Makita DFR540 User manual

DFR540
DFR550
DFR750
EN Cordless Auto Feed
Screwdriver INSTRUCTION MANUAL 5
UK Бездротовий шуруповерт із
автоматичним подаванням
ІНСТРУКЦІЯ З
ЕКСПЛУАТАЦІЇ 10
PL Akumulatorowa wkrętarka z
magazyniem INSTRUKCJA OBSŁUGI 16
RO
Maşină de înşurubat cu
alimentare automată cu
acumulator
MANUAL DE INSTRUCŢIUNI 22
DE Akku-Schnellbau-Magazin-
Schrauber BEDIENUNGSANLEITUNG 28
HU Akkumulátoros önetető
csavarbehajtó HASZNÁLATI KÉZIKÖNYV 34
SK Akumulátorový skrutkovač s
automatickým podávaním NÁVOD NA OBSLUHU 40
CS Akumulátorový zásobníkový
šroubovák NÁVOD K OBSLUZE 45

1
2
3
1
1
2
1
23
4
1
2
3
5mm
A
B
1
AB
1
1
2
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
Fig.7
Fig.8
2

1
2
3
1
2
3
1
1
1
1
2
1
Fig.9
Fig.10
Fig.11
Fig.12
Fig.13
Fig.14
Fig.15
Fig.16
3

15mm
12
1
1
2
1
2
1
23
1
1
2
Fig.17
Fig.18
Fig.19
Fig.20
Fig.21
Fig.22
Fig.23
4

5ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model DFR540 DFR550 DFR750
Screw strip 4 x 25 - 55 mm 4 x 45 - 75 mm
No load speed (min-1)4,000
Overall length 424 mm 464 mm
Net weight 2.0 - 3.0 kg 2.1 - 3.1 kg 2.1 - 3.2 kg
Rated voltage D.C. 14.4 V D.C. 18 V D.C. 18 V
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.
Applicable battery cartridge and charger
Batterycartridge D.C.14.4 V Model BL1415N/BL1430/BL1430B/BL1440/BL1450/BL1460B
D.C.18 V Model BL1815N/BL1820/BL1820B/BL1830/BL1830B/BL1840/
BL1840B/BL1850/BL1850B/BL1860B
Charger DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Intended use
The tool is intended for screw driving in wood, metal
and plastic.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ingtoEN62841:
Model DFR540
Sound pressure level (LpA):77dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
Model DFR550
Sound pressure level (LpA):78dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
Model DFR750
Sound pressure level (LpA):76dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
NOTE: The declared noise emission value(s) has
beenmeasuredinaccordancewithastandardtest
methodandmaybeusedforcomparingonetoolwith
another.
NOTE: The declared noise emission value(s)
mayalsobeusedinapreliminaryassessmentof
exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
Thevibrationtotalvalue(tri-axialvectorsum)deter-
minedaccordingtoEN62841:
Workmode:screwdrivingwithoutimpact
Vibrationemission(ah):2.5m/s2or less
Uncertainty(K):1.5m/s2
NOTE:Thedeclaredvibrationtotalvalue(s)hasbeen
measured in accordance with a standard test method
andmaybeusedforcomparingonetoolwithanother.
NOTE:Thedeclaredvibrationtotalvalue(s)mayalso
beusedinapreliminaryassessmentofexposure.

6ENGLISH
WARNING: The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
TheECdeclarationofconformityisincludedasAnnexA
to this instruction manual.
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm"powertool"inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.
Cordless screwdriver safety
warnings
1. Hold the power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fastenerscontactinga"live"wiremaymake
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Always be sure you have a rm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool rmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
6. Always secure workpiece in a vise or similar
hold-down device.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery char-
ger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current ow, over-
heating, possible burns and even a breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10.
The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
Forcommercialtransportse.g.bythirdparties,
forwarding agents, special requirement on pack-
agingandlabelingmustbeobserved.
Forpreparationoftheitembeingshipped,consult-
ing an expert for hazardous material is required.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tape or mask off open contacts and pack up the
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita.Installingthebatteriesto
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.

