Makita DLS713NZ User manual

1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
IMPORTANT: Read Before Using.
Cordless Slide Compound Miter Saw
DLS713
011234
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Makita DLS713
DLS713NZ o cerca il tuo prodotto tra le migliori offerte di Elettroutensili

2
ENGLISH (Original instructions)
SPECIFICATIONS
Model DLS713
Blade diameter 190 mm
Hole (arbor) diameter 20 mm
Max. Miter angle Left 47° , Right 57°
Max. Bevel angle Left 45°, Right 5°
Max. Cutting capacities (H x W) with blade 190 mm in diameter.
Bevel angle
Miter angle 45° (left) 0° 5° (right)
25 mm x 300 mm 52 mm x 300 mm 40 mm x 300 mm
0° -----
* 60 mm x 265 mm (Note 1) -----
25 mm x 212 mm 52 mm x 212 mm -----
45° (left and right) -----
* 60 mm x 185 mm (Note 2) -----
----- 52 mm x 163 mm -----
57° (right) -----
* 60 mm x 145 mm (Note 3) -----
No load speed (min-1) 2,200
Dimensions (L x W x H) 655 mm x 430 mm x 454 mm
Net weight 12.7 kg
Rated voltage D.C.18 V
(Note)
* mark indicates that a wood facing with the following thickness is used.
1: When using a wood facing 20 mm thickness
2: When using a wood facing 15 mm thickness
3: When using a wood facing 10 mm thickness
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END014-3
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･Read instruction manual.
･To avoid injury from flying debris, keep
holding the saw head down, after
making cuts, until the blade has come to
a complete stop.
･When performing slide cut, first pull
carriage fully and press down handle,
then push carriage toward the guide
fence.
･Do not place hand or fingers close to the
blade.
･Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
ENE076-1
Intended use
The tool is intended for accurate straight and miter
cutting in wood.
Cd
Ni-MH
Li-ion

3
GEA006-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves away
from moving parts.
Loose clothes, jewellery or long
hair can be caught in moving parts.
16. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
Use of dust collection
can reduce dust-related hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.

4
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may
cause irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
29. Follow instruction for lubricating and
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
ENB118-4
CORDLESS MITER SAW SAFETY
WARNINGS
1. Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
2. Check the saw blade carefully for cracks or
deformation before operation.
Replace damaged blades immediately.
3. Replace the kerf board when worn.
4. Use only saw blades specified by the
manufacturer which conform to EN847-1.
5. Do not use saw blades manufactured from
high speed steel.
6. Wear eye protection.
7. Wear hearing protection to reduce the risk of
hearing loss.
8. Wear gloves for handling saw blade (saw
blades shall be carried in a holder wherever
practicable) and rough material.
9. Connect miter saws to a dust collecting device
when sawing.
10. Select saw blades in relation to the material to
be cut.
11. Do not use the saw to cut other than wood.
12.
Always secure all moving portions before carrying
the tool. When lifting or carrying the tool, do not
use the guard as a carrying handle.
13. Do not operate saw without guards in place. Check
blade guard for proper closing before each use. Do
not operate saw if blade guard does not move freely
and close instantly. Never clamp or tie the blade
guard into the open position.
14. Keep the floor area free of loose material e.g.
chips and cut-offs.
15. Use only saw blades that are marked with a
maximum speed equal to or higher than the no
load speed marked on the tool.
16. When the tool is fitted with a laser or LED, do
not replace the laser or LED with a different
type. Ask an authorized service center for repair.
17. Never remove any cut-offs or other parts of the
workpiece from the cutting area whilst the tool
is running with an unguarded saw blade.
18.
Do not perform any operation freehand. The
workpiece must be secured firmly against the turn base
and guide fence with the vise during all operations.
Never use your hand to secure the workpiece.
19. Ensure that the tool is stable before each cut.
20. Fix the tool to a work bench, if needed.
21. Support long workpieces with appropriate
additional supports.
22. Never cut so small workpiece which cannot be
securely held by the vise. Improperly held
workpiece may cause kickback and serious
personal injury.
23. Never reach around saw blade.
24. Turn off tool and wait for saw blade to stop
before moving workpiece or changing
settings.
25. Unplug tool before changing blade or
servicing.
26. Stopper pin which locks the cutter head down
is for carrying and storage purposes only and
not for any cutting operations.
27. Do not use the tool in the presence of
flammable liquids or gases. The electrical
operation of the tool could create an explosion and
fire when exposed to flammable liquids or gases.
28. Use only flanges specified for this tool.

