maguire Products Inc.
11 Crozerville Road
Aston, PA. 19014
Phone: [phone]
Fax: [phone]
Website: http://www.maguire.com
Email: [e-mail]

4
Introduction
EC Declaration of Conformity ______________________________________ 6
Getting Started – Read this page! ___________________________________ 7
Safety Notifications and Safety Hazards______________________________ 8
Blender Parts Key _______________________________________________ 10
Controller Parts Key _____________________________________________ 19
Touchscreen Overview __________________________________________ 20
Flexbus Lite Integrated Loading System
Flexbus Lite Table of Contents and Overview _______________________ 122
Flexbus Lite Setup and Configuration _____________________________ 123
Blender Setup and Installation
Assembly and Installation Instruction ______________________________ 12
Wiring Considerations ___________________________________________ 16
Selecting the Correct Model _______________________________________ 17
Touchscreen Controller Parts Key ________________________________ 19
Setting the Modes of Operation ___________________________________ 24
Enabling Hopper Types __________________________________________ 25
Example of Making Settings ______________________________________ 26
Entering Component Settings ____________________________________ 28
Setup Menu – Brief Explanation ___________________________________ 51
Check Out Procedure and Diagnostics ______________________________ 29
Dispense Station _______________________________________________ 45
Operator Access ________________________________________________ 46
Change Passwords ______________________________________________ 47
Communications ________________________________________________ 48
Automated Control ______________________________________________ 50
Blender Operation
Load Cell Calibration ____________________________________________ 32
Material Flow Rate Calibration _____________________________________ 33
Micro Pulse Instructions _________________________________________ 34
Regrind Control _________________________________________________ 35
Instructions for Normal Operation _________________________________ 39
Specialized Operations __________________________________________ 41
Menu Map – Full Explanation _____________________________________ 53
Parameters Introduction__________________________________________ 54

5
Navigating Parameters ___________________________________________ 54
Parameters – General – Explanation _______________________________ 56
Parameters – Component – Explanation ____________________________ 60
Parameter Default Settings _______________________________________ 62
Saving Parameters ______________________________________________ 64
Monitoring System Accuracy ______________________________________ 73
Cycle Printout Information ________________________________________ 73
Interpreting the Cycle Printout ____________________________________ 74
Troubleshooting with the Printout _________________________________ 75
Parameter Settings Printout _______________________________________ 79
Load Cell Calibration ____________________________________________ 32
Load Cell Recalibration – ZERO / FULL Calibration ___________________ 68
Material Usage Printout __________________________________________ 81
Blender Troubleshooting and Maintenance
Troubleshooting - What To Do _____________________________________ 82
Alarms - Cause and Solution _____________________________________ 82
Typical Problems _______________________________________________ 86
Mix Problems ___________________________________________________ 88
Increasing Throughput ___________________________________________ 90
Normal Operating Sequence ______________________________________ 91
Verifying Load Cell Function _____________________________________ 93
Load Cell Raw Signal Readout ____________________________________ 94
Backup, Restore, Factory Reset ___________________________________ 95
Updating Controller Firmware ____________________________________ 96
Hardware Maintenance ___________________________________________ 97
Blender Preventative Maintenance _________________________________ 97
17 pin Amphenol Connector Pin Assignments _______________________ 99
Technical Drawings, Electrical Diagrams, Pneumatic Diagrams ________ 100
Dimensions and Weight by Model _________________________________ 121
Decommissioning and Disposal __________________________________ 141
Disclaimers ___________________________________________________ 141
Accuracy of this Manual _________________________________________ 141
Warranty _____________________________________________________ 142
Technical Support and Contact Information ________________________ 143

