Makita DLM460 User manual

DLM460
DLM461
EN Cordless Lawn Mower INSTRUCTION MANUAL 7
ID Mesin Pemotong Rumput
Tanpa Kabel PETUNJUK PENGGUNAAN 17
VI Máy Cắt Cỏ Đẩy Cầm Tay
Hoạt Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 28
TH   38

1
2
3
6
5
4
Fig.1
1
2
3
6
45
Fig.2
12
3
Fig.3
1
Fig.4
1
2
Fig.5
1
Fig.6
2

1
2
Fig.7
1
Fig.8
13
2
Fig.9
Fig.10
1
2
Fig.11
1
2
Fig.12
1
2
Fig.13
1
2
Fig.14
3

1
2
Fig.15
1
Fig.16
1
Fig.17
1
2
Fig.18
2 31
4
5 6
Fig.19
1
3
2
Fig.20
1
Fig.21
4

1
2
Fig.22
1
2
3
21
Fig.23
1
2
Fig.24
Fig.25
Fig.26
12
33
Fig.27
Fig.28
5

Fig.29
1 2
3
Fig.30
1
2
Fig.31
1
3
2
Fig.32
1
2
2
Fig.33
1
2
3
Fig.34
1
2
3
Fig.35
6

7ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DLM460 DLM461
Mowing width (blade diameter) 460 mm
No load speed 2,500 min-1
Maximum speed 3,300 min-1
Part number of replacement mower blade 199367-2
Dimensions
(L x W x H)
during operation L: 1,319 mm to 1,518 mm
W: 532 mm
H: 879 mm to 1,138 mm
when stored
(without grass basket)
L: 1,004 mm to 1,125 mm
W: 532 mm
H: 533 mm to 713 mm
Rated voltage D.C. 36 V
Net weight 25.3 - 27.6 kg 25.2 - 27.2 kg
Protection degree IPX4
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsandbatterycartridgemaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860B
• Someofthebatterycartridgeslistedabovemaynotbeavailabledependingonyourregionofresidence.
WARNING: Only use the battery cartridges listed above.Useofanyotherbatterycartridgesmaycause
injuryand/orre.
Symbols
Thefollowingsshowthesymbolsusedfortheequip-
ment.Besurethatyouunderstandtheirmeaningbefore
use.
Take particular care and attention.
Read instruction manual.
Danger;beawareofthrownobjects.
The distance between the tool and
bystandersmustbeatleast15m.
Neverputyourhandsandfeetnearthe
blade under the mower. Blades continue to
rotateafterthemotorisswitchedo󰀨.
Removethelockkeybeforeinspecting,
adjusting,cleaning,servicing,leavingand
storing the mower.
Ni-MH
Li-ion
OnlyforEUcountries
Donotdisposeofelectricequipmentor
batterypacktogetherwithhouseholdwaste
material!
In observance of the European Directives,
on Waste Electric and Electronic
EquipmentandBatteriesandAccumulators
and Waste Batteries and Accumulators
and their implementation in accordance
withnationallaws,electricequipmentand
batteriesandbatterypack(s)thathave
reached the end of their life must be col-
lectedseparatelyandreturnedtoanenvi-
ronmentallycompatiblerecyclingfacility.
Intended use
The machine is intended for lawn mowing.
SAFETY WARNINGS
Lawn Mower Safety Instructions
WARNING: Read all safety warnings and
all instructions. Failure to follow the warnings and
instructionsmayresultinelectricshock,reand/or
seriousinjury.

8ENGLISH
Save all warnings and instruc-
tions for future reference.
1. Do not insert the lock key into mower until it is
ready to be used.
2. Children should be supervised to ensure that
they do not play with the mower.
3. Never allow children or people unfamiliar with
these instructions to use the mower. Local
regulations can restrict the age of the operator.
4. Never operate the mower while people, espe-
cially children, or pets are nearby.
5. Keep in mind that the operator or user is
responsible for accidents or hazards occurring
to other people or their property.
6. While operating the mower, always wear sub-
stantial footwear and long trousers. Do not
operate the mower when barefoot or wearing
open sandals. Avoid wearing clothing or jew-
elry that is loose tting or that has hanging
cords or ties. They can be caught in moving
parts.
7. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
8. Operate the mower only in daylight or in good
articial light.
9. Avoid operating the mower in wet grass.
10. Battery tool use and care
- Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
onetypeofbatterycartridgemaycreateariskof
rewhenusedwithanotherbatterycartridge.
- Use power tools only with specically desig-
nated battery cartridges.Useofanyotherbat-
terycartridgesmaycreateariskofinjuryandre.
- When battery cartridge is not in use, keep
it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the bat-
teryterminalstogethermaycauseburnsorare.
- Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritation or burns.
- Do not dispose of the battery(ies) in a re.
Thecellmayexplode.Checkwithlocalcodesfor
possible special disposal instructions.
- Do not open or mutilate the battery(ies).
Releasedelectrolyteiscorrosiveandmaycause
damagetotheeyesorskin.Itmaybetoxicif
swallowed.
- Do not charge battery in rain, or in wet
locations.
11. Always keep a rm hold on the handle.
12. Always be sure of your footing on slopes.
13. Walk, never run.
14. Don't grasp the exposed cutting blades or
cutting edges when picking up or holding the
mower.
15. Physical condition - Do not operate mower
while under the inuence of drugs, alcohol, or
any medication.
16. Keep hands and feet away from rotating
blades. Caution - Blades coast after the mower
is switched o󰀨.
17. Use only the manufacturer genuine blades
specied in this manual.
18. Check the blades or blade bolts carefully for
cracks or damage before operation. Replace
cracked or damaged blades or blade bolts
immediately.
19. Be sure the area is clear of other people before
mowing. Stop mower if anyone enters the area.
20. Remove foreign matters such as rocks, wire,
bottles, bones and large sticks from the work
area before mowing to prevent personal injury
or damage to the mower.
21. Stop operation immediately if you notice
anything unusual. Switch o󰀨 the mower and
remove the key. Then inspect the mower.
22. Never attempt to make cutting height adjust-
ments while mower is running if the mower
has cutting height adjustment feature.
23. Release switch lever and wait for blade rota-
tion to stop before crossing driveways, walks,
roads, and any gravel-covered areas. Also
remove the lock key if you leave the mower,
reach to pick up or remove something out of
your way, or for any other reason that may
distract you from what you are doing.
24. Objects struck by the mower blade can cause
severe injuries to persons. The lawn should
always be carefully examined and cleared of
all objects prior to each mowing.
25. If the mower strikes a foreign object, follow
these steps:
- Stop the mower, release the switch lever and
wait until the blade comes to a complete stop.
- Remove the lock key and the battery
cartridge.
- Thoroughly inspect the mower for any
damage.

