Makita UM603D User manual

UM603D
EN Cordless Grass Shear INSTRUCTION MANUAL 9
SL Brezžične škarje za travo NAVODILA ZA UPORABO 17
SQ Gërshërë bari me bateri MANUALI I PËRDORIMIT 25
BG Акумулаторна ножица за
трева
РЪКОВОДСТВО ЗА
ЕКСПЛОАТАЦИЯ 34
HR Bežične škare za travu PRIRUČNIK S UPUTAMA 44
МК Безжична ножица за трева УПАТСТВО ЗА УПОТРЕБА 52
SR Бежичне маказе за траву УПУТСТВО ЗА УПОТРЕБУ 62
RO Foarfecă de iarbă fără cablu MANUAL DE INSTRUCŢIUNI 71
UK Акумуляторні ножиці для
підрізання трави
ІНСТРУКЦІЯ З
ЕКСПЛУАТАЦІЇ 80
RU Аккумуляторные ножницы
для травы
РУКОВОДСТВО ПО
ЭКСПЛУАТАЦИИ 90

12
3
Fig.1
1
2
Fig.2
1
Fig.3
1
Fig.4
Fig.5
Fig.6
1
Fig.7
2

2
1
Fig.8
Fig.9
Fig.10
Fig.11
3
2
1
Fig.12
1 2 3
Fig.13
Fig.14
1
Fig.15
3

1
Fig.16
Fig.17
Fig.18
Fig.19
Fig.20
1
Fig.21
Fig.22
Fig.23
4

Fig.24
1
Fig.25
1
Fig.26
1 2
3
Fig.27
Fig.28
1
Fig.29
1
Fig.30
Fig.31
5

1
Fig.32
1
Fig.33
Fig.34
Fig.35
1
Fig.36
1
2
Fig.37
1
Fig.38
Fig.39
6

Fig.40
Fig.41
Fig.42
Fig.43
Fig.44
Fig.45
Fig.46
Fig.47
7

Fig.48
Fig.49
Fig.50
Fig.51
Fig.52
1
Fig.53
1
Fig.54
8

9ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: UM603D
Cutting width 160 mm
Strokes per minute 2,500 min-1
Dimensions
(L x W x H)
343 mm x 177 mm x 131 mm
Rated voltage D.C. 18 V
Battery cartridge BL1815G
Net weight 1.5 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsandbatterycartridgemaydifferfromcountrytocountry.
• Weight,withbatterycartridge,accordingtoEPTA-Procedure01/2003
Symbols
Thefollowingshowthesymbolsusedfortheequip-
ment.Besurethatyouunderstandtheirmeaningbefore
use.
Takeparticularcareandattention.
Read instruction manual.
Danger;beawareofthrownobjects.
Keepbystandersaway.
Cuttingmeanscontinuestorunafterthe
motorisswitchedoff.
Do not expose to moisture.
Cd
Ni-MH
Li-ion
OnlyforEUcountries
Donotdisposeofelectricequipmentor
batterypacktogetherwithhouseholdwaste
material!
InobservanceoftheEuropeanDirectives,
onWasteElectricandElectronic
EquipmentandBatteriesandAccumulators
andWasteBatteriesandAccumulators
and their implementation in accordance
withnationallaws,electricequipmentand
batteriesandbatterypack(s)thathave
reachedtheendoftheirlifemustbecol-
lected separately and returned to an envi-
ronmentallycompatiblerecyclingfacility.
Intended use
Thetoolisintendedforcuttinglawnedgesorsprouts.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ingtoEN50636:
UM603D with shear blade for grass shear installed
Sound pressure level (LpA):76dB(A)
Uncertainty(K):1.82dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
WARNING: Wear ear protection.
ThetypicalA-weightednoiseleveldeterminedaccord-
ingtoEN60745:
UM603D with shear blade for hedge trimmer
installed
Sound pressure level (LpA):74dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
WARNING: Wear ear protection.
Vibration
Thevibrationtotalvalue(tri-axialvectorsum)deter-
minedaccordingtoEN50636:
UM603D with shear blade for grass shear installed
Vibrationemission(ah):2.5m/s2or less
Uncertainty(K):1.5m/s2
Thevibrationtotalvalue(tri-axialvectorsum)deter-
minedaccordingtoEN60745:
UM603D with shear blade for hedge trimmer
installed
Vibrationemission(ah):2.5m/s2or less
Uncertainty(K):1.5m/s2
NOTE:Thedeclaredvibrationemissionvaluehas
beenmeasuredinaccordancewiththestandardtest
methodandmaybeusedforcomparingonetoolwith
another.
NOTE:Thedeclaredvibrationemissionvalue
mayalsobeusedinapreliminaryassessmentof
exposure.