7ENGLISH
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely dis-
charged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
battery cartridge cool down before charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).
FUNCTIONAL DESCRIPTION
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforeadjust-
ing or checking function on the tool.
Installing or removing battery cartridge
►Fig.1: 1. Red indicator 2. Button 3.Batterycartridge
• Alwaysswitchoffthetoolbeforeinstallingor
removingofthebatterycartridge.
•
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
• Toinstallthebatterycartridge,alignthetongueon
thebatterycartridgewiththegrooveinthehousing
andslipitintoplace.Alwaysinsertitallthewayuntil
itlocksinplacewithalittleclick.Ifyoucanseethe
redindicatorontheuppersideofthebutton,itisnot
lockedcompletely.Installitfullyuntiltheredindicator
cannotbeseen.Ifnot,itmayaccidentallyfalloutof
thetool,causinginjurytoyouorsomeonearoundyou.
• Donotuseforcewheninstallingthebatterycar-
tridge.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.
Battery protection system (Lithium-
ion battery with star marking)
►Fig.2: 1. Star marking
Lithium-ionbatterieswithastarmarkingareequipped
withaprotectionsystem.Thissystemautomatically
cutsoffpowertothetooltoextendbatterylife.
Thetoolwillautomaticallystopduringoperationifthetooland/
orbatteryareplacedunderoneofthefollowingconditions:
• Overloaded:
The tool is operated in a manner that causes
ittodrawanabnormallyhighcurrent.
In this situation, release the trigger switch on the tool
andstoptheapplicationthatcausedthetooltobecome
overloaded. Then pull the trigger switch again to restart.
Ifthetooldoesnotstart,thebatteryisover-
heated.Inthissituation,letthebatterycool
beforepullingthetriggerswitchagain.
• Lowbatteryvoltage:
Theremainingbatterycapacityistoolow
and the tool will not operate. In this situation,
removeandrechargethebattery.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.3: 1. Indicator lamps 2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydifferslightly
fromtheactualcapacity.
Setting for desired screw length
►Fig.4: 1. Lever 2.Stopperbase3.Labelonfeeder
box4. Fenestella
There are 7 positive-lock screw length settings. To
obtainthedesiredsetting,pulloutthestopperbase
whiledepressingtheleveruntilyouseethenumber
ofthedesiredscrewlength(indicatedonthelabelon
feederbox)appeartorestinthefenestellaofstopper
base.Seethetablebelowfortherelationbetweenthe
numberindicatedonthelabelonfeederboxandthe
respective screw length.
For Models DFR540, DFR550
25
30
35
40
45
50
55
25 mm
30 mm
35 mm
40 mm
45 mm
50 mm
55 mm
Number indicated on the label Screw length

8ENGLISH
For Model DFR750
Number indicated on the label Screw length
45
50
55
45 mm
50 mm
55 mm
60
65
70
75
60 mm
65 mm
70 mm
75 mm
Adjusting the driving depth
►Fig.5: 1.Stopperbase2. Casing 3.Adjustingknob
Depressthestopperbaseasfarasitwillgo.While
keepingitinthisposition,turntheadjustingknobuntil
thebittipprojectsapprox.5mmfromthestopperbase.
Driveatrialscrew.Ifthescrewheadprojectsabovethe
surfaceoftheworkpiece,turntheadjustingknobinthe
"A"direction;ifthescrewheadiscounter-sunk,turnthe
adjustingknobinthe"B"direction.
Switch action
►Fig.6: 1. Switch trigger
CAUTION:
• Beforeinsertingthebatterycartridgeintothe
tool,alwayschecktoseethattheswitchtrigger
actuatesproperlyandreturnstothe"OFF"
position when released.
Tostartthetool,simplypulltheswitchtrigger.Release
the switch trigger to stop.
Reversing switch action
►Fig.7: 1. Reversing switch lever
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
AsideforclockwiserotationorfromtheBsideforcoun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion,theswitchtriggercannotbepulled.
CAUTION:
• Alwayscheckthedirectionofrotationbefore
operation.
• Usethereversingswitchonlyafterthetool
comes to a complete stop. Changing the direc-
tionofrotationbeforethetoolstopsmaydam-
age the tool.
• Whennotoperatingthetool,alwayssetthe
reversing switch lever to the neutral position.
ASSEMBLY
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforecarrying
outanyworkonthetool.
Installing or removing the bit
Loosenthethumbscrewswhichsecurethecasing.Pull
out the casing in the direction of the arrow.
►Fig.8: 1. Casing 2.Thumbscrew
Pressthedustcovertowardtheplanebearingandpull
outthebit.Ifthedustcovercannotbemovedasfar
astheplanebearing,tryitagainafterturningthebit
slightly.
Toinstallthebit,insertitintothesocketwhileturningit
slightly.Afterinstalling,alwaysmakesurethatthebitis
securelyheldinplacebytryingtopullitout.
►Fig.9: 1.Planebearing2. Dust cover 3. Bit
Installing screw strip
Insert the screw strip through the screw guide. Then
insertitthroughthefeederboxuntiltherstscrew
reaches the position next to the driving position.
►Fig.10: 1.Feederbox2. Screw strip 3. Screw guide
►Fig.11: 1. Driving position
Removing screw strip
Toremovethescrewstrip,justpullitoutinthedirection
ofthearrow.Ifyoudepressthereversebutton,youcan
pull out the screw strip in the reverse direction of the
arrow.
►Fig.12
►Fig.13: 1.Reversebutton
Folding screw guide
►Fig.14
Screwguideisfoldable.Foldingthescrewguideallows
spaceusedforstoragetobeminimal.
Carry hook
Thecarryhookisconvenientfortemporarilyhooking
thetool.Itcanbeinstalledoneithersideofthetool.
Whenremovingthecarryhook,widenitbypressingits
rightendsONBOTHSIDESinthedirectionsofarrow
(1) and raise it in the direction of the arrow (2).
►Fig.15: 1. Hook