6

7
Getting Started – Important!
Safety Notifications and
Safety Hazards
Page: 8 HAZARDS exist on this unit.
Read Safety Notifications and Safety Hazards.
Blender Part Identification Page: 10 Identifying key parts and what they do.
Assembly and Installation
Instructions
Page: 12 Assembly and installation instructions.
Wiring Considerations Page: 16 How to minimize electrical interference.
Model Selection Page: 17 How to verify and change your model selection. All new
blender controllers are pre-configured with the model from
factory. New, spare or swapped controllers may require a
model change.
Touchscreen Key Parts Page: 19 Identifying the key parts of the blender controller.
Touchscreen Overview Page: 20 Understanding the Touchscreen home screen.
Mode of Operation Page: 24 This section selects the general Operating Mode of the
machine (Blender, Dispenser, Totalizer) and sets the Blend
Mode as: Additive are dispensed as a % of Natural or
Materials are a % of Total Batch.
Enable / Disable
Material Type Outputs
Page: 25 To "Enable" a component, the TYPE must be selected as:
REGRIND, NATURAL, or ADDITIVE. Each TYPE is
controlled differently by the MATH routines. The controller
must know the material TYPE to know how to dispense the
setting. This is IMPORTANT. Be SURE you
UNDERSTAND this section and Mode of Operation before
operating the blender.
Check Out Procedure Page: 29 Step by step procedure to verify correct assembly.
Load Cell Calibration Page: 32 Load Cells of new blenders are calibrated at the factory.
However shipping or rough handling can create load cell
problems. If weight readings are not correct, you MUST
recalibrate the load cells.
Material Flow Rate
Calibration
Page: 33 A flow rate calibration is not necessary because the
blender will learn the flow rate over time however if you
change equipment or material you may want to re-calibrate
the material flow rate.
Normal Operation &
Saving the Configuration
Page: 39 How to start the blender and save / restore the
configuration.

8
Safety Notifications
Electrical lockout points.
Disconnect electric before opening or servicing. Use
Power Lockout Tagout.
Pneumatic lockout points.
Disconnect compressed air supply before opening or
servicing. Use Air Lockout Tagout.
CAUTION - Always wear safety glasses when using this
equipment.
SAFETY INTERLOCK SWITCH
The ACCESS DOOR is equipped with a safety interlock
switch that prevents the mix motor from running and the slide
valves from opening. DO NOT d
isable
or bypass
safety switch.
HOPPER FINGER GUARDS
Finger Guards are fitted into each Material Hopper compartment.
DO NOT reach through these Guards.
DO NOT use fingers to clear an obstruction below these guards.
DO NOT remove these Guards.
HAZARD - AUTOMATIC STARTUP
WARNING - Blender may start automatically without warning.
Maximum continuous noise level - The highest continuous Noise levels
recorded for this equipment was measured at 71.4 db.

9
Safety Hazards
HAZARD - ROTATING MIX BLADE
Mix Blades are driven with substantial Torque.
Never place your hand in the Mix Chamber while the blades
are rotating. SERIOUS INJURY WILL RESULT
HAZARD - SHARP MIX BLADES
Over time, Mix Blades may become RAZOR SHARP.
ALWAYS be careful when TOUCHING or CLEANING these
blades. Check for Sharp Edges frequently.
Replace Blades if a Hazard exists.
HAZARD - SLIDE VALVES
Slide valves in hoppers SLAM CLOSED without warning.
ALWAYS keep fingers clear of slide gate openings.
NEVER use your fingers to clear an obstruction.
NEVER use your fingers to move a sticking slide gate.
HAZARD - ELECTRICAL
Only qualified electrical technicians should make electrical
connections. Disconnect and lockout power supply before
servicing Blender.
HAZARD - ROTATING SHAFT
Auger Feeders contain a rotating shaft.
ALWAYS keep fingers clear of rotating shaft and auger.
NEVER use your fingers to clear an obstruction.
NEVER
touch a rotating shaft or auger
.
HAZARD - FALLING OBJECTS
Do Not open hopper access door if material level is above
hopper cleanout door.