9ENGLISH
- Replace the blade if it is damaged in any way.
Repair any damage before restarting and con-
tinuing to operate the mower.
26. Check the grass basket frequently for wear or
deterioration. For storage, always make sure
the grass basket is empty. Replace a worn
grass basket with a new factory replacement
for safety.
27. Use extreme caution when reversing or pulling
the mower towards you.
28. Stop the blade(s) if the mower has to be tilted
for transportation when crossing surfaces
other than grass, and when transporting the
mower to and from the area to be used.
29. Never operate the mower with defective
guards or shields, or without safety devices,
for example deectors and/or grass basket, in
place.
30. Switch on the mower carefully according to
instructions and with feet well away from the
blade(s).
31. Do not tilt the mower when switching on the
motor, except if the mower has to be tilted for
starting. In this case, do not tilt it more than
absolutely necessary and lift only the part,
which is away from the operator.
32. Do not start the mower when standing in front
of the discharge opening.
33. Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at
all times.
34. Do not transport the mower while the mower is
turned on.
35. Stop the mower, and remove the disabling
device. Make sure that all moving parts have
come to a complete stop
- whenever you leave the mower,
- before clearing blockages or unclogging
chute,
- before checking, cleaning or working on the
mower,
- after striking a foreign object. Inspect the
mower for damage and make repairs before
restarting and operating the mower.
36. If the mower starts to vibrate abnormally
(check immediately)
- inspect for damage,
- replace or repair any damaged parts,
- check for and tighten any loose parts.
37. Be careful during adjustment of the mower
to prevent entrapment of the ngers between
moving blades and xed parts of the mower.
38. Mow across the face of slopes, never up and
down. Exercise extreme caution when chang-
ing direction on slopes. Do not mow exces-
sively steep slopes.
39. Check the blade mounting bolt at frequent
intervals for proper tightness.
40. Keep all nuts, bolts, and screws tight to
be sure the equipment is in safe working
condition.
41. Always allow the mower to cool down before
storing.
42. When servicing the blades be aware that, even
though the power source is switched o󰀨, the
blades can still be moved.
43. Replace worn or damaged parts for safety.
Use only genuine replacement parts and
accessories.
44. Do not use the machine when there is a risk of
lightning.
45. When you use the machine on muddy ground,
wet slope, or slippery place, pay attention to
your footing.
46. Avoid working in poor environment where
increased user fatigue is expected.
47. Do not use the machine in bad weather where
visibility is limited.Failuretodosomaycause
fallorincorrectoperationduetolowvisibility.
48. Do not replace the battery in the rain.
49. Do not submerge the machine into a puddle.
50. Do not leave the machine unattended outdoors
in the rain.
51. Do not insert or remove the lock key in the
rain.
52. When wet leaves or dirt adhere to the suc-
tion mouth (ventilation window) due to rain,
remove them.
53. Do not wash the machine with high pressure
water.
54. When washing the machine, be sure to remove
the battery and lock key and close the battery
cover, and pour water toward the bottom of the
machine to which the blade is attached.
55. When storing the machine, avoid direct sun-
light and rain, and store it in a place where it
does not get hot or humid.
56. Perform inspection or maintenance in a place
where rain can be avoided.
57. After using the machine, remove the adhered
dirt and dry the machine completely before
storing. Depending on the season or the area,
there is a risk of malfunction due to freezing.
58. Do not wet the terminal of battery with liquid
such as water, or submerge the battery. Do not
leave the battery in the rain, nor charge, use,
or store the battery in a damp or wet place. If
theterminalgetswetorliquidentersinsideofbat-
tery,thebatterymaybeshortcircuitedandthereis
ariskofoverheat,re,orexplosion.
59. After removing the battery from the machine or
charger, be sure to attach the battery cover to
the battery and store it in a dry place.
60. Do not replace the battery with wet hands.
61. Do not use the machine in the snow.
62. If the cut-o󰀨 grass is wet, it is likely to be
clogged inside of the machine. Check the con-
dition of the machine regularly, and remove the
adhered grass as necessary.
SAVE THESE INSTRUCTIONS.

10 ENGLISH
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwardingagents,specialrequirementonpack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
inganexpertforhazardousmaterialisrequired.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tapeormasko󰀨opencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).
ASSEMBLY
WARNING: Always be sure that the lock key
and battery cartridge are removed before carrying
out any work on the mower. Failure to remove the
lockkeyandthebatterycartridgemayresultinseri-
ouspersonalinjuryfromaccidentalstart-up.
WARNING: Never start the mower unless it is
completely assembled. Operation of the machine
inapartiallyassembledstatemayresultinserious
personalinjuryfromaccidentalstart-up.
Installing the handle
NOTICE: When installing handles, position the
cords so that they are not caught by anything
between the handles. If the cord is damaged, the
mower switch may not work.
1. Attach the lower handle so that the holes in the
handletintheprotrusionsonthemowerbody.Insert
the bolts from inside, then attach washer A from outside,
and then tighten the thumb nuts.
►Fig.1: 1. Lower handle 2. Washer A 3. Thumb nut
4. Protrusion 5. Hole 6. Bolt

