Makita DCU180 User manual

DCU180
EN Battery Powered
Wheelbarrow INSTRUCTION MANUAL 13
ID Gerobak Sorong Tenaga
Baterai PETUNJUK PENGGUNAAN 25
VI Xe Vận Chuyển Loại Tự Hành
Hoạt Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 38
TH   50

10
9 8 6
7
6
5
4
3
2
1 2
Fig.1
10
9 8 6
7
5
4
3
2
1 2
6
Fig.2
Fig.3
1
Fig.4
1
Fig.5
1
Fig.6
231
Fig.7
Fig.8
2

A
Fig.9
1
Fig.10
1
1
Fig.11
1
Fig.12
1
1
Fig.13
1
1
Fig.14
3

1
Fig.15
1
2
Fig.16
12
Fig.17
1
2
Fig.18
1
1
Fig.19
12
3
4
5
3
Fig.20
4

1
3
4
2
1
Fig.21
1
2
Fig.22
1
Fig.23
1
Fig.24
1
2
Fig.25
1
Fig.26
5

1
Fig.27
11
2
Fig.28
4
123
5
6
Fig.29
1
2
Fig.30
1
23
Fig.31
1
Fig.32
1
2
Fig.33
6

1
Fig.34
1
2
2
Fig.35
2
1
Fig.36
1
1
1
1
2
Fig.37
Fig.38
1
Fig.39
1
Fig.40
7

1
2
Fig.41
Fig.42
1
Fig.43
Fig.44
Fig.45
Fig.46
Fig.47
8

Fig.48
12
Fig.49
1
Fig.50
1
2
2
Fig.51
1
Fig.52
1
2
Fig.53
12
Fig.54
9

1
Fig.55
12
Fig.56
1
Fig.57
1
Fig.58
10

1
Fig.59
12
Fig.60
1
Fig.61
12
Fig.62
11

1
Fig.63
1
Fig.64
Fig.65
12

13 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DCU180
Dimensions
(L x W x H)
When carrier is installed During operation: 1,315 mm x 1,060 mm x 900 mm
When stored: 1,110 mm x 820 mm x 820 mm
When bucket is installed During operation: 1,310 mm x 820 mm x 900 mm
When stored: 1,110 mm x 820 mm x 820 mm
Traveling
speed
Forward 1.5 or 3.5 km/h
Reverse 1.0 km/h
Minimum turning radius 1,075 mm (Outer diameter when turning with front wheel as axis)
Maximum climbing capacity 12°
Maximum load capacity 130 kg
Brake Front wheel Disc brake with wire
Rear wheel Fixed with pedal
Tire Front wheel Tubeless tire
Rear wheel Self-sealing tire
Rated voltage D.C. 18 V
Net weight When carrier is installed 45 kg
When bucket is installed 39 - 40 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsandbatterycartridgemaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
andchargersmaycauseinjuryand/orre.
WARNING: Do not use a corded power supply such as battery adapter or portable power pack with
this machine.Thecableofsuchpowersupplymayhindertheoperationandresultinpersonalinjury.

14 ENGLISH
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Ni-MH
Li-ion
Only for EU countries
Do not dispose of electric equipment
or battery pack together with house-
hold waste material!
In observance of the European
Directives, on Waste Electric and
Electronic Equipment and Batteries
and Accumulators and Waste
Batteries and Accumulators and their
implementation in accordance with
national laws, electric equipment
and batteries and battery pack(s)
that have reached the end of their
life must be collected separately
and returned to an environmentally
compatible recycling facility.
Fully pull down the lever and check
that the carrier or bucket is locked.
Do not change the direction on steep
slopes.
Loadandunloadobjectsonat
ground.
Loadobjectsonthecarrierorbucket
evenly.
This machine cannot be used on the
public road.
Do not use for transporting persons.
Do not expose to rain.
To cancel the beep sound, release
the switch trigger and pull the brake
lever.
Do not stare into beam.
Intended use
The machine is intended for loading and carrying
objectswithbatterypoweredassistance.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
7. Power tools can produce electromagnetic
elds (EMF) that are not harmful to the user.
However, users of pacemakers and other similar
medical devices should contact the maker of their
device and/or doctor for advice before operating
this power tool.

