Mobeye i110 User manual

User manual
Mobeye®i110
SW version 7N

Table of content
1. Introduction 1
2. To get ready in four steps 2
2.1 Step 1: SIM Card 2
2.2 Step 2: insert the batteries 2
2.3 Step 3: Program the phone numbers 3
2.4 Step 4: Check the settings 3
3. Switching the motion detector on/off 4
3.1 Switching on 4
3.2 Switching off 4
4. Mobeye settings 5
4.1 Configuration 5
4.2 Installation code 6
4.3 SMS custom text 6
4.4 Telephone numbers 7
4.5 SMS on/off 7
4.6 Call on/off 7
4.7 Sensor sensitivity 7
4.8 Entry delay 7
4.9 Entry indication 8
4.10 Siren 8
4.11 Exit indication 8
4.12 Temperature alarm 8
4.13 Adjusting the temperature 8
4.14 Interval test message 9
4.15 Setting the current time and date 9
4.16 User code 9
5. Advanced options 10
5.1 Request settings 10
5.2 Reset to factory settings 10
5.3 Leave the menu 10
5.4 Position of Mobeye 11
5.5 Test GSM network strength 12
6. Issue solving 13
7. Technical data 14

Attention! Very important
This user manual contains important guidelines for the installation and
usage of the Mobeye®i110. Please read these thoroughly before you start
using the Mobeye®!
In case of damage caused by disregarding the guidelines, the warranty
becomes void.
The user must regularly check the proper functioning of the Mobeye®. The
manufacturer cannot be held liable for any damage or loss caused by any
incorrect use or incorrect functioning of the Mobeye® i110.
Safety guidelines
 The permitted ambient temperature during operation may not be
exceeded (not lower than -10°C and not higher than 55°C).
 The device is intended for use in dry and clean places.
 Protect the device from moisture, heat and water splashing. Not intended
for external use.
 The guidelines for the battery usage must be regarded.
 Do not expose the device to strong vibrations.
 Do not let it fall from height.
 Do not use in an environment where any inflammable gases, vapours or
dust are present or could be present.
 Repair of the device may only be carried out by people, trained for
Mobeye®repair.
 If the device must be repaired, only original replacement components
may be used. The use of different parts may lead to damage of the
Mobeye®.
Use in accordance with the regulations
The purpose of this device in accordance with the regulations is the
generation of SMS text messages and telephone calls after detection of
motion by the motion detector or after a temperature was measured that
outreaches the programmed limits.
Other uses are not permitted and may invalidate the warrantee.

1
1. INTRODUCTION
The Mobeye i110 is an easy to install alarm
system that will notify you about a detection
using the built-in GSM communication
module.
To use the Mobeye i110 you will need a SIM-
card of any provider.
Typical applications are the security of places
without any power supply or the temporary security of properties.
The Mobeye i110 has the following features.
Alarm notifications after movement detection
In case of the detection of an intruder, the Mobeye i110 will send an SMS
text message to your phone(s). The Mobeye i110 will also call the phone
numbers in order to be sure the message is not missed. It is possible to set
the siren sound. Following the standby period of 5 minutes, the Mobeye will
resume alerting you to new movement.
Alarm notifications after detection of out of range temperature
It is possible to program a minimum and/or maximum temperature alert in to
the Mobeye i110. It will monitor the actual temperature of its environment
and send an alert as soon as the temperature reaches the limit.
Low battery message
The Mobeye i110 will send an SMS text message when the batteries need
to be replaced. When you receive this message, you need to change the
batteries as soon as possible, although the Mobeye i110 will continue to
function for a short time following the message. Even when the Mobeye
i110 is unset, it will measure the battery strength and send the message.
Private numbers or Mobeye Internet Portal
The Mobeye i110 sends alarm messages to one or two telephone numbers.
As an option the Mobeye i110 can be connected to the Mobeye Internet
Portal for extended functionality. Please refer to www.mobeye.eu for more
information.