11 ENGLISH
2. Align the hole in the lower handle with the hole
in the upper handle, then insert the bolts from inside,
then attach washer B from outside, and then tighten the
thumb nuts.
►Fig.2: 1. Upper handle 2. Hole 3. Washer B
4. Thumb nut 5. Lower handle 6. Bolt
CAUTION: Hold the upper handle rmly so
that it does not drop o󰀨 your hand. Otherwise, the
handlemayfallandcauseaninjury.
3. Attach holder A and holder B to the handle.
Positionthecordsasshowninthegure.
►Fig.3: 1. Cord 2. Holder A 3. Holder B
NOTE: When attaching holder A, be sure to x the
cord with the holder as shown in the gure.
Removing the mulching attachment
For DLM460
1. Open the rear cover.
►Fig.4: 1. Rear cover
2. Remove the mulching attachment while holding
down the lever.
►Fig.5: 1. Lever 2. Mulching attachment
For DLM461
1. Open the rear cover.
►Fig.6: 1. Rear cover
2. Remove the mulching attachment while pulling the
lever.
►Fig.7: 1. Mulching attachment 2. Lever
Installing the grass basket
1. Open the rear cover.
►Fig.8: 1. Rear cover
2. Hook the grass basket on the rod of the mower
bodyasshowninthegure.
►Fig.9: 1. Rod 2. Guard 3. Grass basket
NOTICE: Make sure that the guard on the grass
basket is facing downward. Otherwise, the grass
basketmaynotcatchallofcut-o󰀨grass.
For DLM461
CAUTION: Be sure to install the grass basket
included in the product package. Installing other
grassbasketstothemachinemaycauseamalfunc-
tionandcauseaninjury.
►Fig.10
Attaching the mulching attachment
For DLM460
1. Open the rear cover, and then remove the grass
basket.
►Fig.11: 1. Rear cover 2. Grass basket
2. Attach the mulching attachment while holding
down the lever, and then release the lever to lock the
mulching attachment.
►Fig.12: 1. Lever 2. Mulching attachment
For DLM461
1. Open the rear cover, and then remove the grass
basket.
►Fig.13: 1. Rear cover 2. Grass basket
2. Attach the mulching attachment while pulling the
lever, and then release the lever to lock the mulching
attachment.
►Fig.14: 1. Mulching attachment 2. Lever
FUNCTIONAL
DESCRIPTION
Installing or removing battery
cartridge
CAUTION: Always switch o󰀨 the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the machine and the battery
cartridge rmly when installing or removing bat-
tery cartridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipo󰀨yourhands
andresultindamagetothetoolandbatterycartridge
andapersonalinjury.
CAUTION: Make sure that you lock the battery
cover before use. Otherwise,mud,dirt,orwatermay
causedamagetotheproductorthebatterycartridge.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causinginjuryto
youorsomeonearoundyou.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.
NOTE:Thetooldoesnotworkwithonlyonebattery
cartridge.
To install the battery cartridge;
1. Pullupthelockinglever,andthenopenthebattery
cover.
►Fig.15: 1.Batterycover2. Locking lever
2. Alignthetongueonthebatterycartridgewiththe
slot on the mower then slide the cartridge until it locks in
place with a little click.
►Fig.16: 1.Batterycartridge

12 ENGLISH
3. Insertthelockkeyintheplaceshowninthegure
as far as it will go.
►Fig.17: 1.Lockkey
4. Closethebatterycoverandpushituntilitis
latched with the locking lever.
To remove the battery cartridge from the mower;
1. Pullupthebatterycoverlockingleverandopen
thebatterycover.
2. Pulloutthebatterycartridgefromthemowerwhile
sliding the button on the front of the cartridge.
3. Pulloutthelockkey.
4. Closethebatterycover.
Tool / battery protection system
Thetoolisequippedwithatool/batteryprotectionsys-
tem.Thissystemautomaticallycutso󰀨powertothe
motortoextendtoolandbatterylife.Thetoolwillauto-
maticallystopduringoperationifthetoolorbatteryis
placed under one of the following conditions:
Overload protection
Whenthebatteryisoperatedinamannerthatcauses
ittodrawanabnormallyhighcurrent,thetoolautomati-
callystopsandthemainpowerlampblinksingreen.In
thissituation,turnthetoolo󰀨andstoptheapplication
that caused the tool to become overloaded. Then turn
the tool on to restart.
Overheat protection
Whenthetoolorbatteryisoverheated,thetoolstops
automaticallyandthemainpowerlamplightsupinred.
Inthiscase,letthetoolandbatterycoolbeforeturning
the tool on again.
Overdischarge protection
Whenthebatterycapacityisnotenough,thetoolstops
automaticallyandthemainpowerlampblinksinred.In
thiscase,removethebatteryfromthetoolandcharge
thebatterycartridgesorchangethebatterycartridges
tofullychargedones.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.18: 1. Indicator lamps 2. Check button
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydi󰀨erslightly
fromtheactualcapacity.
Control panel
The control panel has the main power switch, the mode
switchingbutton,andtheindicatorofremainingbattery
capacity.
►Fig.19: 1.Batteryindicator2. Mode switching
lamp 3. Main power lamp 4. Check button
5. Mode switching button 6. Main power
switch
Main power switch
WARNING: Always turn o󰀨 the main power
switch when not in use.
To turn on the machine, press the main power switch.
Themainpowerlamplightsupingreen.Toturno󰀨the
machine, press the main power switch again.
NOTE: If the main power lamp lights up in red or
blinks in red or green, refer to the instructions for tool/
batteryprotectionsystem.
NOTE:Thismachineemploystheautopower-o󰀨
function. To avoid unintentional start up, the main
powerswitchwillautomaticallyshutdownwhenthe
switch lever is not pulled for a certain period after the
main power switch is turned on.