10 ENGLISH
WARNING: Thevibrationemissionduringactual
useofthepowertoolcandifferfromthedeclaredemission
value depending on the ways in which the tool is used.
WARNING: Besuretoidentifysafetymeasurestopro-
tecttheoperatorthatarebasedonanestimationofexposure
intheactualconditionsofuse(takingaccountofallpartsofthe
operatingcyclesuchasthetimeswhenthetoolisswitchedoff
and when it is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
TheECdeclarationofconformityisincludedasAnnexA
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool.Failuretofollowallinstructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm"powertool"inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.
Cordless Grass Shear Safety
Warnings
General instructions
1. To ensure correct operation, user has to read
this instruction manual to make himself famil-
iar with the handling of the equipment.Users
insufcientlyinformedwillriskdangertothem-
selves as well as others due to improper handling.
2.
Never allow children, persons with reduced phys-
ical, sensory or mental capabilities or lack of
experience and knowledge or people unfamiliar
with these instructions to use the machine, local
regulations may restrict the age of the operator.
3. Use the equipment with the utmost care and attention.
4. Operate the equipment only if you are in good
physical condition. Perform all work calmly and
carefully. Use common sense and keep in mind that
the operator or user is responsible for accidents or
hazards occurring to other people or their property.
5. Never operate the machine while people, espe-
cially children, or pets are nearby.
6.
The motor is to be switched off immediately in case that
the equipment shows any problem or abnormal sign.
7. Switch off and remove the battery cartridge when
resting and when leaving the equipment unat-
tended, and place it in a safe location to prevent
danger to others or damage to the equipment.
8. Avoid using the machine in bad weather condi-
tions especially when there is a risk of lightning.
Personal protective equipment
1. Wear eye protection and stout shoes at all
times while operating the machine.
2. Always wear substantial footwear and long
trousers while operating the machine.
Starting up the equipment
1. Make sure that there are no children or other
people nearby, also pay attention to any ani-
mals in the working vicinity. Otherwise stop
usingtheequipment.
2. Before use always check that the equipment
is safe for operation. Check the security of the
cutting tool and the guard and the switch trig-
ger/lever for easy and proper action. Check for
clean and dry handles and test the function of
the start/stop.
3.
Check damaged parts before further use of the
equipment. A guard or other part that is dam-
aged should be carefully checked to determine
that it will operate properly and perform its
intended function. Check for alignment of mov-
ing parts, binding of moving parts, breakage of
parts, mounting, and any other condition that
may affect its operation. A guard or other part
that is damaged should be properly repaired
or replaced by our authorized service center
unless indicated elsewhere in this manual.
4. Switch on the motor only when the hands and
feet are away from the cutting tool.
5. Before starting make sure that the cutting tool
has no contact with any objects.
Method of operation
1. Only use the equipment in good light and
visibility. During the winter season beware
of slippery or wet areas, ice and snow (risk
of slipping). Always ensure a safe footing on
slopes and be sure to walk and never run.
2. Take care against injury to feet and hands from
the cutting tool.
3. Never stand on a ladder and run the
equipment.
4. Never climb up into trees to perform cutting
operation with the equipment.
5. Never work on unstable surfaces.
6.
Remove sand, stones, nails etc. found within the
working range. Foreign particles may damage the
cuttingtoolandcancausedangerouskick-backs.
7. Should the cutting tool hit stones or other hard
objects, immediately switch off the motor and
inspect the cutting tool.
8. Inspect the cutting tool at short regular inter-
vals for damage (detection of hairline cracks
by means of tapping-noise test).
9. Before commencing cutting, the cutting tool
must have reached full working speed.
10.
The cutting tool has to be equipped with the
appropriate guard. Never run the equipment with
damaged guards or without guards in place!
11. All protective installations and guards sup-
plied with the equipment must be used during
operation.

11 ENGLISH
12. Always remove the battery cartridge from the
equipment:
— whenever leaving the equipment
unattended;
— before clearing a blockage;
— before checking, cleaning or working on
the equipment;
— after striking a foreign object;
— whenever the equipment starts vibrating
abnormally.
13. Always ensure that the ventilation openings
are kept clear of debris.
14. Cutting means continues to run after the motor
is switched off.
Cutting Tools
Employ only the correct cutting tool for the job
in hand.
Maintenance instructions
1. The condition of the equipment, in particular of
the cutting tool of the protective devices must
be checked before commencing work.
2. Turn off the motor and remove the battery
cartridge before carrying out maintenance,
replacing cutting tools or cleaning the equip-
ment or cutting tool.
3. When not in use, store the equipment indoors
in dry and high or locked-up place - out of the
reach of children. Clean and maintain before
storage.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Cordless Hedge Trimmer Safety
Warnings
1. Keep all parts of the body away from the cut-
ter blade. Do not remove cut material or hold
material to be cut when blades are moving.
Make sure the switch is off when clearing
jammed material.Amomentofinattentionwhile
operating the hedge trimmer may result in serious
personalinjury.
2. Carry the hedge trimmer by the handle with
the cutter blade stopped. When transporting or
storing the hedge trimmer always t the cut-
ting device cover.Properhandlingofthehedge
trimmerwillreducepossiblepersonalinjuryfrom
thecutterblades.
3. Hold the power tool by insulated gripping
surfaces only, because the cutter blade may
contact hidden wiring.Cutterbladescontacting
a"live"wiremaymakeexposedmetalpartsofthe
powertool"live"andcouldgivetheoperatoran
electric shock.
4. Do not use the hedge trimmer in the rain or in
wet or very damp conditions.Theelectricmotor
isnotwaterproof.
5. First-time users should have an experienced
hedge trimmer user show them how to use the
trimmer.
6. The hedge trimmer must not be used by
children or young persons under 18 years of
age.Youngpersonsover16yearsofagemaybe
exemptedfromthisrestrictioniftheyareundergo-
ingtrainingunderthesupervisionofanexpert.
7. Use the hedge trimmer only if you are in good
physical condition.Ifyouaretired,yourattention
willbereduced.Beespeciallycarefulattheendof
aworkingday.Performallworkcalmlyandcare-
fully.Theuserisresponsibleforalldamagesto
third parties.
8. Never use the trimmer when under the inu-
ence of alcohol, drugs or medication.
9. Work gloves of stout leather are part of the
basic equipment of the hedge trimmer and
must always be worn when working with it.
Also wear sturdy shoes with anti-skid soles.
10. Before starting work check to make sure
that the trimmer is in good and safe working
order. Ensure guards are tted properly. The
hedge trimmer must not be used unless fully
assembled.
11. Make sure you have a secure footing before
starting operation.
12. Hold the tool rmly when using the tool.
13. Do not operate the tool at no-load
unnecessarily.
14. Immediately switch off the motor and remove
the battery cartridge if the cutter should come
into contact with a fence or other hard object.
Check the cutter for damage, and if damaged
repair immediately.
15. Before checking the cutter, taking care of
faults, or removing material caught in the cut-
ter, always switch off the trimmer and remove
the battery cartridge.
16. Switch off the trimmer and remove the battery
cartridge before doing any maintenance work.
17. When moving the hedge trimmer to another
location, including during work, always
remove the battery cartridge and put the blade
cover on the cutter blades. Never carry or
transport the trimmer with the cutter running.
Never grasp the cutter with your hands.
18.
Clean the hedge trimmer and especially the
cutter after use, and before putting the trimmer
into storage for extended periods. Lightly oil the
cutter and put on the cover.Thecoversupplied
withtheunitcanbehungonthewall,providinga
safeandpracticalwaytostorethehedgetrimmer.
19. Store the hedge trimmer with the cover on, in
a dry room. Keep it out of reach of children.
Never store the trimmer outdoors.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.