15 ENGLISH
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the o󰀨-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.Looseclothes,jewelleryor
long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action
cancausesevereinjurywithinafractionofa
second.
9. Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and o󰀨. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
foroperationsdi󰀨erentfromthoseintendedcould
result in a hazardous situation.
8. Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
9. When using the tool, do not wear cloth work
gloves which may be entangled. The entangle-
ment of cloth work gloves in the moving parts may
resultinpersonalinjury.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
onetypeofbatterypackmaycreateariskofre
when used with another battery pack.
2. Use power tools only with specically desig-
nated battery packs. Use of any other battery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nalstogethermaycauseburnsorare.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritation or burns.

16 ENGLISH
5. Do not use a battery pack or tool that is dam-
aged or modied.Damagedormodiedbatteries
may exhibit unpredictable behaviour resulting in
re,explosionorriskofinjury.
6. Do not expose a battery pack or tool to re or
excessive temperature.Exposuretoreortem-
perature above 130 °C may cause explosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions. Charging improperly or at temperatures
outsidethespeciedrangemaydamagethe
batteryandincreasetheriskofre.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
3. Follow instruction for lubricating and chang-
ing accessories.
Battery powered wheelbarrow safety
warnings
1. While operating the machine, always wear
non-slip and protective footwear. Non-skid,
closed-toed safety boots and shoes will reduce the
riskofinjury.
2. Inspect pathway before hauling objects/mate-
rials. Familiarizing yourself with the pathway and
ensuring it is wide enough to safely navigate the
machine under load will help reduce losing control
of the machine.
3. Use extreme caution on slippery, loose and
unstable terrain. Wet and slippery surfaces, such
as wet grassy areas, snow or ice, and loose and
unstable terrain, such as sand or gravel surfaces,
may cause the machine to lose traction and may
adverselya󰀨ectsteering,brakingandstability.
4. Do not operate the machine on excessively
steep slopes. This reduces the risk of loss of
control, slipping and falling which may result in
personalinjury.Slopesgreaterthanthemaxi-
mum recommended grade and side grades may
increase the risk of instability and may adversely
a󰀨ecttheabilitytostopsafely.
5. When working on slopes, always be sure of
your footing, always work across the face
of slopes, never up or down, and exercise
extreme caution when changing direction. This
reduces the risk of loss of control, slipping and
fallingwhichmayresultinpersonalinjury.
6. Whenever possible, use level areas for stop-
ping, loading and unloading and never leave
machine unattended on a slope. The machine is
more unstable when resting on a slope than when
resting on a level surface.
7. When stopping on slopes, face the machine
uphill or downhill and block unbraked wheels.
The machine is less stable when facing across a
slope. Unbraked wheels, especially those of the
castor-type, can potentially turn and roll downhill
even while the front wheel parking brake is set.
8. When leaving the machine unattended, set
parking brake once the machine is located in a
safe stopping area. The parking brake prevents
unwanted movement of the front wheel and can
improve stability.
9. Ensure that ramps are clean, strong and
secure.Inordertoreducetheriskofinjury,all
ramps must be clear of loose debris and strong
enough to withstand the weight of anticipated
loads that will be moved over them. They must
have adequate blocking underneath and to both
sidestoeliminatedeectionsandside-to-side
movement under load. All ramps must be wide
enough to have sure footing while hauling loads
across them.
10. Ensure the hopper is down and hoppers
and dump-gates are securely latched when
not dumping the load and when storing the
machine. Unlatched hoppers or dump-gates can
unexpectedly open or shift.
11. Avoid extending ramps without toe boards
or railings over open spaces. Elevated open
spaces and open trenches invite accidental falls
andincreasethepotentialforseriousinjury.Use
toe boards or railings on ramps over open spaces
topreventdrivingthemachineo󰀨theramp.
12. Ensure all locking screws are tightly secure
before using. Locking screws on the rear wheels
and open-type carrier front and side walls must be
secure to prevent unwanted movement of these
adjustablepartsofthemachine.
13. Never operate the machine in an overloaded
condition. Make sure the machine has the proper
capacityratingfortheobjectsormaterialsthat
have to be hauled. Excessive loads will make
themachinemoredi󰀩culttomaneuverandstop,
will increase stopping time and distance, and will
increase the risk of instability.
14. Never operate your machine in an over stacked
condition. Stacking material above the tray rim or
over the sides of the tray can cause the machine
to be uncontrollably out of balance and control.
15. Use containers and tie-downs to secure loads.
Loose and/or insecure loads are more likely
to shift which can result in loss of stability and
control.
16. Always maintain a rm grip on handles. Loss of
controlcanincreasetheriskofpersonalinjury.
17. Remove safety key when not in use. The safety
key prevents unwanted, powered use of the
machine, such as by children or other untrained
or unauthorized persons. Without the key, electric
power cannot be turned “on”.
18. This machine cannot be used on public roads.
Use of the wheelbarrow on a public road is unlaw-
fulandcouldresultinlocaljurisdictionpenaltiesin
additionitcouldresultinpersonalinjury.