13 ENGLISH
Mode switching button
Youcanswitchtheoperatingmodebypressingthe
mode switching button. When the machine is turned on,
themachinestartsupinthenormalmode.Whenyou
press the mode switching button, the machine shifts to
theenergy-savingmodeandthemodeswitchinglamp
lightsupingreen.Intheenergy-savingmode,youcan
decreasethenoiseatmowing.Whenyoupressthe
mode switching button again, the machine returns to
the normal mode.
Indicating the remaining battery
capacity
Pressthecheckbuttontoindicatetheremainingbattery
capacities.Thebatteryindicatorscorrespondtoeach
battery.
Battery indicator status
Remaining battery
capacity
On O󰀨
50% - 100%
20% - 50%
0% - 20%
Switch action
WARNING: Before installing the battery car-
tridge, always check to see that the switch lever
actuates properly and returns to the original
position when released. Operating a machine with a
switchthatdoesnotactuateproperlycanleadtoloss
ofcontrolandseriouspersonalinjury.
NOTE: The mower does not start without pressing the
switch button even the switch lever is pulled.
NOTE:Mowermaynotstartduetotheoverload
whenyoutrytomowlongordensegrassatatime.
Increase the mowing height in this case.
Thismowerisequippedwiththeinterlockswitchand
handleswitch.Ifyounoticeanythingunusualwitheither
oftheseswitches,stopoperationimmediatelyand
havethemcheckedbyyournearestMakitaAuthorized
Service Center.
1. Installthebatterycartridges.Insertthelockkey
intotheinterlockswitchandthenclosethebattery
cover.
2. Press the main power switch.
3. Press the switch button and hold it.
4. Grab the upper handle and pull the switch lever.
►Fig.20: 1. Switch button 2. Upper handle 3. Switch
lever
NOTE:Ifthelockkeyisnotinserted,thepowerlamp
blinksingreenwhenyoupulltheswitchlever.
5. Release the switch button as soon as the motor
startsrunning.Themowerwillcontinuetorununtilyou
release the switch lever.
6. Release the switch lever to stop the motor.
Adjusting the mowing height
WARNING: Never put your hand or leg under
the mower body when adjusting the mowing
height.
WARNING: Always make sure that the lever
ts in the groove properly before operation.
Themowingheightcanbeadjustedintherangeof
between 20 mm and 75 mm.
Removethelockkey,andthenpullthemowingheight
adjustingleveroutwardofthemowerbodyandmoveit
toyourdesiredmowingheight.
►Fig.21: 1.Mowingheightadjustinglever
Hold the front grip with one hand, and then move the
mowingheightadjustingleverwiththeotherhand.
►Fig.22: 1.Mowingheightadjustinglever2. Front
grip
NOTE:Themowingheightguresshouldbeused
justasaguideline.Dependingontheconditionsof
thelawnortheground,theactuallawnheightmay
becomeslightlydi󰀨erentfromthesetheight.
NOTE:Tryatestmowingofgrassinalessconspicu-
ousplacetogetyourdesiredheight.
Adjusting the handle height
CAUTION: Before removing the bolts, hold
the upper handle rmly.Otherwise,thehandlemay
fallandcauseaninjury.
Thehandleheightcanbeadjustedinthreelevels.
1. Loosen the thumb nuts of the lower handle, and
then remove the bolts, washer, and thumb nuts.
►Fig.23: 1. Thumb nut 2. Washer 3. Bolt
2. Adjustthehandleheight.
3. Insert the bolts from inside, then attach washers
from outside, and then tighten the thumb nuts.

14 ENGLISH
Using mulching attachment
Themulchingattachmentallowsyoutoreturnthecut
grass to the ground without gathering the cut grass in
thegrassbasket.Whenyouoperatethemachinewith
the mulching attachment, be sure to remove the grass
basket.
NOTICE: When using the machine with the
mulching plug, make sure that the total length of
grass after cutting is 30 mm or more, and the cut
length is 15 mm or less.
►Fig.24: (1) 30 mm or more (2) 15 mm or less
Electronic function
Themachineisequippedwiththeelectronicfunctions
foreasyoperation.
• Constant speed control
Electronic speed control for obtaining constant
speed.Possibletogetnenish,becausethe
rotating speed is kept constant even under load
condition.
• Soft start
The soft-start function minimizes start-up shock,
andmakesthemachinestartsmoothly.
OPERATION
Mowing
WARNING: Before mowing, clear away sticks
and stones from mowing area. Furthermore, clear
away any weeds from mowing area in advance.
WARNING: Always wear the safety goggles or
safety glasses with side shields when operating
the mower.
CAUTION: If the cut grass or foreign object
blocks up inside of the mower body, be sure to
remove the lock key and battery cartridge and
wear gloves before removing the grass or foreign
object.
NOTICE: Use this machine for mowing lawn only.
Do not mow weeds with this machine.
►Fig.25
Firmlyholdthehandlewithbothhandswhenmowing.
Themowingspeedguidelineisapproximately1meter
per 4 seconds.
►Fig.26
The center lines of the front wheels are guidelines to
mowing width. Using the center lines as guidelines,
mowinstrips.Overlapbyonehalftoonethirdtheprevi-
ousstriptomowthelawnevenly.
►Fig.27: 1. Mowing width 2. Overlapping area
3. Center line
Change the mowing direction each time to prevent the
grassgrainpatternfromforminginjustonedirection.
►Fig.28
Periodicallycheckthegrassbasketformowedgrass.
Emptythegrassbeforeitbecomesfull.Beforeevery
periodical check, be sure to stop the mower then
removethelockkeyandthebatterycartridge.
NOTE: Using the mower with the grass basket full
prevents smooth blade rotation and places an extra
loadonthemotor,whichmaycausebreakdown.
Mowing a long-grass lawn
Donottrytocutlonggrassallatonce.Instead,mow
thelawninsteps.Leaveadayortwobetweenmowings
untilthelawnbecomesevenlyshort.
►Fig.29
NOTE: Mowing long grass to a short length all at
oncemaycausethegrasstodie.Thecutgrassmay
alsoblockupinsideofthemowerbody.
Emptying the grass basket
WARNING: To reduce a risk of accident, reg-
ularly check the grass basket for any damage or
weakened strength. Replace the grass basket if
necessary.
1. Release the switch lever.
2. Removethelockkey.
3. Open the rear cover and take out the grass basket
byholdingthehandle.
►Fig.30: 1. Rear cover 2. Handle 3. Grass basket
4. Emptythegrassbasket.
MAINTENANCE
WARNING: Always be sure that the lock
key and battery cartridge are removed from the
mower before storing or carrying the mower or
attempting to perform inspection or maintenance.
WARNING: Always remove the lock key when
the mower is not in use. Store the lock key in a
safe place out of reach of children.
WARNING: Wear gloves when performing
inspection or maintenance.
WARNING: Always wear the safety goggles or
safety glasses with side shields when performing
inspection or maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers,alwaysusingMakitareplacementparts.