9ENGLISH
OPERATION
Driving operation
►Fig.16
Switchonthetoolbypullingtheswitchtrigger.Holdthetool
squarelyandrmlyupagainstthedrivingsurface.Ascrewwill
beautomaticallycarriedtothedrivingpositionandfastened.
CAUTION:
• Alwayscheckthebitcarefullyforwearbefore
drivingoperations.Replaceawornbitorpoor
fasteningmayresult.
• Alwaysholdthetoolsquarelyagainstthedriving
surface.Holdingitatananglemaydamagethe
screwheadsandcausewearonthebit.This
mayalsoleadtopoorfastening.
• Alwayskeepthetoolrmlyagainstthedriving
surface until the driving is over. Failure to do so
maycauseinsufcientfasteningofscrews.
• Be careful not to drive a screw onto another
screwalreadyfastened.
• Do not operate the tool without screws. It will
damage the driving surface.
• Donotapplyoilorgreaseontheslidingsurface
ofthefeederbox.
Driving in corner
►Fig.17: 1. Wall 2.Stopperbase
Thistoolcanbeusedtodriveataposition15mmaway
fromthewallasshowninthegure.
CAUTION:
• Driving at a position closer than 15 mm to the
wallordrivingwiththestopperbaseincontact
withthewallmaydamagethescrewheadsand
causewearonthebit.Thismayalsoleadto
poor fastening of screws and malfunction of the
tool.
MAINTENANCE
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforeattempt-
ing to perform inspection or maintenance.
• Neverusegasoline,benzine,thinner,alcohol
or the like. Discoloration, deformation or cracks
mayresult.
Replacing carbon brushes
►Fig.18: 1. Limit mark
Replacewhentheyweardowntothelimitmark.Keep
thecarbonbrushescleanandfreetoslipintheholders.
Bothcarbonbrushesshouldbereplacedatthesame
time.Useonlyidenticalcarbonbrushes.
Loosenthethumbscrewswhichsecurethecasing.Pull
out the casing in the direction of the arrow.
►Fig.19: 1. Casing 2.Thumbscrew
Use a screwdriver to remove two screws then remove
the front cover.
►Fig.20: 1. Front cover 2. Screws
Raise the arm part of the spring and then place it in the
recessedpartofthehousingwithaslottedbitscrew-
driver of slender shaft or the like.
►Fig.21: 1. Spring 2.Arm3. Recessed part
Useplierstoremovethecarbonbrushcapsofthe
carbonbrushes.Takeouttheworncarbonbrushes,
insertthenewonesandreplacethecarbonbrushcaps
in reverse.
►Fig.22: 1.Carbonbrushcap
Makesurethatthecarbonbrushcapshavetintothe
holesinbrushholderssecurely.
►Fig.23: 1. Hole 2.Carbonbrushcap
Reinstall the front cover and tighten two screws
securely.
TomaintainproductSAFETYandRELIABILITY,repairs,
anyothermaintenanceoradjustmentshouldbeper-
formedbyMakitaAuthorizedServiceCenters,always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
• These accessories or attachments are recom-
mendedforusewithyourMakitatoolspecied
inthismanual.Theuseofanyotheraccessories
orattachmentsmightpresentariskofinjuryto
persons.Onlyuseaccessoryorattachmentfor
its stated purpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Drywallscrewstrip
• Phillipsbit
• VarioustypeofMakitagenuinebatteriesand
chargers
• Plasticcarryingcase
NOTE:
• Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.They
maydifferfromcountrytocountry.