10
Blender Parts Key

11
1. Auger Feeder – Screw Feeder for feeding in small percentage materials such as Colors and Additives
2. Fixed Material Hopper – Material Hopper for main materials to be dosed by the slide gates
3. Removable Hopper – Removable Material hopper for small percentage materials such as Colors and
Additives
4. Hopper Access Door – Door to access inside of hopper for quick cleaning and materials changes
5. Sight Glass – Means to view current material level inside the hopper
6. Vertical Valve – Dispense Device mounted inside removable hopper for small percentages up to 10%
7. Slide Gate – Dispense Device mounted below fixed hoppers to dispense large percentages
8. Auger Screw – Dispense Device mounted inside removable hopper for small percentages up to 10%
9. Controller – Central Controller for all settings on the blender
10. Air Assembly & Solenoids – Pneumatic assembly for activating pneumatic parts automatically and manually
11. Cleaning Airline – Airline for quick and easy cleaning of blender during materials changes
12. Load Cells – Load Cells monitor continuously the weight in the Weigh Bin
13. Load Cell Bracket – Load Cell Bracket for mounting Weigh Bin onto the Load Cells
14. Safety Interlock – Pneumatic and Electrical Safety interlock – stops blender operating if door is opened
15. Weigh Bin – Weigh Bin holds materials as materials are dispensed during a batch and weighed
16. Dump Valve – Pneumatic Valve and Flap to release materials from Weigh Bin when a batch is complete
17. Mix Chamber – Area where materials are blended together after being weighed
18. Mix Blades – Removable Mix Blades to fold the materials together to achieve an effective blend
19. Power and Circuitry Box – Central box for power and support circuitry for controller.
20. Mix Chamber Insert – Stainless Steel removable insert to assist in quick materials cleaning and changes
21. Level Sensor – Sensor to monitor material level in the Mix Chamber, pauses blender when covered and mix
chamber is full, once uncovered signals Controller to begin a new batch of material.
22. Mix Motor – Electric Motor to drive Mix Blades – Note on WSB MB and WSB 100 Series blenders this
motor is a pneumatic Mix Motor
23. Flow Control Valve – (Optional) – Additional pneumatic slide gate with finger guards to be used when
blender is not mounted directly on the throat of a machine but instead a stand or surge hopper. The Flow
Control Valve ensures material remains inside the Mix Chamber long enough to be mixed efficiently.
Automatically controlled by the blender Controller.

12
Setup and Installation
Blender Assembly and Installation Instructions
CAUTION: LOAD CELLS ARE EASILY DAMAGED.
If the FRAME is dropped from TWO FEET, the load cells WILL BE DAMAGED.
THE WARRANTY DOES NOT COVER DAMAGED LOAD CELLS.
The following items have been shipped to you:
1. FRAME and HOPPER assembly: (bolted to skid)
2. CONTROLLER BOX: with the instruction manual.
3. FEEDER BOX: contains a COLOR or ADDITIVE feeder: optional.
4. FLOW CONTROL ASSEMBLY: optional
5. FLOOR STAND or VACUUM TAKEOFF ASSEMBLY: optional
RED INSTRUCTION STICKERS will assist you during assembly.
LIFT HANGERS are available to allow lifting the blender with a strap or chain. Contact Maguire if
you require them. Weight of each model is listed on page: 121.
1A. If your unit is to be MACHINE mounted:
For WSB MB, 100, 200, and 400 series models:
Two ways to do this are suggested ON THE NEXT PAGE:
The LEFT diagram shows the FRAME and SLIDE GATE both drilled with the proper bolt pattern for your
machine and THROUGH BOLTED to your press.
The RIGHT diagram shows only the 10 x 10 steel slide-gate plate drilled for your bolt pattern and bolted to
your press. The FRAME is then bolted to it using the existing 8 x 8 inch bolt pattern holes and bolts
provided. With this method, bolt head clearance holes are required in the poly-pro slide gate plate. This
mounting works well on smaller machines.
For WSB 900 and 1800 series models:
An additional machine mount adaptor plate may be required. If you have ANY DOUBT about the
STABILITY of the unit when bolted directly to your machine throat, please call us for advice.
NOTE: When choosing proper orientation, be sure to retain access to the
controller and weigh chamber, clearance for hinged doors, and access to
removable feeder hoppers.
1B. If your unit is STAND mounted:
A stand is provided and your unit will bolt directly to it. An assembly DIAGRAM is provided on the
following pages.
An air operated FLOW CONTROL ASSEMBLY is provided for dispensing into a container. The purpose
of this unit is to allow time for mixing to occur after each dispense. This flow valve keeps the mix chamber
full to just below the sensor. This assembly bolts directly to the bottom of the Weigh Scale Blender frame.