15 ENGLISH
Maintenance
1. Removethelockkeyandbatterycartridges,and
thenclosethebatterycover.
2. Put the mower on its side and clean grass clip-
pings accumulated on the underside of mower deck.
3. Pour water toward the bottom of the machine to
which the blade is attached.
NOTICE: Do not wash the machine with high
pressure water.
4. Check all nuts, bolts, knobs, screws, fasteners etc.
for tightness.
5. Inspect moving parts for damage, breakage, and
wear. Damaged or missing parts should be repaired or
replaced.
6. Store the mower in a safe place out of the reach of
children.
Carrying the mower
Whencarryingthemower,holdthefrontgripandlower
handlewithtwopeopleasshowninthegure.
►Fig.31: 1. Lower handle 2. Front grip
Storing
Storemowerindoorsinacool,dryandlockedplace.
Don't store the mower and charger in locations where
thetemperaturemayreachorexceed40°C(104°F).
1. Open the rear cover and take out the grass basket
byholdingthehandle.
►Fig.32: 1. Rear cover 2. Handle 3. Grass basket
2. Loosen the thumb nuts and fold the upper handle.
►Fig.33: 1. Upper handle 2. Thumb nut
Removing or installing the mower
blade
WARNING: Always remove the lock key and
battery cartridge when removing or installing the
blade. Failure to remove the lock key and battery
cartridge may cause a serious injury.
WARNING: The blade coasts for a few sec-
onds after releasing the switch. Do not start any
operation until the blade comes to a complete
stop.
WARNING: Always wear gloves when han-
dling the blade.
Removing the mower blade
1. Put the mower on its side so that the mowing
heightadjustinglevercomestotheupperside.
2. To lock the blade, insert a lumber or similar into
the mower.
3. Turn the bolt counterclockwise with the wrench.
►Fig.34: 1. Mower blade 2. Wrench 3. Lumber
4. Remove the bolt, washer, mower blade in order.
►Fig.35: 1. Mower blade 2. Washer 3. Bolt
Installing the mower blade
To install the mower blade, take the removal procedure
in reverse.
WARNING: Install the mower blade carefully.
It has a top/bottom facing. Place the blade so that
the rotational direction arrow faces outward.
WARNING: Tighten the bolt clockwise rmly
to secure the blade.
WARNING: Make sure that the mower blade
and all the xing parts are installed correctly and
tightened securely.
WARNING: When you replace the blades,
always follow the instructions provided in this
manual.

16
TROUBLESHOOTING
Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedinthemanual,
donotattempttodismantlethetool.Instead,askMakitaAuthorizedServiceCenters,alwaysusingMakitareplace-
ment parts for repairs.
State of abnormality Probable cause (malfunction) Remedy
Mower does not start. Twobatterycartridgesarenotinstalled. Installthechargedbatterycartridges.
Batteryproblem(undervoltage) Rechargethebatterycartridge.Ifrechargingisnot
e󰀨ective,replacebatterycartridge.
Thelockkeyisnotinserted. Insertthelockkey.
Motor stops running after a little use. Battery'schargelevelislow. Rechargethebatterycartridge.Ifrechargingisnot
e󰀨ective,replacebatterycartridge.
Cutting height is too low. Increase the cutting height.
Motor does not reach maximum
RPM.
Batterycartridgeisinstalledimproperly. Installthebatterycartridgeasdescribedinthis
manual.
Batterypowerisdropping. Rechargethebatterycartridge.Ifrechargingisnot
e󰀨ective,replacebatterycartridge.
Thedrivesystemdoesnotwork
correctly.
Askyourlocalauthorizedservicecenterforrepair.
Mower blade does not rotate:
stopthemowerimmediately!
Foreignobjectsuchasabranchis
jammedneartheblade.
Removetheforeignobject.
Thedrivesystemdoesnotwork
correctly.
Askyourlocalauthorizedservicecenterforrepair.
Abnormal vibration:
stopthemowerimmediately!
Bladeisimbalanced,excessivelyor
unevenlyworn.
Replace the blade.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual.Theuseofanyother
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Mower blade
• Makitagenuinebatteryandcharger
NOTE:Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.Theymay
di󰀨erfromcountrytocountry.
ENGLISH