17 ENGLISH
19. Use a sturdy plate with anti-slip and detach-
ment prevention function when loading and/
or unloading this machine for transportation,
or moving this machine between di󰀨erent
levels. Make sure the plate inclination does not
exceed 12°, and operate the machine slowly
and carefully. Unstable and quick operation
may result in overturn and/or falling.
20. Do not disassemble, repair, or modify this
machine.
Operation
1. When operating the machine, stand behind the
machine and hold the handles rmly.
2. Do not operate the machine while riding on the
machine.
3. Do not allow others to ride on the machine.
4. When operating the machine in reverse and
walking backward, watch behind you and be
careful not to slip or trip.
5. Do not use the machine when visibility is poor
because there is a risk of striking obstacles.
6. When operating the machine on rough ground,
decrease speed and exercise caution.
7. When using the machine, avoid soft ground
to prevent overturn due to the shoulder of the
road collapsing.
8. Do not operate the machine on upward slopes
greater than 12°.
9. If you nd an abnormality, stop the machine
on at ground. Before inspecting the machine,
pull the brake lever and lock the brake, and
then turn the power o󰀨.
10. Before operating the machine, make sure that
the lock lever is fully pulled down and com-
pletely locked. If the lock is incomplete, there is
ariskofaccidentorinjuryasthecarrierorbucket
maybetiltedandtheobjectsfallwhengoing
downhill.
11. Be careful not to entangle the cords with the
load or obstacles.
Operation on slopes
1. Do not cross on slopes.
2. Be sure to decrease speed and exercise
caution.
3. Exercise caution when starting or stopping the
machine on slopes.
4. As the loads become less stable on slopes,
rmly secure the loads with ropes.
5. As the machine becomes unstable depending
on the condition of the road, keep the load to a
minimum.
6. As the view is obscured on slopes, keep the
height of the load to a minimum.
7. Never park the machine on steep slopes. Park
the machine on at ground, pull the brake
lever and lock the brake, and then turn the
power o󰀨.
8. Do not change the direction or speed mode on
steep slopes.
9. Do not release the switch trigger on upward
slopes. The machine may go in reverse and
cause an accident.
10. Make sure that the remaining battery capacity
is enough before operating on slopes. If the
remaining battery capacity is not enough,
charge the battery or replace it with a charged
one.
Loading objects
1. Do not overload objects. When loading
objects, be sure to follow the instructions and
load limits in the manual.
2. Firmly secure the objects with ropes.
3. Load the objects within the carrier or bucket.
Iftheobjectsprotrudefromthecarrierorbucket,
thereisariskofaccidentsduetotheobjects
falling or contact obstacles such as walls.
4. Be sure that loaded objects are below eye
level. If the load is too high, it is dangerous
because the view is obscured. Also, there is a risk
ofoverturningandinjurybecausetheloadislikely
to be unbalanced.
5. Load the objects on the carrier or bucket
evenly.Iftheobjectsareloadedunevenly,thereis
ariskofoverturningandinjurybecausetheloadis
likely to be unbalanced.
6. Before loading the objects or operating the
machine, make sure that the lock lever is fully
pulled down and completely locked.
7. Be sure to load heavy objects rst to keep
balance.
8. Do not extend the front and side rails on steep
slopes. Extend the side rails when lightweight
objects are loaded.
9. When extending the front and side rails, do not
extend them over the extension limit. Be sure
to extend the side rails so that the right and
left sides are the same length, and load objects
evenly.
10. Load and unload objects on at ground.
11. When lifting and tilting the carrier or bucket,
hold the handles and frame rmly, and work in
a stable posture.
Maintenance
1. Always be sure to park the machine on at
ground and lock the brake lever before stor-
age or attempting to perform inspections or
maintenance.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.