5
29.
Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt. Damage to
these parts could result in blade breakage.
30. Make sure that the turn base is properly
secured so it will not move during operation.
31.
For your safety, remove the chips, small pieces, etc.
from the table top before operation.
32. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
33. Make sure the shaft lock is released before the
switch is turned on.
34. Be sure that the blade does not contact the
turn base in the lowest position.
35.
Hold the handle firmly. Be aware that the saw moves
up or down slightly during start-up and stopping.
36. Make sure the blade is not contacting the
workpiece before the switch is turned on.
37. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
38. Wait until the blade attains full speed before
cutting.
39. Stop operation immediately if you notice
anything abnormal.
40.
Do not attempt to lock the trigger in the on position.
41. Be alert at all times, especially during
repetitive, monotonous operations. Do not be
lulled into a false sense of security. Blades are
extremely unforgiving.
42. Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive wheels may cause an injury.
43. Take care when slotting.
44. Some dust created from operation contains
chemicals known to cause cancer, birth
defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based-painted material and,
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area and
work with approved safety equipment, such as
those dust masks that are specially designed
to filter out microscopic particles.
45. To reduce the emitted noise, always be sure
that the blade is sharp and clean.
46. The operator is adequately trained in the use,
adjustment and operation of the machine.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
ENC007-7
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ﾟC (122 ﾟF).
7.
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before
completely discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.

6
3.
Charge the battery cartridge with room
temperature at 10
ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F). Let a
hot battery cartridge cool down before charging it.
4. Charge the battery cartridge once in every six
months if you do not use it for a long period of
time.
INSTALLATION
Bench mounting
1
011300
When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. Release the stopper
pin by simultaneously applying a slight downward
pressure on the handle and pulling the stopper pin.
WARNING:
• Ensure that the tool will not move on the
supporting surface. Movement of the miter saw
on the supporting surface while cutting may result
in loss of control and serious personal injury.
1
011236
This tool should be bolted with two bolts to a level and
stable surface using the bolt holes provided in the tool's
base. This will help prevent tipping and possible injury.
1
011237
Turn the adjusting bolt clockwise or counterclockwise so
that it comes into a contact with the floor surface to keep
the tool stable.
FUNCTIONAL DESCRIPTION
WARNING:
• Always be sure that the tool is switched off and
the battery cartridge is removed before
adjusting or checking the functions on the tool.
Failure to switch off and remove the battery
cartridge may result in serious personal injury from
accidental start-up.
Installing or removing battery cartridge
1
2
3
011235
• Always switch off the tool before insertion or
removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from
the tool while sliding the button on the front of the
cartridge.
• To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can see
the red part on the upper side of the button, it is not
locked completely. Insert it fully until the red part
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
• Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Battery protection system
(Lithium-ion battery with star marking)
1
012128
Lithium-ion batteries with a star marking are equipped
with a protection system. This system automatically cuts
off power to the tool to extend battery life.
1. Star marking
1. Red part
2. Button
3. Battery cartridge
1. Adjusting bolt
1. Bolt
1. Stopper pin

7
The tool will automatically stop during operation if the tool
and/or battery are placed under one of the following
conditions:
• Overloaded:
The tool is operated in a manner that causes
it to draw an abnormally high current.
In this situation, release the trigger switch on
the tool and stop the application that caused
the tool to become overloaded. Then pull the
trigger switch again to restart.
If the tool does not start, the battery is
overheated. In this situation, let the battery
cool before pulling the trigger switch again.
• Low battery voltage:
The remaining battery capacity is too low and
the tool will not operate. In this situation,
remove and recharge the battery.
Blade guard
For all countries other than European countries
1
011238
When lowering the handle, the blade guard rises
automatically. The guard is spring loaded so it returns to
its original position when the cut is completed and the
handle is raised.
WARNING:
• Never defeat or remove the blade guard or the
spring which attaches to the guard. An exposed
blade as a result of defeated guarding may result in
serious personal injury during operation.
In the interest of your personal safety, always maintain
the blade guard in good condition. Any irregular
operation of the blade guard should be corrected
immediately. Check to assure spring loaded return action
of guard.
WARNING:
• Never use the tool if the blade guard or spring
are damaged, faulty or removed. Operation of
the tool with a damaged, faulty or removed guard
may result in serious personal injury.
For European countries
1
2
011267
When lowering the handle, the blade guard A rises
automatically. The blade guard B rises as it contacts a
workpiece. The guards are spring loaded so it returns to
its original position when the cut is completed and the
handle is raised.
WARNING:
• Never defeat or remove the blade guard or the
spring which attaches to the guard. An exposed
blade as a result of defeated guarding may result in
serious personal injury during operation.
In the interest of your personal safety, always maintain
each blade guard in good condition. Any irregular
operation of the blade guards should be corrected
immediately. Check to assure spring loaded return action
of guards.
WARNING:
• Never use the tool if the blade guard or spring
are damaged, faulty or removed. Operation of
the tool with a damaged, faulty or removed guard
may result in serious personal injury.
If the see-through blade guard becomes dirty, or sawdust
adheres to it in such a way that the blade and/or workpiece is
no longer easily visible, remove the battery cartridge and clean
the guard carefully with a damp cloth. Do not use solvents or
any petroleum-based cleaners on the plastic guard because
this may cause damage to the guard.
If the blade guard becomes dirty and needs to be cleaned for
proper operation follow the steps below:
With the tool switched off and the battery cartridge removed,
use the supplied hex wrench to loosen the hex socket bolt
holding the center cover. Loosen the hex socket bolt by turning
it counterclockwise and raise the blade guard and center cover.
1
011239
1. Blade guard
1. Blade guard A
2. Blade guard B
1. Blade guard