12 ENGLISH
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3.
If operating time has become excessively shorter,
stop operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current ow,
overheating, possible burns and even a breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10.
The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
Forcommercialtransportse.g.bythirdparties,
forwardingagents,specialrequirementonpack-
agingandlabelingmustbeobserved.
Forpreparationoftheitembeingshipped,consultingan
expertforhazardousmaterialisrequired.Pleasealso
observepossiblymoredetailednationalregulations.
Tapeormaskoffopencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwillalso
voidtheMakitawarrantyfortheMakitatoolandcharger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely dis-
charged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
battery cartridge cool down before charging it.
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Using the tool as cordless hedge
trimmer
Thistoolcanbeusedasacordlesshedgetrimmerby
installingtheshearbladesforhedgetrimmer(optional
accessory).
Installing or removing battery
cartridge
CAUTION: Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipoffyourhands
andresultindamagetothetoolandbatterycartridge
andapersonalinjury.
►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
it into place. Insert it all the way until it locks in place
withalittleclick.Ifyoucanseetheredindicatoronthe
uppersideofthebutton,itisnotlockedcompletely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen.Ifnot,
itmayaccidentallyfalloutofthetool,causinginjuryto
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.
Tool / battery protection system
Thetoolisequippedwithatool/batteryprotectionsys-
tem.Thissystemautomaticallycutsoffpowertothe
motortoextendtoolandbatterylife.Thetoolwillauto-
maticallystopduringoperationifthetoolorbatteryis
placedunderoneofthefollowingconditions:
Overload protection
Whenthebatteryisoperatedinamannerthatcauses
ittodrawanabnormallyhighcurrent,thetoolautomati-
callystops.Inthissituation,turnthetooloffandstopthe
applicationthatcausedthetooltobecomeoverloaded.
Thenturnthetoolontorestart.

13 ENGLISH
Overheat protection
Whenthetoolorbatteryisoverheated,thetoolstops
automaticallyandthelampblinks.Inthiscase,letthe
toolandbatterycoolbeforeturningthetoolonagain.
Overdischarge protection
Whenthebatterycapacityisnotenough,thetoolstops
automatically.Ifyouturnthetoolon,themotorruns
againbutstopssoon.Inthiscase,removethebattery
fromthetoolandchargethebattery.
Switch action
WARNING: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
WARNING: For your safety, this tool is
equipped with the lock-off button which prevents
the tool from unintended starting. Never use the
tool if it starts when you pull the switch trigger
without pressing the lock-off button.Askyourlocal
MakitaServiceCenterforrepairs.
WARNING: Never disable the lock function or
tape down the lock-off button.
NOTICE: Do not pull the switch trigger forcibly
without pressing the lock-off button.Theswitch
maybreak.
►Fig.2: 1. Switch trigger 2.Lock-offbutton
Tostartthetool,depressthelock-offbuttonandpullthe
switchtrigger.Releasetheswitchtriggertostop.The
lock-offbuttoncanbepressedfromeithertherightor
leftside.
Indicator lamp
Theindicatorlampblinksorlightsupwhentheremain-
ingbatterycapacityisloworempty.Theindicatorlamp
alsolightsupwhenthetoolbecomesoverloaded.
►Fig.3: 1. Indicator lamp
Lamp status and action to be taken
Indicator lamp Status Actiontobetaken
Thelampblinks
red.
Theremaining
batterycapacity
is low.
Chargethebattery.
Thelamplightsup
red. *
Thetoolhas
stoppedbecause
the remaining
batterycapacityis
empty.
Chargethebattery.
Thetoolhas
stopped due to
overload.
Turnoffthetool.
*Thetimeatwhichtheindicatorlamplightsupvariesdepending
onthetemperaturearoundtheworkareaandthebatterycar-
tridge conditions.
Adjusting the shearing height (for
grass shear)
CAUTION: When changing the shearing
height, be sure to attach the blade cover and be
careful not to trap ngers between the tool and
grass receiver.
Theshearingheightcanbesettothreelevels(15mm,
20mm,and25mm)bychangingthexedpositionof
thegrassreceiver.Theshearingheightwithoutthe
grassreceiverisabout10mm.
1. Slidethegrassreceivertowardthefrontofthe
tool.
►Fig.4: 1. Grass receiver
2. Changethexedpositionofthegrassreceiverby
movingitinthedirectionofthearrow.
►Fig.5
NOTE:Theshearingheightvalueisaguideline.The
actual shearing height may vary depending on the
conditionofthelawnortheground.
NOTE:Tryatestshearinginalessconspicuous
place to get your desired height.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION: When replacing the shear blades,
always wear gloves and attach the blade cover so
that your hands and face do not directly contact
the blades.
NOTICE: When replacing the shear blades, do
not wipe off grease from the gear and crank.
Installing or removing the blade
cover
CAUTION: Be careful not to touch the blades
when installing or removing the blade cover.
Toremovethebladecover,pullitslightly,andthenslide
itsideways.Toinstallthebladecover,performthesteps
in reverse.
►Fig.6
Installing or removing the grass
receiver
CAUTION: When installing or removing the
grass receiver, be sure to attach the blade cover
and be careful not to trap your ngers between
the tool and grass receiver.