13

14
"Vacuum Takeoff Assmbly"
With Optional VTA
WSB STANDS
37-1/4 [946]
51-1/4 [1302]
Barrel VTA WSB 100/200/400
10-1/8 [257]
A B DC
25-7/8 [657]36 [914]
39-7/8 [1012]
8-1/8 [206]
E F
Gaylord WSB 900/1800
51-7/8 [1318]63-1/4 [1607] 56 [1422]
VTA Barrel Gaylord
36 [914] 8 [203]
8 [203]
43-1/4 [1099] 69-1/4 [1759] 57-1/4 [1454]
16-1/8 [410] 36 [914]
56 [1422]
36 [914]
15 [381] 15 [381] 15 [381]
STAND DIMENSIONS
NOTE:
WSB 100/200/400 VTA Stand shown to scale.
10-1/8 [257] 10-1/8 [257]
8 [203]
8-1/8 [206] 8-1/8 [206]
14-1/8 [359] 14-1/8 [359] 14-1/8 [359]51-7/8 [1318]
39-7/8 [1012]
25-7/8 [657]
16-1/8 [410] 16-1/8 [410]

15
2. Slide the WEIGH BIN into position. It rests behind the clear-hinged access window.
On models 100, 200, and 400 install weigh bin with the air cylinder to the left. On
models 900, 1800, 2400 and 3000 install weigh bin with the air cylinder towards you.
On Micro Blenders, install the weigh bin with the load cell hanger to the left. If bin is
already in place, remove any shipping materials, packing tape or string.
3. Hang the Color and Additive Feeders: (Optional)
a. Lift side latches and fully extend slide assembly. Remove the hopper. Leave slide
extended.
b. Tilting the entire slide assembly, motor end up, insert one corner of hanger cross bar behind
frame corner post.
c. Rotate assembly into place so both ends of cross bar are behind corner posts.
d. Lower into place, bottom edge resting on frame and cross bar properly positioned behind
corner posts.
e. Re-install hopper. Slide motor forward until latches engage.
4. Place the controller on the support tray and plug in all cords:
a. Air solenoid 17 pin plug into the matching receptacle.
b. Auger feeder drive motors into duplex receptacle.
c. Mixer motor into right side of controller.
d. Sensor cord plug into front side of controller.
e. Load Cell plug into port on left side of controller.
5. Plug the CONTROLLER into the receptacle located under the controller tray.
IMPORTANT: Do NOT plug the controller into a separate
power source. The controller ground path MUST be the
same as the blender frame ground path. If your system has
the controller located in a remote location, MAKE CERTAIN
that the power to the controller comes from the receptacle
mounted on the Blender frame.
6. Connect main power to a properly fused disconnect. Main power comes from the
power box and plugs into a 110-volt or 220 volt power source. This power cable
MUST provide the ONLY power source for the entire system, including the controller.
See: WIRING CONSIDERATIONS, next page. 1800, 2400, 3000 Series Blenders
require a 240-volt power source for the mix motors. Secure voltage supply cable
per the requirements of EN 60204-1, Clause 13.4.2.
7. Connect Compressed Air to the unit. About 5.5 bar (80 psi) is recommended for
most models. 4.1 bar (60 psi) is recommended for: Micro Blender, 140R, 240R and
440R). Lubricated air is NOT recommended. Air provided to the blender should be
clean and dry. The coalescing filter is a final attempt to dry the air to protect the valves
from moisture contamination.
NOTE: Micro Blenders should be set to 4.1 bar (60 psi). The Vertical
Valves used in removable hoppers on Micro Blenders are more
accurate at the lower 4.1 bar (60 psi) pressure setting.
8. Remove all protective paper from the plastic windows.