17 BAHASA INDONESIA
BAHASA INDONESIA (Petunjuk Asli)
SPESIFIKASI
Model: DLM460 DLM461
Lebar pemotong (diameter pisau) 460 mm
Kecepatan tanpa beban 2.500 min-1
Kecepatan maksimal 3.300 min-1
Nomor komponen pisau pemotong pengganti 199367-2
Dimensi
(P x L x T)
saat dioperasikan P: 1.319 mm hingga 1.518 mm
L: 532 mm
T: 879 mm hingga 1.138 mm
pada saat disimpan
(tanpakeranjangrumput)
P: 1.004 mm hingga 1.125 mm
L: 532 mm
T: 533 mm hingga 713 mm
Tegangan terukur D.C. 36 V
Berat bersih 25,3 - 27,6 kg 25,2 - 27,2 kg
Derajatperlindungan IPX4
• Karenakesinambunganprogrampenelitiandanpengembangankami,spesikasiyangdisebutkandisinidapat
berubah tanpa pemberitahuan.
• Spesikasidankartridbateraidapatberbedadarisatunegarakenegaralainnya.
• Beratalatmungkinberbedatergantungperangkattambahanyangdipasang,termasukkartridbaterai.
Kombinasialatterberatdanteringan,sesuaiProsedurEPTA01/2014,ditunjukkanpadatabel.
Kartrid baterai yang dapat digunakan
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860B
• Beberapakartridbateraiyangtercantumdiatasmungkintidaktersedia,tergantungwilayahtempattinggal
Anda.
PERINGATAN: Hanya gunakan kartrid baterai yang tercantum di atas. Penggunaan kartrid baterai lain
dapat menimbulkan risiko cedera dan/atau kebakaran.
Simbol
Berikutiniadalahsimbol-simbolyangdigunakanpada
peralatan ini. Pastikan Anda mengerti makna masing-
masing simbol sebelum menggunakan alat.
Berhati-hatilah dan pusatkan perhatian
Anda.
Bacapetunjukpenggunaan.
Bahaya;hati-hatiterhadapobjekyang
terlempar.
Jarak antara peralatan dan orang-orang di
sekitarharussedikitnya15m.
Jangan letakkan tangan dan kaki Anda di
dekat pisau di bawah pemotong rumput.
Pisau masih tetap berputar setelah motor
dimatikan.
Lepaskan kunci pengaman sebelum
memeriksa,menyesuaikan,
membersihkan, memperbaiki,
meninggalkandanmenyimpanmesin
pemotong rumput.
Ni-MH
Li-ion
Hanyauntuknegara-negaraUE
Jangan membuang peralatan listrik atau
paket baterai bersama-sama dengan
bahan limbah rumah tangga!
DenganmemerhatikanPetunjukEropa,
tentang Limbah Peralatan Listrik dan
Elektronik serta Baterai dan Akumulator
serta Limbah Baterai dan Akumulator dan
pelaksanaannyasesuaidenganketentuan
hukum nasional, peralatan listrik dan
bateraidanpaketbateraiyangtelahhabis
umurpakainyaharusdikumpulkansecara
terpisah dan dikembalikan ke fasilitas daur
ulangyangkompatibelsecaralingkungan.
Penggunaan
Mesin ini digunakan untuk memotong rumput.

18 BAHASA INDONESIA
PERINGATAN
KESELAMATAN
Petunjuk Keselamatan Pemotong
Rumput
PERINGATAN: Bacalah semua peringatan
keselamatan dan semua petunjuk. Kelalaian
mematuhiperingatandanpetunjukdapat
menyebabkansengatanlistrik,kebakarandan/atau
cedera serius.
Simpanlah semua peringatan
dan petunjuk untuk acuan di
masa depan.
1. Jangan masukkan kunci pengaman pada
pemotong sampai siap digunakan.
2. Awasi anak-anak untuk memastikan mereka
tidak bermain-main dengan pemotong rumput
ini.
3. Jangan biarkan pemotong rumput ini
digunakan oleh anak-anak atau orang yang
tidak terbiasa menggunakannya. Peraturan
setempat mungkin membatasi usia operator.
4. Jangan gunakan pemotong jika ada orang,
khususnya anak-anak, atau binatang
peliharaan di dekatnya.
5. Selalu ingat bahwa operator atau pengguna
bertanggung jawab atas kecelakaan atau
bahaya yang terjadi pada orang-orang lain
atau propertinya.
6. Saat mengoperasikan pemotong, selalu
kenakan alas kaki dan celana panjang yang
memadai. Jangan mengoperasikan pemotong
rumput tanpa mengenakan alas kaki, atau
hanya dengan mengenakan sandal. Hindari
memakai pakaian atau perhiasan yang
longgar atau yang memiliki gantungan atau
ikatan. Bagian-bagian tersebut mungkin
saja tersangkut pada komponen mesin yang
bergerak.
7. Selalu kenakan kacamata pelindung
untuk melindungi mata dari cedera saat
menggunakan mesin listrik. Kacamata
harus sesuai dengan ANSI Z87.1 di Amerika
Serikat, EN 166 di Eropa, atau AS/NZS 1336 di
Australia/Selandia Baru. Di Australia/Selandia
Baru, secara hukum Anda juga diwajibkan
mengenakan pelindung wajah untuk
melindungi wajah Anda.
Menjadi tanggung jawab atasan untuk
menerapkan penggunaan alat pelindung
keselamatan yang tepat bagi operator mesin
dan orang lain yang berada di area kerja saat
itu.
8. Gunakan mesin pemotong hanya di siang hari
atau dalam kondisi cahaya mencukupi.
9. Hindari penggunaan pemotong pada rumput
basah.
10. Penggunaan dan pemeliharaan mesin
bertenaga baterai
- Isi ulang baterai hanya dengan pengisi daya
yang ditentukan oleh pabrik. Pengisidaya
yangcocokuntuksuatujeniskartridbaterai
tertentudapatmenimbulkanrisikokebakaranjika
digunakanuntukkartridbateraiyanglain.
- Gunakan mesin listrik hanya dengan
kartrid baterai yang telah ditentukan secara
khusus. - Penggunaan kartrid baterai lain dapat
menimbulkan risiko cedera dan kebakaran.
- Saat tidak digunakan, jauhkan kartrid dari
benda-benda logam, misalnya penjepit kertas,
koin, kunci, paku, sekrup, atau benda-benda
logam kecil lainnya, yang mungkin memicu
arus pendek dari satu terminal ke terminal
lain. Arus pendek pada terminal baterai dapat
mengakibatkan kebakaran atau ledakan.
- Jika digunakan secara tidak benar, baterai
mungkin akan mengeluarkan cairan; hindari
kontak dengan cairan ini. Jika terjadi kontak
secara tidak sengaja, bilas dengan air. Jika
cairan mengenai mata, mintalah bantuan
medis.Cairanyangkeluardaribateraidapat
menyebabkaniritasiataulukabakar.
- Jangan buang baterai ke nyala api. Sel
baterai dapat meledak. Periksa kode setempat
untukpetunjukpembuangankhususyang
memungkinkan.
- Jangan buka atau bongkar baterai. Elektrolit
yangterlepasbersifatkorosifdandapatmelukai
mataataukulit.Zattersebutdapatberacunjika
tertelan.
- Jangan mengisi daya baterai saat hujan, atau
di lokasi yang basah.
11. Selalu pegang kuat-kuat pada bagian
pegangannya.
12. Jagalah kemantapan Anda saat berdiri di area
miring.
13. Berjalan, jangan berlari.
14. Saat mengangkat atau memegang pemotong
rumput, jangan menggenggam mata pisau
pemotong atau tepian pemotong yang terlihat.