14 ENGLISH
Removing the grass receiver
1. Release the protrusions on the grass receiver
fromthegroovesonthetoolwhileslidingthegrass
receivertowardthefrontofthetool.
►Fig.7: 1. Grass receiver
2.
Releasethehingeofthegrassreceiverfromthetool.
Installing the grass receiver
1. Hookthehingeofthegrassreceiveronthegroove
ofthetool.
►Fig.8: 1. Hinge 2. Grass receiver
2.
Aligntheprotrusionsonthegrassreceiverwiththe
groovesonthetoolbyslidingthegrassreceivertowardthe
frontofthetoolandmovingitinthedirectionofthearrow.
►Fig.9
NOTICE: Do not attach the hinge of the grass
receiver to the tool forcibly after aligning the pro-
trusions on the grass receiver with the grooves
on the tool.
Installing or removing the shear
blades for grass shear
Removing the shear blades
1. Remove the grass receiver and place the tool
upside down.
►Fig.10
2. While pressing the lock lever, turn the undercover
counterclockwise until on the undercover is aligned
with on the lock lever.
►Fig.11
3. Removetheundercover,shearblades,andcrank.
►Fig.12: 1.Undercover2.Shearblades3. Crank
Installing the shear blades
1. Preparethecrank,undercover,andnewshear
blades.
►Fig.13: 1. Crank 2.Undercover3.Shearblades
2. Removethebladecoverfromtheoldshear
blades,andthenattachittothenewones.
►Fig.14
3. Adjustthethreepinssothattheyarelinedupon
the alignment line.
►Fig.15: 1.Alignmentline
4. Applyasmallamountofgreasetotheperiphery
ofthecrank.Attachthecranktothepinswiththesmall
andlargeroundsfacingup.
►Fig.16: 1. Crank
5. Adjustthebladesandbaseplatesothatthehole
inthebaseplateandthetwoprotrusionsontheblades
are lined up.
►Fig.17
6. Turntheshearbladesupsidedownandinstall
themsothatthepinsonthetooltintheholeonthe
baseplate.Makesurethattheshearbladesarexed
securely in place.
►Fig.18
7. Placetheundercoversothat on the under-
cover is aligned with on the lock lever.
►Fig.19
8. While pressing the undercover, turn the under-
cover clockwise until on the undercover is aligned
with on the lock lever.
►Fig.20
9. Makesurethatthelocklevertsinthegrooveon
the undercover.
►Fig.21: 1. Lock lever
CAUTION: Never use the tool without install-
ing the undercover.
10. Removethebladecover,andthenturnonthetool
to check that it works properly.
NOTICE: If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing shear blades
for hedge trimmer
Optional accessory
CAUTION: Attach the blade cover before
removing or installing the shear blades.
Removing shear blades
1. Placethetoolupsidedown.
►Fig.22
2. While pressing the lock lever, turn the undercover
counterclockwise until on the undercover is aligned
with on the lock lever.
►Fig.23
3. Remove the undercover.
►Fig.24
4. Loosen two screws with a screwdriver and remove
theshearblades.
►Fig.25: 1. Screws
NOTE:Theshearbladescanberemovedwithout
removing the screws.
5. Removethecrankfromtheshearblades.
►Fig.26: 1. Crank
NOTE:Thecrankmayremaininthetool.
NOTE: Attachthebladecoverandthestoragecaseto
theremovedshearblades,andthenstoretheblades.
Installing shear blades
1. Preparethecrank,undercover,andnewshearblades.
►Fig.27: 1. Crank 2.Undercover3.Shearblades
2. Attachthebladecovertotheshearblades.
►Fig.28
3. Adjustthethreepinssothattheyarelinedupon
the alignment line.

15 ENGLISH
►Fig.29: 1.Alignmentline
4. Applyasmallamountofgreasetotheperipheryof
thecrank.Attachthecranktothepinswithitssmalland
largeroundsfacingdown.
►Fig.30: 1. Crank
5. Slidetheshearbladessothattheholeonthe
baseplateispositionedatthecenteroftheringsof
blades.
►Fig.31
6. Turntheshearbladesupsidedownandinstall
themsothatthepinonthetooltsintheholeonthe
shearblades.Inserttheclawofthebaseplateintothe
grooveonthetool.Makesurethattheshearbladesare
xedsecurelyinplace.
►Fig.32: 1. Claw
7. Tightenthetwoscrewsrmlywithascrewdriver.
►Fig.33: 1. Screws
8. Placetheundercoversothat on the under-
cover is aligned with on the lock lever.
►Fig.34
9. While pressing the undercover, turn the under-
cover clockwise until on the undercover is aligned
with on the lock lever.
►Fig.35
10. Makesurethatthelocklevertsinthegrooveon
the undercover.
►Fig.36: 1. Lock lever
CAUTION: Never use the tool without install-
ing the undercover.
11. Removethebladecover,andthenturnonthetool
tocheckifthetoolworksproperly.
NOTICE: If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing the chip
receiver
Optional accessory
CAUTION: When installing or removing the
chip receiver, always wear gloves and attach the
blade cover so that your hands and face do not
directly contact the blade.
Thechipreceivergathersdiscardedleavesandmakes
clean-upafterwardmucheasier.Itcanbeinstalledon
eithersideofthetool.
Toinstallthechipreceiver,pressitagainsttheshearblades
sothatthehookstintotheholesoftheshearblades.
►Fig.37: 1. Hooks 2. Holes
Toremovethechipreceiver,presstheleversonboth
sides to release the hooks.
►Fig.38: 1. Levers
NOTICE: Never try to remove the chip receiver
by an excessive force with its hooks locked in the
holes of the blades.
OPERATION
WARNING: Before shearing, clear away sticks
and stones from the shearing area. Furthermore, clear
away any weeds from the shearing area in advance.
►Fig.39
WARNING: Keep hands away from blades.
CAUTION: Avoid operating the tool in very
hot weather as much as practicable. When operat-
ing the tool, be careful of your physical condition.
Shearing (for grass shear)
Turnthetoolonafteradjustingtheshearingheightand
holditsothatthebottomofthetoolrestsontheground.
Gentlymovethetoolforward.
►Fig.40
Whentrimmingaroundcurbs,fencesortrees,movethe
toolalongthem.Becarefulthatthebladesdonotcome
into contact with them.
►Fig.41
Whentrimmingsproutsorfoliageofasmalltree,trim
littlebylittle.
►Fig.42
Trimlargebranchestothedesiredheightusingbranch
cuttersbeforeusingthistool.
NOTICE: Do not use the tool in a way that causes
the motor to stop or to rotate extremely slowly.
NOTICE: Do not attempt to cut thick branches.
NOTICE: Do not allow the shear blades to con-
tact the ground during operation. The blades will
be dulled, causing poor performance.
NOTICE: Do not trim the wet grass or foliage of
small trees.
Cutting long lawn
Do not try to cut long grass all at once. Instead, cut the
lawninsteps.Leaveadayortwobetweencutsuntilthe
lawnbecomesevenlyshort.
►Fig.43
NOTE: Cutting long grass to a short length all at once
may cause the grass to die.
Trimming (for hedge trimmer)
CAUTION: Be careful not to accidentally
contact a metal fence or other hard objects while
trimming.Thebladesmaybreakandcauseaninjury.
CAUTION: Be careful not to allow the shear
blades to contact the ground.Thetoolmayrecoil
andcauseaninjury.