2
2. TO GET READY IN FOUR STEPS
To get started with the Mobeye i110 only four steps are needed.
1. Place the SIM card in the Mobeye i110.
Make sure this SIM card is not secured by a PIN code.
2. Insert the four batteries.
3. Enter at least one phone number in the Mobeye i110.
4. Check the settings.
In this chapter these steps are explained.
2.1 STEP 1: SIM CARD
To use the Mobeye i110 a SIM card from any network is needed. On this
SIM card, the PIN code security needs to be disabled. If you have a SIM
card with PIN code, you can disable this using any mobile phone and switch
off the PIN code security. Please consult the manual for that mobile phone
for the procedure.
The SIM card needs to be inserted before the batteries. When using a
prepaid SIM card, take note of the available credit. Additionally it is wise to
set a recurrent test message in the menu so the card will be used at least
once a month.
Open the back cover (insert a key or screwdriver
into one of the deeper holes and pull back slowly).
Insert the SIM card in the holder. For
opening/closing, move the cover slightly.
2.2 STEP 2: INSERT THE BATTERIES
Insert the four lithium 3,0 volt batteries (CR123). When replacing the
batteries, all settings remain unchanged.
After inserting the SIM card and the batteries, the Mobeye i110 will perform
a self test taking 1 minute. During the test, the light is red. If the light is
flashing red, a problem with the SIM card is detected. A reason could be no
SIM card was placed, or the PIN code security of the SIM card was not
disabled.
Close the Mobeye i110 using the 4 screws.

3
2.3 STEP 3: PROGRAM THE PHONE NUMBERS
You need to program at least one phone number in the unit as alarm
receiving number.




Enter the phone number (e.g. 0712345678)

The light turns green and a confirmation melody is played.
The Mobeye i110 is ready to use.
2.4 STEP 4: CHECK THE SETTINGS
The settings can be sent to the programmed telephone number as SMS
text message. In this way you also check the correct working of the SIM
card.




Within ca. 30 seconds the set phone number will receive the list with
settings.

4
3. SWITCHING THE MOTION DETECTOR ON/OFF
3.1 SWITCHING ON
To activate the Mobeye i110 movement detector with your personal
installation code.


The light turns red shortly and an indication tone is started. This repetitive
tone will last during the exit delay of 60 seconds. As soon as the acoustic
signal stops, the Mobeye i110 is active.
If the installation code is entered incorrectly 3 times, the indicator turns red
and the Mobeye i110 will be blocked for 10 minutes.
3.2 SWITCHING OFF
To de-activate the Mobeye i110 movement detector with your personal
installation code.


The light switches to green and a confirmation melody is played.

5
4. MOBEYE SETTINGS
The Mobeye i110 settings can be changed via the keypad and SMS text
messages. First the method of programming is discussed, next the
explanation of the settings.
4.1 CONFIGURATION
To change the settings, please follow these instructions:

- light turns green
Enter the menu number (see list below)

Enter the new setting

is played
In the event of incorrect entries, the light turns red and a short beep will sound.

Following settings are possible:
Menu
nr
Description
Options
Factory
setting
00
Change installation code
4 digit code
1111
01
Change 1st tel.nr.
Tel. number (0 to delete)
-
02
Change 2nd tel.nr.
Tel. number (0 to delete)
-
03
Sensor sensitivity
1,2
1 (high)
04
Entry delay
15, 30, 45 or 60
15 (sec.)
05
Interval test message
0-30 (days)
0 (no message)
07
Entry indication
0 (off), 1 (on), 2 (LED)
0
08
Siren
0 (off), 1 (on)
0
09
Exit indication
0 (off), 1 (on)
1
12
SMS on/off
0 (off), 1 (on)
1
13
Call on/off
0 (off), 1 (on)
1
41
Change minimum
temperature
000-050 (0 until 50ºC)
110-101 (-10 until -1 ºC)
999 = off
999
42
Change maximum
temperature
000-050 (0 until 50ºC)
110-101 (-10 until -1 ºC)
999 = off
999
49
Correction factor
temperature
01-09 (+1 to +9 ºC)
11-19 (-1 to -9 ºC)
00 (no correction)
00
50
Change user code
4 digit code
8888
60
Actual time
hhmm (e.g.1530)
-
61
Actual date
yyyymmdd (e.g. 20140331)
-

6
4.2 INSTALLATION CODE
The installation code is the code for switching on/off the active status. In the
active status the Mobeye i110 will detect movements. The installation code
is also needed to program the settings or activate the special functions. It is
possible to change the installation code to any 4-digit number. Please
change the code to make the unit more secure. If the installation code is
entered incorrectly 3 times, the indicator turns red and the Mobeye i110will
be blocked for 10 minutes.
4.3 SMS CUSTOM TEXT
A custom text can be added in the SMS text messages, to identify which
Mobeye i110unit sent the message. The second part of the SMS text

custom text is written before the standard text.
This custom text (max. 20 characters) can be programmed by sending an
SMS to the Mobeye i110. Changing the custom text cannot be done via the
keypad, only via sending an SMS text message.
Switch the Mobeye i110 into the programming mode. In this mode the GSM
module is switched on and is able to receive messages.
Enter your 4-

-> light turns green

First the light flashes red (interval ca. 1 sec). As soon as the light turns
green, the Mobeye i110is able to receive SMS-messages.
To program the custom text, send an SMS in following structure:
To program the custom text, send an SMS in following structure:
1111 NAME:myowntext
-
-
--defined text (max. 20 characters)
-Be aware of the space after 1111 and the colon after NAME
You will hear two short beeps in case of a correct command.


