MAK AL-2016A User manual

1

2
USER MANUAL
BEFORE INSTALLING AND USING THIS SYSTEM,
YOU ARE STRONGLY RECOMMENDED TO READ THIS MANUAL CAREFULLY.
MENU
1. Basic Configure- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- (01)
2. Words Explain- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -(02)
3. Attention before using- - - - - - - - - - - - - - - - - - - - - - - - - - - - (03)
4. Feature & Function- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - (04)
5. Main part & instruction- - - - - - - - - - - - - - - - - - - - - - - - - - - - (04)
6. Setting & Operation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -(10)
7. Receive the Alarming phone- - - - - - - - - - - - - - - - - - - - - - - -(19)
8. Remote Control Function- - - - - - - - - - - - - - - - - - - - - - - - - - -(21)
9. System Installation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -(21)
10. Technology Parameter- - - - - - - - - - - - - - - - - - - - - - - - - - - -(22)
11. Normal Fault & Solution- - - - - - - - - - - - - - - - - - - - - - - - - - - -(22)
12. Accessories- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - (23)
1. Basic Configure
AL-2016A

3
2. Word Explain
Arm Set to be Armed(Anti-Burglar), Armed or Make Alarm
Disarm Exit the status of Armed or Stop Alarming
Normal Vocal Arm In Armed status, when being triggered, the siren will be warning and dial the
preset phone number
Mute Arm In Armed status, when being triggered, the siren w ill not be warning but dial
the preset phone number
Stay Arm Setting Armed(Anti-Burglar), User could select the security zone to be
working or not working (After setting, do not affect the normal Arm)
Remote Control Remote Control by the phone to Arm/Disarm or monitor
Phone Line Phone line that could make phone call.
Armed Delay Time from setting Arm to be Armed
Alarm Delay Time from being triggered to Alarm and call.
Warning time of Siren Warning time of Siren
User Password Password for Disarm or remote control
3. Attention before using
(1) Make sure all the Arming zones are on duty.
(2) Avoid heavy impact and unnecessary disassembly which might incur accident or man-made damage.
(3) When installing, avoid touching the electronics components which on the PCB w ith hand or metal
parts.
(4) When installing, make sure the AC power supply is stable (if the AC power supply is cut, the system
will shift to backup battery automatically).
(5) Suggested: main unit should connect w ith phone line. When connect w ith EXT phone, please set the
phone number as requirement. (For Detail, please read below)
(6) When fault, please contact with the dealer or our factory with Invoice & Warrant Card.
4. Feature & Function
(1) LCD DISPLAY
(2) 80 wireless zones, rolling to learn code. 4 wired zones
Wireless transmitting range is more than 200meters.
(3) USA CPU processing circuits, more stable.

4
(4) Billion Code
(5) Available to connect w ith CMS
(6) Available to set each zone to be ON/OFF
(7) Arm/disarm by remote, 2 groups Auto Arm/Disarm, remote to Arm/Disarm, Arm/Disarm by keypad
(8) 72pcs alarm log, show ing event detail & date (year, month, day, hour, minute).
(9) Available to monitor Local, when alarming.
(10) Self-check Function: easy to test & check, for adding new sensor & normal check
(11) Emergency Function.
(12) Built-in 85dB buzzer.
(13) Easy to select w ired/w ireless PIR sensor, Door Sensor, Gas/Smoke Detector and so on.
(14) 12V output port for wired accessories.
5. Main part & instruction
1) Main unit (front)
1. Pow er
indicator
Always on: On duty
Off: Power off
2. Arm/Disarm
Indicator
Always on: in Armed status
Off: in Disarmed status
3. Low-battery
indicator
Always on: Power voltage is lower than
8±0.2V
Off: Power voltage is normal
4.LCD display Display operating menu and event log
5.Keypad For operating
2) Main unit left, right & back side
(1)Antenna: Pull out for better
signal.
(2)Mike: Monitor local, when
answering Arming phone.
(3)Power socket
4) Built-in Buzzer
5) Backup Battery Cover