16
Wiring Considerations
The wiring of your blender is very important to its proper operation. Electronics are very
susceptible to voltage spikes, static discharges and electromagnetic fields, all of which are very
common in plastics factories. To MINIMIZE these things, consider the following.
 The power supply should be a reliable, steady supply, not limited by a "just adequate"
control transformer. A source of voltage that comes from a large transformer that supplies
a large portion of the plant is better than a small power supply transformer that is intended
to supply only this device. Power supplies, even though they may be "isolation"
transformers, will still pass all voltage spikes right through. Their small size limits their
ability to dampen RF (Radio Frequency) noise that is often induced into the system from
outside sources. This proves worse than connection to larger central transformers.
 Avoid running the power supply line next to any heavy power lines. An unshielded power
supply in a raceway next to other heavy power lines will pick up induced RF noise and
transfer it into the WSB steel enclosure causing computer trouble.
 Long extension cords should be avoided. They also reduce the ability to provide a
dampening effect on spikes and static. The further the equipment is from a substantial
power source, the more susceptible it is to spikes.
 The CONTROLLER and the WSB frame MUST share the same GROUND PATH. This is
why you MUST plug the controller into the OUTLET that is provided ON THE FRAME.
 REMOTE SYSTEMS. If you have your controller mounted in a remote location, you will
have a number of power and signal cords running between the frame and the controller.
Remote touchscreens will have a single cable running back to the blender. BE SURE that
the LOW VOLTAGE lines are NOT BUNDLED to the HIGH VOLTAGE lines and keep them
away from other nearby electrical lines.
LOW VOLTAGE lines are: Load Cell cable, Level Sensor cord,
Air Solenoid cable, and Printer and communication cables.
HIGH VOLTAGE lines are: Mixer motor cable, Feeder motors,
and MAIN POWER line.
Keep these sets of cables SEPARATED.
 VACUUM LOADER CONVEYING LINES. Keep them away from all electrical lines,
particularly the Load Cell lines. Conveying plastic produces extreme static sources. A
power supply line, even in conduit, that runs next to a vacuum line, can introduce extreme
static pulses into the processor. Keep conveying lines SEPARATED from electrical supply
lines.
 We use many internal tooth "STAR" washers in assembling the WSB to ensure good
ground between painted parts. Do not remove them.

17
Model Selection
Controllers are programmed to control all sizes of Weigh Scale Blenders. The MODEL number
that your unit is set for will be displayed across the status bar of the controller's Home Screen.
All Weigh Scale Blender controllers come from factory pre-configured for the model blender they
are attached to. If a new blender controller is installed on a blender of a different model, the
controller model may be changed to match the blender. There are 8 main model categories,
each with at least one sub model. The model of the blender can be found on the red serial tag
attached to the blender frame. The possible models are:
Blender Model Batch Weight
(Grams) Weigh Bin Dimensions (DxWxH) Load Cell Rating
mm
Inches
MB / MB1 / MB2
400
127x127x127
5” x 5” x 5”
1 @ 3Kg
140 / 140R / 140MP
1000
254x153x153
6” x 10” x 6”
1 @ 3Kg
220 / 240 / 240R / 260
2000
254x254x178
10” x 10” x 7”
2 @ 3 Kg
420 /
440 / 440R / 460
4000
254x254x254
10” x 10” x 10”
2 @ 10 Kg
940 / 950 / 960
9000
407x407x305
16” x 16” x 12”
2 @ 10 Kg
1840 / 1860
18000
407x407x432
16” x 16” x 17”
2 @ 20 Kg
2400
24000
560x508x458
22” x 20” x 18”
2 @ 20 Kg
3000
30000
407x407x432
20” x 22” x 30”
2 @ 20 Kg
“R” Models have 2 removable hoppers

18
WARNING: Changing Model will set all parameters and settings to factory defaults.
Changing the model will reset the controller's blender configuration settings and
parameters to the defaults for the selected model. System configuration and
preferences will be retained through a model change.
C
hange the model of the blender controller:
Press
Display will show the password keypad screen.
Press
9, 7, 5, 3, 1
then, press
Display will show the Model Selection Screen displaying
the Current Model and the model selection list.
Select
The model series
of your blender.
Models are divided into 8 categories.
Read the red serial tag attached to the blender frame.
Select The series sub-model
of your blender.
The Current Model will display in the upper left.
The New Model will display in the upper right.
Press
To set the new model selection.
The controller will reboot loading factory
default configurations for the new model selection.