19 BAHASA INDONESIA
15. Kondisi sik - Jangan mengoperasikan
pemotong rumput saat Anda dalam pengaruh
obat-obatan terlarang, alkohol, atau obat-
obatan lainnya.
16. Jauhkan tangan dan kaki dari mata pisau
yang berputar. Perhatian - Pisau masih akan
bergerak perlahan setelah sakelar mesin
dimatikan.
17. Gunakan hanya mata pisau asli dari pabrik
yang ditentukan dalam buku petunjuk ini.
18. Sebelum dioperasikan, periksa mata pisau
atau baut pisau dengan saksama untuk
memastikan tidak ada bagian yang retak atau
rusak. Segera ganti mata pisau atau baut pisau
yang retak atau rusak.
19. Pastikan tidak ada orang lain di sekitar
sebelum mulai memotong rumput. Hentikan
pemotong apabila ada orang yang masuk ke
area kerja.
20. Untuk menghindari cedera perseorangan atau
kerusakan pada pemotong, singkirkan benda-
benda asing seperti batu, kawat, botol, tulang,
dan tongkat besar dari area kerja sebelum
mulai memotong rumput.
21. Segera hentikan pengoperasian jika Anda
merasa ada yang tidak normal. Matikan
pemotong dan cabut kuncinya. Kemudian,
periksa pemotong.
22. Jangan pernah mencoba menyetel ketinggian
pemotongan ketika mesin sedang bekerja
apabila terdapat tur tersebut pada mesin.
23. Lepaskan tuas sakelar dan tunggu hingga
mata pisau berhenti berputar sebelum
melintasi area parkir, area pejalan kaki, jalan,
dan area-area lain yang tertutup kerikil.
Selain itu, cabut kunci pengaman jika Anda
akan meninggalkan pemotong, mengambil
atau menyingkirkan sesuatu di sekitar Anda,
atau melakukan hal-hal lain yang dapat
mengalihkan perhatian dari pekerjaan Anda.
24. Objek yang terpental dari mata pisau
pemotong dapat menyebabkan cedera berat
pada manusia. Rumput harus diperiksa
dengan cermat dan dibersihkan dari segala
objek setiap kali sebelum mulai memotong.
25. Jika pemotong membentur benda asing, ikuti
langkah-langkah berikut:
- Hentikan pemotong, lepaskan tuas sakelar
dan tunggu hingga mata pisau berhenti
sepenuhnya.
- Lepas kunci pengaman dan kartrid baterai.
- Periksa mesin secara menyeluruh untuk
memastikan apakah ada bagian yang rusak.
- Gantilah mata pisau jika rusak. Perbaiki
segala kerusakan sebelum kembali
menyalakan mesin dan melanjutkan
pengoperasian pemotong rumput.
26. Sering-seringlah memeriksa keranjang rumput
untuk memastikan tidak ada bagian yang
aus atau cacat. Untuk penyimpanan, selalu
pastikan keranjang rumput kosong. Untuk
menjamin keamanan, ganti keranjang rumput
yang aus dengan komponen pengganti dari
pabrik.
27. Sangat berhati-hatilah saat memundurkan atau
menarik pemotong ke arah Anda.
28. Hentikan pisau(-pisau) jika pemotong harus
digerakkan dengan cara dimiringkan saat
melintasi permukaan selain rumput, serta saat
Anda memindahkan pemotong ke dan dari
area kerja.
29. Jangan pernah mengoperasikan pemotong
dengan mengenakan pengaman atau
pelindung yang cacat, atau tanpa memasang
perangkat pengaman, misalnya deektor dan/
atau keranjang rumput.
30. Nyalakan pemotong perlahan sesuai instruksi,
dan jaga jarak kaki Anda dari mata pisau
(-pisau).
31. Jangan memiringkan pemotong saat
menyalakan motornya, kecuali jika pemotong
harus dimiringkan saat dinyalakan. Dalam hal
ini, jangan memiringkan pemotong secara
berlebihan, dan angkatlah hanya bagian yang
semestinya, yaitu yang berjauhan dengan
operator.
32. Jangan menyalakan pemotong saat Anda
berdiri di depan lubang pembuangan.
33. Jangan letakkan tangan atau kaki di dekat atau
di bawah bagian yang berputar. Selalu jaga
jarak dari lubang pembuangan.
34. Jangan memindahkan pemotong selama
masih dalam kondisi menyala.
35. Hentikan pemotong, dan lepaskan perangkat
penonaktifan. Pastikan seluruh bagian yang
bergerak telah benar-benar berhenti.
- saat Anda meninggalkan pemotong,
- sebelum membersihkan sumbatan atau saat
membersihkan saluran yang tersumbat
- sebelum memeriksa, membersihkan atau
menggunakan pemotong,
- setelah pemotong membentur benda
asing. Periksa apakah ada kerusakan pada
pemotong, dan lakukan perbaikan sebelum
kembali menyalakan dan mengoperasikannya.
36. Jika pemotong tiba-tiba bergetar secara tidak
biasa (segera periksa)
- periksa apakah ada kerusakan,
- ganti atau perbaiki semua komponen yang
rusak,
- periksa dan kencangkan semua komponen
yang kendur.
37. Berhati-hatilah saat menyesuaikan pengaturan
pemotong agar jari-jemari Anda tidak
tersangkut di antara mata pisau yang bergerak
dan bagian tidak bergerak pada pemotong.
38. Untuk area miring, lakukan pemotongan
melintasi permukaan bagian miringnya,
bukan naik dan turun. Perhatikan pada
saat mengubah arah di area miring. Jangan
memotong secara berlebihan di area miring
yang curam.
39. Periksa baut mata pisau secara berkala dan
sering untuk memastikan kekencangannya.
40. Kencangkan semua mur, baut, dan sekrup
pengencang untuk memastikan bahwa mesin
aman untuk digunakan.
41. Selalu biarkan pemotong mendingin sebelum
disimpan.