16 ENGLISH
CAUTION: Overreaching with a hedge trim-
mer, particularly from a ladder, is extremely
dangerous. Do not work while standing on anything
wobblyorinrm.
NOTICE: Do not attempt to cut branches thicker
than 10 mm in diameter with the tool.Cutbranches
tothedesiredheightusingbranchcuttersbefore
using the tool.
NOTICE: Do not cut down dead trees or similar
hard objects. Doing so may damage the tool.
NOTICE: Do not trim the grass or weeds while
using the shear blades.Thebladesmaybecome
tangled in the grass or weeds.
Hold the tool with one hand, pull the switch trigger while
pressingthelock-offbutton,andthenmoveitforward.
►Fig.44
Forbasicoperation,tiltthebladestowardthetrimming
direction and move it calmly and slowly at the speed
rateof3to4secondspermeter.
►Fig.45
Totieastringatthedesiredheightandtotrimalongit
help you to cut a hedge top evenly.
►Fig.46
Ifthechipreceiverisattachedtotheblades,itgathers
discardedleavesandmakesclean-upafterwardmuch
easier.
Tocutahedgesideevenly,cutfromthebottomtotop.
►Fig.47
Whentrimmingtomakearoundshape(trimmingbox-
woodorrhododendron,etc.),trimfromtheroottothe
topforabeautifulnish.
►Fig.48
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers,alwaysusingMakitareplacementparts.
Cleaning the tool
Cleanthetoolbywipingoffdustwithadryclothorone
dipped in soapy water and wrung out.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Blade maintenance
Beforetheoperationoronceperhourduringoperation,
applylow-viscosityoil(machineoil,orspray-typelubri-
catingoil)totheblades.
►Fig.49
►Fig.50
Afteroperation,removedustfrombothsidesofthe
bladeswithawiredbrush,wipeitoffwithaclothand
then apply low-viscosity oil (machine oil, or spray-type
lubricatingoil)totheblades.
►Fig.51
►Fig.52
NOTICE: Do not wash the blades in water. Doing
so may cause rust or damage to the tool.
NOTICE: Dirt and corrosion cause excessive
blade friction and shorten the operating time per
battery charge.
Storage
Thehookholeinthetoolbottomisconvenientforhang-
ingthetoolfromanailorscrewonthewall.
Attachthebladecovertotheshearbladessothatthe
bladesarenotexposed.Storethetooloutofthereach
ofchildren.Storethetoolinaplacenotexposedto
moisture or rain.
►Fig.53: 1. Hole
►Fig.54: 1. Hole
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual.Theuseofanyother
accessoriesorattachmentsmightpresentariskof
injurytopersons.Onlyuseaccessoryorattachment
foritsstatedpurpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Shearbladeassembly(forgrassshearuse)
• Shearbladecover(forgrassshearuse)
• Grassreceiver(forgrassshearuse)
• Longhandleattachment(forgrassshearuse)
• Shearbladeassembly(forhedgetrimmeruse)
• Shearbladecover(forhedgetrimmeruse)
• Chipreceiver(forhedgetrimmeruse)
• Storagecase
• Makitagenuinebatteryandcharger
NOTE:Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.Theymay
differfromcountrytocountry.

17 SLOVENŠČINA
SLOVENŠČINA (Originalna navodila)
TEHNIČNI PODATKI
Model: UM603D
Širinareza 160 mm
Hodi na minuto 2.500 min-1
Mere
(D × Š × V)
343 mm × 177 mm × 131 mm
Nazivnanapetost D.C. 18 V
Akumulatorskabaterija BL1815G
Netoteža 1,5 kg
• Kernenehnoopravljamoraziskaveinrazvijamosvojeizdelke,selahkotehničnipodatkivtemdokumentu
spremenijobrezobvestila.
• Tehničnipodatkiinbaterijskivložkiselahkorazlikujejogledenadržavouporabeizdelka.
• TežaskupajzbaterijskimvložkomvskladuspostopkomEPTA01/2003
Simboli
Naslednjisimboliseuporabljajovpovezavisstrojem.
Preduporaboizdelkaseobveznoseznaniteznjihovim
pomenom.
Potrebnajeposebnapozornostin
previdnost.
Preberitenavodilazauporabo.
Nevarnost;paziteseletečihpredmetov.
Nedovoliteosebam,dasepribližajo.
Komotorugasnete,serezilaševedno
premikajo.
Neizpostavljajtevlagi.
Cd
Ni-MH
Li-ion
SamozadržaveEU
Nezavrziteizrabljeneelektričneopremeali
akumulatorskegasklopamedgospodinjske
odpadke!
VskladuzEvropskimidirektivamio
odpadnielektričniinelektronskiopremi,
baterijahinakumulatorjih,odpadnihbate-
rijahinakumulatorjihterupoštevanjem
njihovihdoločilvskladuzdržavnozako-
nodajojetrebaelektričnoopremo,baterije
inakumulatorje,katerihživljenjskicikel
jepretekel,zbiratiločenoinjihdostaviti
vustrezenobratzarecikliranje,kideluje
skladnozokoljevarstvenimizahtevami.
Predvidena uporaba
Orodjejenamenjenorezanjurobovtratealimladik.
Hrup
ObičajnaA-ovrednotenaravenhrupavskladuz
EN50636:
UM603D z nameščenim rezilom škarij za travo
Ravenzvočnegatlaka(LpA):76dB(A)
Odstopanje(K):1,82dB(A)
Nivohrupameddelomlahkopreseže80dB(A).
OPOZORILO: Uporabljajte zaščito za sluh.
ObičajnaA-ovrednotenaravenhrupavskladuz
EN60745:
UM603D z nameščenim rezilom rezalnika za živo
mejo
Ravenzvočnegatlaka(LpA):74dB(A)
Odstopanje(K):3dB(A)
Nivohrupameddelomlahkopreseže80dB(A).
OPOZORILO: Uporabljajte zaščito za sluh.
Vibracije
Skupnevrednostivibracij(vektorskavsotatrehosi)v
skladuzEN50636:
UM603D z nameščenim rezilom škarij za travo
Emisijevibracij(ah):2,5m/s2alimanj
Odstopanje(K):1,5m/s2
Skupnevrednostivibracij(vektorskavsotatrehosi)v
skladuzEN60745:
UM603D z nameščenim rezilom rezalnika za živo
mejo
Emisijevibracij(ah):2,5m/s2alimanj
Odstopanje(K):1,5m/s2
OPOMBA:Navedenavrednostoddajanjavibracij
jebilaizmerjenavskladusstandardnimimetodami
testiranjainselahkouporabljazaprimerjavoorodij.
OPOMBA:Navedenavrednostoddajanjavibra-
cijselahkouporabljatudipripredhodnioceni
izpostavljenosti.