8
With the blade guard so positioned, cleaning can be
more completely and efficiently accomplished. When
cleaning is complete reverse procedure above and
secure bolt. Do not remove spring holding blade guard. If
guard becomes damaged through age or UV light
exposure, contact a Makita service center for a new
guard. DO NOT DEFEAT OR REMOVE GUARD.
Positioning kerf board
1
2
011240
12
3
45
001800
This tool is provided with the kerf boards in the turn base to
minimize tearing on the exit side of a cut. The kerf boards are
factory adjusted so that the saw blade does not contact the
kerf boards. Before use, adjust the kerf boards as follows:
First, remove the battery cartridge. Loosen all the screws
(2 each on left and right) securing the kerf boards.
Re-tighten them only to the extent that the kerf boards
can still be easily moved by hand. Lower the handle fully
and push in the stopper pin to lock the handle in the
lowered position. Loosen two clamp screws which
secure the slide poles. Pull the carriage toward you fully.
Adjust the kerf boards so that the kerf boards just contact
the sides of the blade teeth. Tighten the front screws (do
not tighten firmly). Push the carriage toward the guide
fence fully and adjust the kerf boards so that the kerf
boards just contact the sides of blade teeth. Tighten the
rear screws (do not tighten firmly).
After adjusting the kerf boards, release the stopper pin
and raise the handle. Then tighten all the screws
securely.
NOTICE:
• After setting the bevel angle ensure that the
kerf boards are adjusted properly. Correct
adjustment of the kerf boards will help provide
proper support of the workpiece minimizing
workpiece tear out.
Maintaining maximum cutting capacity
1
2
3
011265
2
3
1
005516
This tool is factory adjusted to provide the maximum
cutting capacity for a 190 mm saw blade.
Remove the battery cartridge before any adjustment is
attempted. When installing a new blade, always check
the lower limit position of the blade and if necessary,
adjust it as follows:
First, remove the battery cartridge. Push the carriage
toward the guide fence fully and lower the handle
completely. Use the hex wrench to turn the adjusting bolt
until the periphery of the blade extends slightly below the
top surface of the turn base at the point where the front
face of the guide fence meets the top surface of the turn
base.
With the battery cartridge removed, rotate the blade by
hand while holding the handle all the way down to be
sure that the blade does not contact any part of the lower
base. Re-adjust slightly, if necessary.
WARNING:
• After installing a new blade and with the battery
cartridge removed, always be sure that the
blade does not contact any part of the lower
base when the handle is lowered completely. If
a blade makes contact with the base it may cause
kickback and result in serious personal injury.
1. Top surface of
turn table
2. Periphery of
blade
3. Guide fence
1. Adjusting bolt
2. Guide fence
3. Turn base
1. Saw blade
2. Blade teeth
3. Kerf board
4. Left bevel cut
5. Straight cut
1. Thumb screw
2. Kerf board

9
Stopper arm
1
2
011241
The lower limit position of the blade can be easily
adjusted with the stopper arm. To adjust it, move the
stopper arm in the direction of the arrow as shown in the
figure. Adjust the adjusting screw so that the blade stops
at the desired position when lowering the handle fully.
Adjusting the miter angle
1
2
34
5
011242
Loosen the grip by turning counterclockwise. Turn the
turn base while pressing down the lock lever. When you
have moved the grip to the position where the pointer
points to the desired angle on the miter scale, securely
tighten the grip clockwise.
CAUTION:
• After changing the miter angle, always secure the
turn base by tightening the grip firmly.
NOTICE:
• When turning the turn base, be sure to raise the
handle fully.
Adjusting the bevel angle
1
2
003930
1
2
3
011301
To adjust the bevel angle, loosen the lever at the rear of
the tool counterclockwise.
Push the handle to the left to tilt the saw blade until the
pointer points to the desired angle on the bevel scale.
Then tighten the lever clockwise firmly to secure the arm.
To tilt the blade to the right, push the release button at the
rear of the tool while tilting the blade slightly to the left
after loosening the lever. With the release button
depressed, tilt the saw blade to the right.
CAUTION:
• After changing the bevel angle, always secure the
arm by tightening the lever clockwise.
NOTICE:
• When tilting the saw blade be sure the handle is
fully raised.
• When changing bevel angles, be sure to position
the kerf boards appropriately as explained in the
"Positioning kerf boards" section.
Adjusting the lever position
12
003932
The lever can be repositioned at every angle 30° when
the lever does not provide full tightening.
Loosen and remove the screw that secures the lever at
the rear of the tool. Remove the lever and install it again
so that it is slightly above the level. Secure the lever with
the screw firmly.
1. Lever
2. Screw
1. Pointer
2. Bevel scale
3. Arm
1. Lever
2. Release button
1. Turn base
2. Pointer
3. Miter scale
4. Lock lever
5. Grip
1. Adjusting screw
2. Stopper arm