18 ENGLISH
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble or tamper the battery
cartridge.Itmayresultinare,excessiveheat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
re,excessiveheat,orexplosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tapeormasko󰀨opencontactsandpackupthe
battery in such a manner that it cannot move
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliantproductsmayresultinare,exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may result in poor performance or
breakdown of the tool or battery cartridge.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causingres,personalinjuryanddamage.Itwill
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
PARTS DESCRIPTION
Parts description (when the carrier
is installed)
►Fig.1
1Control panel 2Handle
3Switch trigger 4Battery box
5Brake lever for front
wheel
6Rear wheel
7Brake pedal for rear
wheel
8Lamp
9Front wheel 10 Carrier

19 ENGLISH
Parts description (when the bucket
is installed)
►Fig.2
1Control panel 2Handle
3Switch trigger 4Battery box
5Brake lever for front
wheel
6Rear wheel
7Brake pedal for rear
wheel
8Lamp
9Front wheel 10 Bucket
ASSEMBLY
CAUTION: Always be sure that the machine is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the machine.
Assembling main unit
1. Take out the base unit and handles from the box.
►Fig.3
NOTICE: Be sure to take out the base unit and
handles together, so that excessive force is not
applied to the cords.
2. Place the packing material under the rear side of
the base unit.
►Fig.4: 1. Packing material
3. Insert the rear wheels into the frame.
►Fig.5: 1. Rear wheel
►Fig.6: 1. Rear wheel
NOTE: The support legs can be attached instead of
the rear wheels.
4. Attach the spring washer and the washer to the
short hexagonal bolt, and then tighten them using the
wrench included in the package.
►Fig.7: 1. Short hexagonal bolt 2. Spring washer
3. Washer
►Fig.8
NOTICE: Be sure to use the short hexagonal
bolts to tighten the rear wheels.
NOTICE: Fix the rear wheels at the same position
on both sides.
5. Raise the handles, and then insert them into the
base unit.
►Fig.9
NOTICE: Do not allow the cords inside area “A”
in the gure.Longobjectsmaybeentangledwiththe
cords and cause accidents.
NOTICE: Do not apply excessive force to the
cords when raising and inserting the handles.
NOTICE: Be sure to raise the handles with both
hands.
6. Open the carrier frame toward the front.
►Fig.10: 1. Carrier frame
7. Unfold the handles, then insert the long hexagonal
bolts into the base unit, and then tighten the nuts with
the wrench included in the package.
►Fig.11: 1. Long hexagonal bolt
8. Tighten the shoulder bolts from the rear using the
wrench included in the package.
►Fig.12: 1. Shoulder bolt
9. Tighten the short hexagonal bolts from both sides
usingthewrenchincludedinthepackagetoxthe
handles.
►Fig.13: 1. Short hexagonal bolt
NOTICE: Do not tighten the short hexagonal
bolts with excessive force. Tighten them with
properforcesothatthehandlesarestablyxed.
NOTICE: Do not pinch the cords with the bolts.
10. Fix the cords with the clamps.
►Fig.14: 1. Clamp
11. Fold the carrier frame.
►Fig.15: 1. Carrier frame
12. Press the lock button while pulling the brake lever
to lock the brake.
►Fig.16: 1. Lock button 2. Brake lever
CAUTION: If the rear wheels are installed,
press the brake pedal for the rear wheel to lock
the rear wheel.
13. Hook the carrier lock, and then pull down the lock
lever to lock the carrier.
►Fig.17: 1. Carrier lock 2. Lock lever
NOTICE: Make sure that the lock lever is locked
securely.
NOTICE: Do not pinch the cords with the lock
lever.
NOTE: If you attach the support legs instead of the
rear wheels, remove the rear wheels from the frames,
and then attach the support legs to the frames.
►Fig.18: 1. Rear wheel 2. Support leg