10 УКРАЇНСЬКА
УКРАЇНСЬКА (Оригінальні вказівки)
ТЕХНІЧНІ ХАРАКТЕРИСТИКИ
Модель DFR540 DFR550 DFR750
Стрічказгвинтами 4x25-55мм 4x45-75мм
Швидкістьбезнавантаження(хв.-1)4000
Загальнадовжина 424мм 464мм
Чиставага 2,0-3,0кг 2,1-3,1кг 2,1-3,2кг
Номінальнанапруга 14,4Впост.струму 18Впост.струму 18Впост.струму
• Оскількинашапрограманауковихдослідженьірозробоктриваєбезперервно,наведенітуттехнічні
характеристикиможутьбутизміненібезпопередження.
• Урізнихкраїнахтехнічніхарактеристикиможутьбутирізними.
• Вагаможевідрізнятисязалежновіддопоміжногообладнання,наприкладкасетизакумулятором.
Найлегшітанайважчікомплекти,відповіднодостандартуEPTA(Європейськаасоціаціявиробників
електроінструменту)відсічня01/2014року,представленовтаблиці.
Застосовна касета з акумулятором і зарядний пристрій
Касетазакумулятором Модель14,4Впост.тока BL1415N/BL1430/BL1430B/BL1440/BL1450/BL1460B
Модель18Впост.тока BL1815N/BL1820/BL1820B/BL1830/BL1830B/BL1840/
BL1840B/BL1850/BL1850B/BL1860B
Заряднийпристрій DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF
• Деякікасетизакумуляторомізарядніпристрої,яківказановище,можутьбутинедоступнимизалежно
відвашогорегіонуабомісцяперебування.
ПОПЕРЕДЖЕННЯ: Використовуйте лише касети з акумулятором і зарядні пристрої, перелічені
вище.Використаннябудь-якихіншихкасетзакумуляторомізаряднихпристроївможепризвестидотравму-
ванняй/абопожежі.
Призначення
Інструментпризначенодляукручуваннягвинтіву
деревину,пластмасутаметал.
Шум
РівеньшумузашкалоюАутиповомувиконанні,
визначенийвідповіднодоEN62841:
Модель DFR540
Рівеньзвуковоготиску(LpA):77дБ(A)
Похибка(K):3дБ(A)
Рівеньшумупідчасроботиможеперевищувати80дБ(A).
Модель DFR550
Рівеньзвуковоготиску(LpA):78дБ(A)
Похибка(K):3дБ(A)
Рівеньшумупідчасроботиможеперевищувати80дБ(A).
Модель DFR750
Рівеньзвуковоготиску(LpA):76дБ(A)
Похибка(K):3дБ(A)
Рівеньшумупідчасроботиможеперевищувати80дБ(A).
ПРИМІТКА:Заявленезначенняшумубуловимі-
ряновідповіднодостандартнихметодівтесту-
ванняйможевикористовуватисядляпорівняння
одногоінструментазіншим.
ПРИМІТКА:Заявленезначенняшумуможетакож
використовуватисядляпопередньогооцінювання
впливу.
ПОПЕРЕДЖЕННЯ: Користуйтеся засобами
захисту органів слуху.
ПОПЕРЕДЖЕННЯ: Залежно від умов
використання рівень шуму під час фактичної
роботи електроінструмента може відрізня-
тися від заявленого значення вібрації; осо-
бливо сильно на це впливає тип деталі, що
оброблюється.
ПОПЕРЕДЖЕННЯ: Забезпечте належні
запобіжні заходи для захисту оператора,
що відповідатимуть умовам використання
інструмента (слід брати до уваги всі складові
робочого циклу, як-от час, коли інструмент
вимкнено та коли він починає працювати на
холостому ході під час запуску).
Вібрація
Загальнавеличинавібрації(суматрьохвекторів)
визначеназгіднозEN62841:
Режимроботи:загвинчуваннябезударноїдії.
Вібрація(ah):2,5м/с2абоменше
Похибка(K):1,5м/с2
ПРИМІТКА:Заявленезагальнезначеннявібрації
буловиміряновідповіднодостандартнихметодів
тестуванняйможевикористовуватисядляпорів-
нянняодногоінструментазіншим.
ПРИМІТКА:Заявленезагальнезначеннявібрації
можетакожвикористовуватисядляпопереднього
оцінюваннявпливу.