18 SLOVENŠČINA
OPOZORILO: Oddajanjevibracijmeddejansko
uporaboelektričnegaorodjaselahkorazlikujeodnavedene
vrednostioddajanja,odvisnoodnačinauporabeorodja.
OPOZORILO: Upravljavecmorazalastnozaščito
poznativarnostneukrepe,kitemeljijonaoceniizpostavlje-
nostivdejanskihpogojihuporabe(polegčasaproženjaje
trebaupoštevaticelotendelovnicikel,vključnosčasom,ko
jeorodjeizklopljeno,inčasom,kodelujevprostemteku).
Izjava o skladnosti ES
Samo za evropske države
IzjavaESoskladnostijevključenavdodatkuA,kije
priložentemnavodilomzauporabo.
VARNOSTNA
OPOZORILA
Splošna varnostna opozorila za
električno orodje
OPOZORILO: Preberite vsa varnostna opozo-
rila in navodila s slikami in tehničnimi podatki, ki so
dobavljeni skupaj z električnim orodjem.Obneupo-
števanjuspodajnavedenihnavodilobstajanevarnost
električnegaudara,požarain/alihudihtelesnihpoškodb.
Shranite vsa opozorila in navo-
dila za poznejšo uporabo.
Izraz„električnoorodje“vopozorilihsenanašanavaše
električnoorodje(skablom)alibaterijskoelektrično
orodje(brezkabla).
Varnostna opozorila za brezžične
škarje za travo
Splošna navodila
1.
Za zagotavljanje pravilnega delovanja mora upo-
rabnik prebrati ta navodila za uporabo in se sez-
naniti z upravljanjem opreme.Nezadostnopoučeni
uporabnikilahkospravijovnevarnostsebeinokolico.
2. Nikoli ne dovolite uporabe orodja otrokom, ose-
bam z zmanjšanimi zičnimi, čutilnimi ali psihič-
nimi sposobnostmi ter s pomanjkanjem izkušenj
in znanja ter osebam, ki niso seznanjene s temi
navodili za uporabo orodja. Lokalni predpisi
lahko omejijo starost upravljavca.
3. Opremo uporabljajte samo, ko ste popolnoma
zbrani in pozorni.
4.
Z opremo delajte samo, če ste v dobri zični kondi-
ciji. Vsa dela opravljajte mirno in zbrano. Uporabljajte
zdrav razum in upoštevajte, da je upravljavec ali
uporabnik odgovoren za nesreče ali nevarnosti, ki se
zgodijo drugim ljudem ali njihovi lastnini.
5. Nikoli ne uporabljajte orodja v bližini ljudi, še
posebej otrok, ali hišnih ljubljenčkov.
6. V primeru težav ali neobičajnih znakov opreme
takoj ugasnite motor.
7.
Med počitkom in kadar puščate opremo nenadzo-
rovano, jo ugasnite in odstranite akumulatorsko
baterijo ter jo odložite na varno mesto, da preprečite
nevarnost za druge osebe ali poškodbe opreme.
8. Orodja ne uporabljajte v slabem vremenu, še
posebej, kadar bliska.
Osebna zaščitna oprema
1. Med uporabo orodja vedno nosite zaščito za
oči in robustne čevlje.
2. Pri delu z orodjem vedno nosite kakovostno
obutev in dolge hlače.
Zagon opreme
1.
Zagotovite, da se v bližini ne nahajajo otroci ali druge
osebe. Pazite tudi na živali, ki se nahajajo v delovnem
območju.Sicerprenehajtezuporaboopreme.
2. Pred uporabo vedno preverite, ali je oprema
varna za uporabo. Preverite varnost rezal-
nega orodja in ščitnika ter sprožilca/sprožilne
ročice, da zagotovite enostavno in pravilno
uporabo. Preverite, ali so ročaji čisti in suhi,
ter preizkusite delovanje vklopa/izklopa.
3.
Pred nadaljnjo uporabo opreme preverite poško-
dovane dele. Ščitnik ali drug poškodovan del je
treba skrbno pregledati, da ugotovite, ali bo pra-
vilno deloval in služil svojemu namenu. Preverite
poravnanost in zatikanje gibljivih delov, more-
bitne zlomljene dele in vsa druga stanja, ki bi
lahko vplivala na njegovo delovanje. Ščitnik ali
drug poškodovani del mora ustrezno popraviti
ali zamenjati pooblaščeni servisni center, razen
če je drugače določeno v teh navodilih.
4. Motor vključite samo, če roke in noge niso v
bližini rezalnega orodja.
5. Pred zagonom se prepričajte, da rezalno
orodje ni v stiku z drugimi predmeti.
Način uporabe
1. Opremo uporabljajte samo pri dobri svetlobi
in vidljivosti. Pozimi bodite pozorni na drseča
ali mokra območja ter led in sneg (nevarnost
zdrsa). Na nagnjenih površinah morate vedno
biti pozorni, da stojite trdno na tleh. Med upo-
rabo orodja ne tecite, temveč hodite.
2. Bodite previdni, da si z rezalnim orodjem ne
poškodujete stopal in dlani.
3. Med uporabo opreme nikoli ne stojte na lestvi.
4.
Med rezanjem z opremo nikoli ne plezajte na drevesa.
5. Nikoli ne delajte na nestabilnih površinah.
6.
Iz delovnega območja odstranite pesek, kamne,
žeblje itd.Tujidelcilahkopoškodujejorezalno
orodjeinpovzročijonevarnepovratneudarce.
7. Če rezalno orodje zadene ob kamne ali
druge trde predmete, takoj izklopite motor in
preglejte rezalno orodje.
8. Pregledujte rezalno orodje v krajših in rednih
presledkih (odkrivanje razpok širine lasu z
uporabo metode trkanja).
9. Pred začetkom rezanja mora rezalno orodje
doseči polno delovno hitrost.
10.
Rezalno orodje mora biti opremljeno z ustreznim
ščitnikom. Nikoli ne uporabljajte opreme s poško-
dovanimi ščitniki ali brez nameščenih ščitnikov!
11. Med uporabo orodja morate uporabljati vso zašči-
tno opremo in ščitnike, ki so priloženi opremi.