20 ENGLISH
Assembling and installing carrier
Optional accessory
1. Take out the carrier from the box, attach the side
rails to the base frame, and then tighten the thumb nuts
toxtherails.
►Fig.19: 1. Thumb nut
2. Place the carrier on the base unit, and then insert
the hexagonal bolts and washers into the frames from
the top. Tighten the washers and spring washers and
butterynutsfromthebottomtoxthecarrier.
►Fig.20: 1. Long hexagonal bolt 2. Short hexagonal
bolt 3. Washer 4. Spring washer 5.Buttery
nut
NOTICE: Use the long bolts for the front, and the
short bolts for the rear.
Installing bucket
Optional accessory
Place the bucket on the base unit, insert the hexagonal
bolts into the frames, and then tighten the washers and
springwashersandbutterynutsfromthebottomtox
the bucket.
►Fig.21: 1. Hexagonal bolt 2. Washer 3. Spring
washer 4.Butterynut
FUNCTIONAL
DESCRIPTION
Installing or removing battery
cartridge
CAUTION: Always switch o󰀨 the machine
before installing or removing of the battery
cartridge.
CAUTION: Make sure that you lock the battery
cover before use. Otherwise, mud, dirt, or water may
cause damage to the product or the battery cartridge.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injurytoyouorsomeonearoundyou.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION: Do not use the high-temperature
battery cartridge. When the high-temperature bat-
tery cartridge is used, the machine stops automati-
cally before a short beep sound is emitted, and may
causeaninjury.
Installing the battery cartridge
1. Rotate the lock lever, and then open the cover of
the battery box.
►Fig.22: 1. Lock lever 2. Cover
2. Align the tongue on the battery cartridge with the
slot on the battery box, and then slide the cartridge until
it locks in place with a little click. If you can see the red
indicator on the upper side of the button, battery car-
tridge is not locked completely.
►Fig.23: 1. Battery cartridge
3. Insertthelockkeyintheplaceshowninthegure
as far as it will go.
►Fig.24: 1. Lock key
NOTE: If the lock key is not inserted completely, the
machine does not work.
4. Close the cover of the battery box, and then rotate
the lock lever.
►Fig.25: 1. Lock lever 2. Cover
Removing the battery cartridge
1. Rotate the lock lever, and then open the cover of
the battery box.
2. Pull out the battery cartridge from the battery box
while sliding the button on the front of the cartridge.
►Fig.26: 1. Button
3. Pull out the lock key.
4. Close the cover of the battery box, and then rotate
the lock lever.
Machine / battery protection system
The machine is equipped with a machine/battery
protectionsystem.Thissystemautomaticallycutso󰀨
power to the motor to extend machine and battery life.
The machine will automatically stop during operation
if the machine or battery cartridge is under one of the
following conditions. A short beep sound is emitted
before the machine stops automatically. The battery
indicators and LED indicators blink while the beep
sound is emitted.
Overload protection
When the machine is operated in a manner that causes
it to draw an abnormally high current, the machine auto-
matically stops without any indication. In this situation,
turnthemachineo󰀨andremovethecauseofoverload,
and then turn the machine on to restart.
Overheat protection
When the machine is overheated, the machine stops
automatically. Let the machine cool down before turning
the machine on again. The overheat protection is likely
to work under high temperature environment.
Overdischarge protection
When the battery capacity becomes low, the machine
stops automatically. If the machine does not operate
even when the switches are operated, remove the
battery cartridge and charge it.