5
3) Keypad Button
Button Enable Function
“ “key Press“ “key Cancel and go back. Cancel
“ “key Press“ “key Confirm and go to next. Confirm
“↑”key Press“↑”key Move upward, left or backspace. Move &
Backspace
“↓”key Press“↓”key Move downward or right. Move
Number Key：“0”— “9”key。
Set to be armed by
keypad
When mainframe displayed “Welcome”, Press “↑” for 1.5sec., sound “Bi”
once, enter vocal arm status.
4) Main unit (top)
AL-2016A
①Power Button：Power ON/OFF
②Phone port：Connect with phone line or user phone
③Alarming Voltage（12V）output port：Alarming time sy nc with Built-in
Buzzer
④Power（12V）output port：Power for wired accessories.
⑤Wired 4 zone, when connect with one detector, signal wire directly
connect with mainf rame. If more than two, before connect with
mainf rame, please connect the detectors in series.
⑥Wired 3 zone, wiring same as above.
⑦Wired 2 zone, wiring same as above.
⑧Wired 1 zone, wiring same as above.
AL-2016A GSM
Power Button①：Power ON/OFF
SIM card slot②：Insert SIM
G③SM indicator：checking GSM status
GSM Antenna④：For better signal.
⑤EXT-siren (12V) port：Warning time is sync with built-in buzzer.
⑥Power (12V) output port：For wired accessories.
⑦Wired 4 zone (no need resistance)；Connecting with one detector,
directly connect signal wire with this port (4), the other one connect
with public port (⊥). If connect with two or more, please connect them
with in series then connect the port.
Wired 3 zone⑧，same as above.
Wired ⑨2 zone，same as above.
Wired ⑩1 zone，same as above.
A: Press “A” to open SIM card slot with something like toothpick.

6
5) Built-in DIP Sw itch：
AL-2016A
NO. Function Setting
1 ON ON Remotely Control by phone (Def ault is “ON”)
1 OFF
2
ON ON Switch for restoring password (Def ault is “2”), when forgot
password, please open the cov er of mainframe, pull the
switch from “2” to “ON”, then power off, power on after
2sec., pull it to be “2” again. Password restored to be
“000000”
2 OFF
3
ON ON Arm/Disarm dial CMS or not (Def ault is “3”). If pull to “ON”
and input CMS No. & User ID, it will dial CMS, when
Arm/Disarm. Pull to “3”, it will not dial CMS when
Arm/Disarm.
3 OFF
4 Undefined
AL-2016A GSM
NO. Function Setting
1
ON ON Switch f or restoring password(Def ault is “1”), when
f orgot password, please open the cover of mainf rame,
pull the switch f rom “1” to “ON”, then power off, power
on after 2sec., pull it to be “1” again. Password restored
to be “000000”
1 OFF
2
ON ON Sending SMS & dial CMS or not, when Arm/Disarm
(Def ault is “2”). If pull to “ON” and input CMS No., it will
dial CMS. If no input CMS No., it will send SMS to user.
2 OFF
6) Remote Control
OR
Button Enable/Disable Function
ARM KEY
Press key
Sound “Bi”, enter normal ARM
status. To be
Armed
Press key again
Sound “Bi Bi”, enter mute ARM
status.
DISARM
KEY Press key Disarm immediately & exit
alarming status
To be
Disarmed
EMERGENCY
KEY Press key Warn & Dial at once To be
Emergency
PERIMETER
ARM KEY
Press key
Sound “Bi”, enter perimeter
Armed To be
Perimeter
Armed
Press & key at
the same time
Enter v ocal armed status without
any delay.

7
6. System Setting and Operation
Pow er on, LCD w ill be on, then operating as below:
Ⅰ. NORMAL
(1). PHONE
(2). CMS
(3). PASSWORD
(4). TIME&DATE
Ⅱ. ADVANCED

8
(1). LEARN CODE
(2). REMOVE

9
(3). SETTING
(4). SELF CHECK
(5). ALARM LOG
(6). AUTO ARM/DISARM

10
(7)Default setting
1.Delay to be Armed： 0sec. 5.Built-in Buzzer & EXT Siren：
SYNC.
2.Delay to be Disarmed： 0sec. 6.The 1st zone： Normal Zone
3.When Armed, default is：
Global Armed 7.Alarm Phone default is： Null
4.default password： 000000
7. Receive the Alarming call
In armed status, if any accessories are being triggered, the system will make alarm after delay time.
(1) Warning Alarm
If no connecting with phone line or do not input any number, when being triggered, the siren w ill be
warning in any status.
Except the above two vocal alarming situation, If under mute alarm status, the siren w ill not warn.
(2) Phone Alarm
When alarming, the system w ill dial in order. If not being stopped, it will dial three times in cycle. (As
below)
If connecting with CMS, it w ill dial CMS first and send alarming information. If sent successfully, it w ill
not dial CMS again. If not, it will dial CMS three times. Then dial other three groups in cycle. (As below)
When answer the phone, firstly it is the operating voice prompt. It is available to operate according to the
voice prompt. If the user does some operating, it w ill not dial this number in another cycle.