19 SLOVENŠČINA
12.
Vedno odstranite akumulatorsko baterijo iz opreme:
— kadar pustite opremo nenadzorovano,
— preden odstranite oviro,
— pred pregledom, čiščenjem ali delom na
opremi,
— po odstranitvi tujka,
— kadar oprema začne neobičajno vibrirati.
13. Poskrbite, da v odprtinah za prezračevanje
nikoli ni smeti.
14.
Ko motor ugasnete, se rezila še vedno premikajo.
Rezalno orodje
Uporabljajte ustrezno rezalno orodje za delo,
ki ga opravljate.
Navodila za vzdrževanje
1.
Pred začetkom dela je treba preveriti stanje opreme,
predvsem zaščitnih naprav rezalnega orodja.
2. Pred izvajanjem vzdrževanja, zamenjavo rezalnega
orodja ali čiščenjem opreme ali rezalnega orodja
ugasnite motor in odstranite akumulatorsko baterijo.
3. Kadar opreme ne uporabljate, jo shranite v
notranjem, suhem prostoru na visokem mestu
ali v zaklenjenem vsebniku zunaj dosega otrok.
Pred hrambo jo očistite in izvedite vzdrževanje.
SHRANITE TA NAVODILA.
OPOZORILO: NE dovolite, da bi zaradi udob-
nejšega dela ali znanja o uporabi izdelka (prido-
bljenega z večkratno uporabo) opustili strogo
upoštevanje varnostnih zahtev v okviru pravilne
uporabe orodja. ZLORABA ali neupoštevanje var-
nostnih zahtev v teh navodilih za uporabo lahko
povzroči resne telesne poškodbe.
Varnostna opozorila za brezžični
rezalnik za živo mejo
1. Ne približujte delov telesa rezilu kose. Ne
odstranjujte odrezanega materiala in ne držite
materiala, ki ga boste rezali, kadar se rezila
premikajo. Kadar čistite zataknjen material, se
prepričajte, da je stikalo izklopljeno.Trenutek
nepazljivostiprideluzrezalnikomzaživomejo
lahkoprivededohudihtelesnihpoškodb.
2.
Rezalnik za živo mejo nosite tako, da ga držite za
ročaj, rezila kose pa so ustavljena. Kadar prena-
šate ali shranjujete rezalnik za živo mejo, vedno
namestite pokrov rezalne naprave.Ustrezno
rokovanjezrezalnikomzaživomejobozmanjšalo
morebitnetelesnepoškodbezaradirezil.
3. Držite električno orodje na izoliranih držalnih
površinah, saj lahko rezilo kose prereže skrito
električno napeljavo.Čeprerežetevodnike
podnapetostjo,sopodnapetostjovsineizolirani
kovinskidelielektričnegaorodja,zaradičesar
lahkoupravljavecutrpielektričniudar.
4.
Rezalnika za živo mejo ne uporabljajte v dežju ali v
zelo vlažnih pogojih.Električnimotornivodotesen.
5. Uporabnike, ki prvič uporabljajo rezalnik za živo
mejo, naj izkušeni uporabnik pouči o uporabi orodja.
6. Rezalnika za živo mejo ne smejo uporabljati
otroci ali mlajši od 18 let.Mladoletneosebe,
starejšeod16let,solahkoizvzeteizteomejitve,
česeusposabljajopodnadzoromstrokovnjaka.
7.
Z rezalnikom za živo mejo delajte samo, če ste v dobri
zični kondiciji.Česteutrujeni,bovašazbranostzmanj-
šana.Šeposebejboditepozorniobkoncudelovnegadne.
Vsadelaopravljajtemirnoinzbrano.Uporabnikjeodgovo-
renzavsepoškodbe,povzročenetretjimosebam.
8. Nikoli ne uporabljajte rezalnika pod vplivom
alkohola, drog ali zdravil.
9. Delovne rokavice iz robustnega usnja so del
osnovne opreme rezalnika za živo mejo in jih
je pri delu treba vedno nositi. Prav tako nosite
močne čevlje z nedrsečim podplatom.
10.
Pred začetkom dela se prepričajte, da je rezalnik v
dobrem in varnem stanju za delo. Zagotovite, da so
ščitniki pravilno nameščeni. Rezalnika za živo mejo
ni dovoljeno uporabljati, če ni v celoti sestavljen.
11. Pred začetkom uporabe zagotovite trdno stojišče.
12. Med uporabo trdno držite orodje.
13. Ne uporabljajte orodja brez obremenitve po
nepotrebnem.
14.
Če rezalnik pride v stik z ograjo ali drugim trdim
predmetom, takoj ugasnite motor in odstranite
akumulatorsko baterijo. Preverite, ali je rezalnik
poškodovan, in ga v tem primeru takoj popravite.
15. Preden rezalnik pregledate, odpravite napake ali
odstranite material, ki se je ujel v rezalnik, vedno
izklopite rezalnik in odstranite akumulatorsko baterijo.
16. Pred vzdrževalnimi deli izklopite rezalnik in
odstranite akumulatorsko baterijo.
17.
Kadar prenašate rezalnik za živo mejo na drugo
lokacijo, tudi med delom, vedno odstranite aku-
mulatorsko baterijo in namestite pokrov rezila.
Nikoli ne prenašajte ali prevažajte rezalnika, kadar
deluje. Nikoli ne prijemajte rezalnika z rokami.
18. Po uporabi in preden shranite rezalnik za
živo mejo za dlje časa ga očistite (še posebej
rezilo). Rahlo naoljite rezalnik in namestite
pokrov.Pokrov,kijepriloženenoti,lahkoobesite
nasteno,karomogočavareninpraktičennačin
shranjevanjarezalnikazaživomejo.
19.
Rezalnik za živo mejo shranjujte z nameščenim pokro-
vom in v suhem prostoru. Shranjujte nedosegljivo
otrokom. Rezalnika nikoli ne shranjujte na prostem.
SHRANITE TA NAVODILA.
OPOZORILO: NE dovolite, da bi zaradi udob-
nejšega dela ali znanja o uporabi izdelka (prido-
bljenega z večkratno uporabo) opustili strogo
upoštevanje varnostnih zahtev v okviru pravilne
uporabe orodja. ZLORABA ali neupoštevanje var-
nostnih zahtev v teh navodilih za uporabo lahko
povzroči resne telesne poškodbe.
Pomembna varnostna navodila za
akumulatorsko baterijo
1. Pred uporabo baterijskega vložka preberite
vsa navodila in opozorilne oznake na (1) pol-
nilniku akumulatorja, (2) akumulatorju in (3)
izdelku, ki uporablja akumulator.
2. Ne razstavljajte baterijskega vložka.
3. Če se je čas delovanja občutno skrajšal, takoj
prenehajte uporabljati orodje. V nasprotnem
primeru lahko pride do pregretja, morebitnih
opeklin in celo eksplozije.