7
4.4 TELEPHONE NUMBERS

one or two telephone number. At least one telephone number must be
entered in the Mobeye i110. The test messages and low battery messages
are sent to the first programmed telephone number.
4.5 SMS ON/OFF
By default, the Mobeye i110 sends alarm notifications via text message and
calls to the preset contact persons. By turning off the SMS, the unit will only
call after the movement sensor detects an alarm. Regardless of this setting
the temperature alarm always sends an SMS including the actual
temperature.
4.6 CALL ON/OFF
By default, the Mobeye i110 sends alarm notifications via text message and
calls to the preset contact persons. By turning off the CALL, the unit will
only send an SMS text message as alarm notification. It is not possible to
switch off both.
4.7 SENSOR SENSITIVITY

1= High
2 = Low
In the high sensitivity mode each detection will generate an alarm. In the
lower sensitivity mode the alarm will be generated only when the detector is
activated twice in any 15 seconds period. This mode prevents false alarms
in case of e.g. draught and is most suitable if the sensor is directed towards
an open space.
4.8 ENTRY DELAY
It is possible to choose from 4 entry delay times. The entry delay is the time
between the moment of detection and the moment of sending the first SMS
text message.
Important note: If the GSM network has low signal strength, the time can be
longer as the network connection may not be established within the time of
the entry delay.

8
4.9 ENTRY INDICATION
No entry indication is set a the factory default. It is possible to hear an
indication beep during the entry delay. This can be used as a reminder that
the Mobeye is in active mode. It is also possible to let the LED indicator
flash a few times, as an indicator for the user.
4.10 SIREN
After the entry delay, the siren can sound for two minutes. At the same time
the SMS text messages and telephone calls will be sent. At soon as the
Mobeye is switched off, the siren will stop. The siren is set to silent as the
factory default.
4.11 EXIT INDICATION
Upon arming the system, you have one minute to leave the room. The PIR
is not active yet and an exit indication sounds. It is possible to change this
to a silent exit time. A short beep is heard and the LED flashes red during
the exit time.
4.12 TEMPERATURE ALARM
The Mobeye i110 is able to send a temperature alarm as soon as the actual
temperature reaches a programmed min. or max. level. This function can
be used independently of the motion detection. As soon as the temperature
is too high or too low, an SMS text message is sent, followed by a
telephone call. As long as the out of range temperature remains, the report
will be repeated hourly. Once the temperature is back to normal, the
Mobeye i110 confirms this to you.
This function is active as soon as a temperature limit is programmed. By
resetting the limits, the function becomes inactive.
4.13 ADJUSTING THE TEMPERATURE
The built-in temperature sensor may have a standard deviation of the actual
temperature. In this case, the deviation will be similar at all temperatures. It
is possible to correct the temperature deviation in the Mobeye i110. In the
SMS setting summary, you see the reported temperature. If a correction is
specified, it is processed in the displayed temperature; the correction factor
itself is displayed separately.
Example: Mobeye temperature: 13 C. Actual temperature: 14 C. To
correct this deviation, one degree should be added.

9
4.14 INTERVAL TEST MESSAGE
The Mobeye i110 can send test messages. Through these test reports you
will be informed of the status of your system. The interval between test
reports is adjustable between 0 (no test reported) and 30 (once every 30
days). Note: the interval of 1 day will result in a daily test message; the
exact time between the messages will be about 24 hours.
The smaller the interval between the test reports, the shorter is the battery
life. The test message only works if the system is on or a temperature limit
is set.
4.15 SETTING THE CURRENT TIME AND DATE
Some telecom providers offer this in the network, which is updated by the
Mobeye i110 during the start-up and after sending test messages. It is
possible to set the time and date manually. To view the clock time, send a
list of the settings to the first phone number (CODE MENU 10 OK).
4.16 USER CODE
The Mobeye i110 offers the possibility to set a personal 4-digit user code,
for just arming and disarming the system. It is not possible to change the
settings with the user code. The system needs to be switched on and off
using the same code; the installation code and user code are not
interchangeable. Factory sett
be changed by the installation code or user code (menu number 50). We
recommend you to change this code to make the unit more secure.

10
5. ADVANCED OPTIONS
5.1 REQUEST SETTINGS
The settings can be sent to the set telephone number as SMS text
message. In this way you also check the correct working of the SIM card.