20 BAHASA INDONESIA
42. Saat memperbaiki mata pisau, perhatikan
bahwa walaupun sakelar mesin telah
dimatikan, mata pisau masih tetap dapat
bergerak.
43. Ganti bagian yang aus atau rusak untuk
menjamin keamanan. Gunakan hanya
komponen dan aksesoris pengganti yang asli.
44. Jangan gunakan mesin ketika ada risiko
tersambar petir.
45. Ketika Anda menggunakan mesin di
permukaan berlumpur, lereng basah, atau
tempat yang licin, perhatikan pijakan Anda
dengan saksama.
46. Hindari bekerja di lingkungan yang buruk yang
dapat mengakibatkan kelelahan berlebih pada
pengguna.
47. Jangan menggunakan mesin di cuaca yang
buruk di mana jarak penglihatan menjadi
terbatas.JikaAndatidakmengikutinya,Anda
dapatterjatuhataupengoperasiandapatsalah
akibatjarakpenglihatanyangrendah.
48. Jangan ganti baterai dalam kondisi hujan.
49. Jangan biarkan mesin terendam genangan air.
50. Jangan meninggalkan mesin tanpa
pengawasan di luar saat hujan.
51. Jangan masukkan atau lepaskan kunci
pengaman saat hujan.
52. Saat daun yang basah atau kotoran menempel
pada mulut penyedot (jendela ventilasi) akibat
hujan, bersihkan.
53. Jangan cuci mesin dengan penyemprot
bertekanan tinggi.
54. Ketika mencuci mesin, pastikan baterai dan
kunci pengaman telah dilepas dan tutup
penutup baterai, serta siramkan air ke arah
belakang mesin tempat pisau terpasang.
55. Ketika menyimpan mesin, hindari terkena
cahaya matahari dan hujan langsung, dan
simpan di tempat yang jauh dari panas atau
lembap.
56. Lakukan pemeriksaan di tempat yang terhindar
dari hujan.
57. Setelah menggunakan mesin, bersihkan
kotoran yang menempel dan keringkan mesin
sepenuhnya sebelum disimpan.Tergantung
pada musim atau tempat, terdapat risiko
gangguan fungsi akibat pembekuan.
58. Jangan biarkan terminal baterai terkena basah
seperti air, atau baterai terendam. Jangan
tinggalkan baterai saat hujan, atau mengisi
dayanya, menggunakan, atau menyimpan
baterai di tempat yang lembap atau basah.
Jika terminal basah atau cairan masuk ke dalam
baterai,mungkindapatterjadihubungsingkatdan
terdapat risiko kelebihan panas, terbakar, atau
meledak.
59. Setelah melepas baterai dari mesin atau
pengisi daya, pastikan Anda memasang
penutup ke baterai dan simpan di tempat
kering.
60. Jangan ganti baterai dengan tangan basah.
61. Jangan menggunakan mesin dalam kondisi
bersalju.
62. Jika rumput yang dipotong basah, rumput
akan cenderung menyumbat mesin. Periksa
kondisi mesin secara berkala, dan bersihkan
rumput yang menempel bila perlu.
SIMPAN PETUNJUK INI.
PERINGATAN: JANGAN biarkan kenyamanan
atau terbiasanya Anda dengan produk (karena
penggunaan berulang) mengurangi kepatuhan
yang ketat terhadap aturan keselamatan untuk
produk yang terkait.
PENYALAHGUNAAN atau kelalaian mematuhi
kaidah keselamatan yang tertera dalam petunjuk
ini dapat menyebabkan cedera badan serius.
Petunjuk keselamatan penting untuk
kartrid baterai
1. Sebelum menggunakan kartrid baterai,
bacalah semua petunjuk dan penandaan pada
(1) pengisi daya baterai, (2) baterai, dan (3)
produk yang menggunakan baterai.
2. Jangan membongkar kartrid baterai.
3. Jika waktu beroperasinya menjadi sangat
singkat, segera hentikan penggunaan. Hal
tersebut dapat menimbulkan risiko panas
berlebih, kemungkinan mengalami luka bakar
atau bahkan terjadi ledakan.
4. Jika elektrolit mengenai mata Anda, basuh
dengan air bersih dan segera cari pertolongan
medis. Hal tersebut dapat mengakibatkan
hilangnya kemampuan penglihatan Anda.
5. Jangan menghubungkan terminal kartrid
baterai:
(1) Jangan menyentuhkan terminal dengan
bahan penghantar listrik apa pun.
(2) Hindari menyimpan kartrid baterai pada
wadah yang berisi benda logam lain
seperti paku, uang logam, dsb.
(3) Jangan membiarkan baterai terkena air
atau kehujanan.
Hubungan singkat baterai dapat menyebabkan
aliran arus listrik yang besar, panas berlebih,
kemungkinan mengalami luka bakar dan
bahkan kerusakan pada baterai.
6. Jangan menyimpan mesin dan kartrid baterai
pada lokasi dengan suhu yang bisa mencapai
atau melebihi 50 °C.
7. Jangan membuang kartrid baterai di tempat
pembakaran sampah walaupun benar-benar
rusak atau tidak bisa digunakan sama sekali.
Kartrid baterai bisa meledak jika terbakar.
8. Berhati-hatilah jangan sampai baterai jatuh
atau terbentur.
9. Jangan menggunakan baterai yang rusak.