20 SLOVENŠČINA
4. Če pride elektrolit v stik z očmi, jih sperite s
čisto vodo in takoj poiščite zdravniško pomoč.
Posledica je lahko izguba vida.
5. Ne povzročite kratkega stika baterijskega
vložka:
(1) Ne dotikajte se priključkov s kakršnim
koli prevodnim materialom.
(2) Izogibajte se shranjevanju baterijskega
vložka v vsebniku z drugimi kovinskimi
predmeti kot so žeblji, kovanci itn.
(3) Ne izpostavljajte baterijskega vložka vodi
ali dežju.
Kratek stik akumulatorja lahko povzroči velik
električni tok, pregrevanje, morebitne opekline
in celo okvaro.
6. Ne shranjujte orodja in baterijskega vložka
na mestih, kjer lahko temperatura doseže ali
preseže 50 °C.
7. Ne sežigajte baterijskega vložka, tudi če je
hudo poškodovan ali v celoti izpraznjen.
Baterijski vložek lahko v ognju eksplodira.
8. Poskrbite, da akumulator ne bo izpostavljen
padcem ali udarcem.
9. Ne uporabljajte poškodovanih akumulatorjev.
10. Priložene litij-ionske baterije ustrezajo zahte-
vam zakonodaje v zvezi z nevarnim blagom.
Zakomercialneprevoze,npr.tiste,kijihopravljajo
tretjestrankeincarinskiposredniki,jetrebaupo-
števatiposebnezahtevevzvezizembalažoin
označevanjem.
Medpostopkompripravenaodpremoizdelkase
jetrebaposvetovatisstrokovnjakomzanevarne
snovi.Pritemupoštevajtetudipodrobnejšenacio-
nalne predpise.
Odprtestikeoblepitezlepilnimtrakomalijihdru-
gačezaščitite,baterijopazapakirajtetako,dasev
embalažinemorepremikati.
11. Upoštevajte lokalne uredbe glede odlaganja
akumulatorja.
SHRANITE TA NAVODILA.
POZOR: Uporabljajte le originalne baterije
Makita.ČeuporabljateneoriginalnebaterijeMakita
alibaterije,kisobilespremenjene,lahkopridedo
eksplozijebaterijeinposledičnodopožara,telesnih
poškodbalimaterialneškode.Stakšnouporabo
bostetudirazveljaviligarancijoMakitazaorodjein
polnilnikMakita.
Nasveti za ohranjanje največje
zmogljivosti akumulatorja
1. Napolnite baterijski vložek, preden se v celoti
izprazni. Ko opazite, da ima orodje manjšo
moč, vedno ustavite delovanje orodja in napol-
nite baterijski vložek.
2. Nikoli znova ne polnite popolnoma napol-
njenega baterijskega vložka. Prenapolnjenje
skrajša življenjsko dobo akumulatorja.
3. Baterijski vložek s sobno temperaturo pol-
nite pri temperaturi okolja od 10 °C do 40 °C.
Počakajte, da se vroč baterijski vložek pred
polnjenjem ohladi.
OPIS DELOVANJA
POZOR: Pred nastavljanjem ali preizkusom
delovanja orodja se prepričajte, ali je orodje
izključeno in ali je akumulatorska baterija
odstranjena.
Uporaba orodja kot brezžični
rezalnik za živo mejo
Orodjelahkouporabljatekotbrezžičnirezalnikzaživo
mejo,takodanamestiterezilarezalnikazaživomejo
(dodatna oprema).
Nameščanje ali odstranjevanje
akumulatorske baterije
POZOR: Vedno izklopite orodje, preden name-
stite ali odstranite akumulatorsko baterijo.
POZOR: Kadar nameščate ali odstranjujete
akumulatorsko baterijo, trdno držite orodje in
akumulatorsko baterijo.Čeorodjainakumulatorske
baterijenedržitetrdno,selahkozgodi,davamzdr-
snetaizrok,posledicapajelahkopoškodbaorodjain
akumulatorskebaterijetertelesnapoškodba.
►Sl.1: 1.Rdečiindikator2.Gumb3.Baterijskivložek
Čeželiteodstranitiakumulatorskobaterijo,jopotisnite
izorodja,pritempapomikajtegumbnasprednjistrani
vložka.
Akumulatorskobaterijovstavitetako,daporavnate
jezičeknabaterijizutoromnaohišjuinjopotisnetev
ležišče.Potisnitejodokonca,dasezaskoči.Čejerdeči
indikatornazgornjistranigumbaviden,pomeni,da
baterijaniustreznozaklenjena.
POZOR: Vedno namestite akumulatorsko
baterijo tako, da rdeči indikator ni več viden.Če
teganeupoštevate,lahkobaterijanepričakovano
padeizorodjainpoškodujevasaliosebevneposre-
dnibližini.
POZOR: Ne nameščajte akumulatorske bate-
rije s silo.Česeakumulatorskabaterijanezaskoči
zlahka,nipravilnovstavljena.
Zaščitni sistem orodja/akumulatorja
Orodjejeopremljenozzaščitnimsistemomzaorodje/
akumulator.Sistemsamodejnoprekinenapajanje
orodja,dapodaljšaživljenjskodoboorodjainakumula-
torja.Orodjesesamodejnozaustavimeddelovanjem,
čeorodjealiakumulatordelujetapodnaslednjimi
pogoji:
Zaščita pred preobremenitvijo
Kadarakumulatoruporabljatenanačin,kipovzroča
uporaboneobičajnovisokegatoka,seorodjesamo-
dejnoustavi.Vtemprimeruizklopiteorodjeinprekinite
delo,kijepovzročilopreobremenitevorodja.Natovklo-
piteorodje,dagaznovazaženete.