Within ca. 30 seconds the first phone number will receive the list with
settings.
5.2 RESET TO FACTORY SETTINGS
It is possible to reset the Mobeye i110 to factory settings.




After several seconds a short confirmation tone is heard. The installation
code is also reset to 1111.
5.3 LEAVE THE MENU


11
5.4 POSITION OF MOBEYE
The built-in motion sensor has a 360º detection pattern and has a range of
about 8 meters. The Mobeye i110can be positioned both vertically as
horizontally. It can be mounted to the wall, put down on its side in a cabinet,
put down with its sensor upward or downward. If you want to hang the
Mobeye i110, the pre-punched holes can be opened, in order to hang it on
screws.
In order to check the positioning of the sensor, a sensor test can be
executed.




A confirmation beep is heard. First the green light will be flashing. After
about 30 seconds the light will be on continuously.
In this mode the sensor test can be done; each time the sensor detects a
movement, a repeating beep will sound.
Leave the test by entering OK twice.

12
5.5 TEST GSM NETWORK STRENGTH
Before using the Mobeye i110 is it advised to test the GSM signal strength
at the location.




The Mobeye i110 now switches on the GSM module and searches for all
available networks. It also checks the network strength of the SIM card
provider in the device.
As soon as the GSM network is found, the light will turn green.
The GSM signal strength for the network your SIM is using can be gauged
from the LED indicator:
LED
Description
Green during 30 seconds
Signal is very good
Flashing green
Signal is good
Red
Signal is weak
Flashing red
No valid SIM card or SIM card is not
pin code free or no signal
The telephone number at memory position 01 will receive an SMS text
message, containing all existing GSM networks, sorted by provider. It also
tells the strength of each network.
This search function can take a few minutes. If you want to leave the

Warning
In the event of a weak signal, the Mobeye i110can still be used, but there is
a risk that messages cannot be sent or will be received with a delay. In
case of no signal, it is advised to try a different network.

13
6. ISSUE SOLVING
Error
Possible reason
Solution
Mobeye i110 cannot be
switched on. You hear an
error tone, the red light is
turned on shortly.
No valid Telephone
number was entered.
Enter a valid number.
The light is flashing during
switching on.
No valid SIM card was
entered or the SIM
card was not made pin
code free.
Check the SIM card.
It is impossible to change
the settings. After entering
the installation code,
followed by menu, the
error tone is played and
the light turns red.
Mobeye is activated.
Switch off the Mobeye
i110.
No GSM signal during the
GSM test
No network is
available, belonging to
the SIM cards provider.
Choose another
network provider.
The light remains red.
You entered an
incorrect installation
code three times.
Wait 10 minutes and
then re-enter the
correct installation
code.
You do not receive an
SMS with the settings.
Telephone number is
not correct.
Re-program the
telephone number
Change the menunr.06

For other questions, please refer to the site www.mobeye.eu

14
7. TECHNICAL DATA
 GSM: Quad Band EGSM 850/900/1800/1900 MHz
compatible to the ETSI GSM Phase 2+ standard
 Output power:
Class 4 (2W @ 900 MHz)
Class 1 (1W @ 1800 and 1900 MHz)
 Temperature range: -10°C until +55°C
 Weight: ca. 275 gram incl. batteries
 Dimensions: 161 x 90 x 35 mm (LxWxH)
 Batteries:4 x CR123 Lithium 3.0 V
 
Support
For support on technical problems regarding Mobeye i110 please contact
[email protected].
CONRAD IM INTERNET http://www.conrad.de
This manual is published by Mobeye.
All rights, the translation included are reserved. Any reproduction,
either photocopy, microfilm or saved in an automated data dictionary,
only after written approval of the Publisher. Reprinting, even in
summary, is prohibited.
This user manual meets the technical requirements at the moment of
printing. Changes in technology and equipment are reserved.
© Copyright by Mobeye, version I110EN161106

Declaration of Conformity
Herewith we, Mobeye, declare that the product
Mobeye i-110
is in compliance with the essential requirements of the following European
standards / EU Directives:
Directive 73/23/EEC (low voltage directive)
Directive IEC/EN 50130 Electromagnetic compatibility
Directive 1995/5/EC R&TTE (Radio & Telecommunications
Terminal Equipment)
The conformity with the essential requirements of 1995/5/EC
has been verified against:
ETSI EN 301 489-1 V1.5.1
ETSI EN 301 489-7 V1.2.1
ETSI EN 301 511 V9.0.2
CENELEC EN 60950:2001
Mobeye B.V.
Poeldonkweg 5
-Hertogenbosch
The Netherlands
Name: J.P.K. van de Vijver
Position: Managing Director
Signature:
Date: 1 Augustus 2012