19
Touchscreen Controller Parts Key
1. Alarm Strobe Light
2. Main Power Switch
3. Touchscreen
4. Amphenol Connector
5. USB Port
6. Feeder Output
7. Fuse (3 amp)
8. Feeder Output
9. Mix Motor
10. Fuse (3 amp)
11. Level Sensor Connector
12. Audio Beeper
13. Ethernet Communication Port
14. Flex-Lite
15. Serial Communication Port
16. Load Cell Connector
17. Controller Tray (Affixed to WSB)
18. Detachable Remote Touchscreen
Maguire Touchscreen Retrofit Controllers
The Maguire Touchscreen Controller is designed to retrofit onto older Maguire Weigh Scale
Blenders. The Maguire Touchscreen Controller has all of the features of the earlier 6811 (red
display) and 12-12 (blue display) controllers and easily installs on all existing Weigh Scale
Blenders. Retrofitting an earlier Maguire Weigh Scale controller requires setting the model to
match the blender hardware and setting the components to match the hopper configuration.
Touchscreen Remote Mount Option
The Weigh Scale Blender Touchscreen can be remote mounted using Remote Mount Base Kit
equipped with a length of cable, part#: AEK-T4088-xx (xx is the cable length: 01=10ft, 02=20ft,
03=30ft, etc up to 10=100ft). Remote mount instructions:
Remote Mount Base Kit
Part#: AEK-T4088-xx
Remove Allen bolt from
base of controller.
Hang controller on Remote
Mount Base and secure
Allen bolt to controller.
Secure Remote Mount
Base cable to Blender
Controller.

20
Home Screen
Title Bar
Component
Setpoint
Hopper number
Name
Type
Hoppers
9 - 12
START/STOP
Button
Specialized
Operations
Weigh Bin Mix Chamber High / Low Limits Print Center Nav bar
Title Bar - The title bar displays: Model, current Operating Mode (blender, dispenser or Totalizer), date and time, Ethernet
and USB status. Operating Modes are: WAITING, blender is idle (stopped or mix chamber sensor covered).
Navigation Menu – (Nav bar) Located along the right side of the screen, these buttons allow quick navigation to
frequently used and top-level screens. The middle three buttons are soft buttons that can be changed or removed.
Component - This area displays the current configuration of each component (hoppers and feeders), component setpoint,
material name, component type, visible alarms, dispensing indicators (dispensing component hopper number turns yellow
when dispensing). Touch any anywhere on a hopper to access more detail on the individual component. High / Low
Limits, when enabled by the SE or SL component parameters, allow setting a high or low limit on the component.
Hoppers 9 - 12 - The main Home Screen displays hoppers 1 through 8. Hoppers 9 through 12 are displayed on a second
screen accessible by pressing this button. To return to viewing hoppers 1- 8, press this button again. During operation, the
display will automatically toggle to show hoppers that are currently operating.
Weigh Bin – Displays current throughput per hour, current weight in weigh bin, the current dispensing component (hopper
number and type displayed when that component is dispensing), percentage completed of the cycle (green area) and the
portion that is currently dispensing displayed in red. The weigh bin dump flap status (red when closed, green when open).
Mix Chamber – The mix chamber displays the mix chamber level sensor (yellow when cover, gray when uncovered) and
mix motor status (idle or rotating). Below the mix chamber the Flow Control Valve (FCV) status is displayed (red when
closed, green when open).
Start / Stop Button - Main Start and Stop Control Button of the Blender. Also see Automated Control.
Specialized Operations Buttons - When enabled and made visible Specialized Operations Buttons allow access to
specific functions of the blender including View of current totals, Internal Recipe Database, Batch Mode, Tag Information
and FAST mode.