10
Switch action
For European countries
1
2
34
011266
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push the lever up, press in the lock-off button and then
pull the switch trigger. Release the switch trigger to stop.
WARNING:
• Before installing the battery cartridge on the
tool, always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released. Do not pull the switch
trigger hard without pressing in the lock-off
button. This can cause switch breakage.
Operating a tool with a switch that does not actuate
properly can lead to loss of control and serious
personal injury.
A hole is provided in the switch trigger for insertion of a
padlock to lock the tool off.
For all countries other than European countries
1
2
3
011243
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
WARNING:
• Before installing the battery cartridge on the
tool, always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released. Do not pull the switch
trigger hard without pressing in the lock-off
button. This can cause switch breakage.
Operating a tool with a switch that does not actuate
properly can lead to loss of control and serious
personal injury.
A hole is provided in the switch trigger for insertion of a
padlock to lock the tool off.
WARNING:
• Do not use a lock with a shank or cable any
smaller than 6.35 mm (1/4") in diameter. A
smaller shank or cable may not properly lock the
tool in the off position and unintentional operation
may occur resulting in serious personal injury.
• NEVER use tool without a fully operative
switch trigger. Any tool with an inoperative switch
is HIGHLY DANGEROUS and must be repaired
before further usage or serious personal injury may
occur.
• For your safety, this tool is equipped with a lock-off
button which prevents the tool from unintended
starting. NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the
lock-off button. A switch in need of repair may result
in unintentional operation and serious personal
injury. Return tool to a Makita service center for
proper repairs BEFORE further usage.
• NEVER defeat the lock-off button by taping down or
some other means. A switch with a defeated
lock-off button may result in unintentional operation
and serious personal injury.
ASSEMBLY
WARNING:
• Always be sure that the tool is switched off and
the battery cartridge is removed before
working on the tool. Failure to switch off and
remove the battery cartridge may result in serious
personal injury.
Hex wrench storage
12
012595
The hex wrench is stored as shown in the figure. When
the hex wrench is needed it can be pulled out of the
wrench holder. After using the hex wrench it can be
stored by returning it to the wrench holder.
1. Wrench holder
2. Hex wrench
1. Lock-off button
2. Switch trigger
3.
Hole for padlock
1. Lever
2. Switch trigger
3. Lock-off button
4. Hole for padlock

11
Installing or removing saw blade
1
011300
WARNING:
• Always be sure that the tool is switched off and
the battery cartridge is removed before
installing or removing the blade. Accidental start
up of the tool may result in serious personal injury.
CAUTION:
• Use only the Makita hex wrench provided to install
or remove the blade. Failure to do so may result in
overtightening or insufficient tightening of the hex
socket bolt. This could cause an injury.
Lock the handle in the raised position by pushing in the
stopper pin.
1
2
3
4
012586
To remove the blade, use the hex wrench to loosen the
hex socket bolt holding the center cover by turning it
counterclockwise. Raise the blade guard and center
cover.
1
2
3
4
5
012587
Press the shaft lock to lock the spindle and use the hex
wrench to loosen the hex socket bolt clockwise. Then
remove the hex socket bolt, outer flange and blade.
NOTE:
• If the inner flange is removed, install it on the
spindle with its blade mounting part facing the blade.
If the flange is installed incorrectly the flange will
rub against the machine.
123
45
6
015779
For tool with the inner flange for other than
20 mm hole-diameter saw blade
(Country specific)
The inner flange has a certain diameter of a blade
mounting part on one side of it and a different diameter of
blade mounting part on the other side. Choose a correct
side on which blade mounting part fits into the saw blade
hole perfectly.
123
45
6
015663
CAUTION:
• Make sure that the blade mounting part "a" on the
inner flange that is positioned outside fits into the
saw blade hole "a" perfectly. Mounting the blade on
the wrong side can result in the dangerous
vibration.
1234
011244
T o install the blade, mount it carefully onto the spindle,
making sure that the direction of the arrow on the surface
of the blade matches the direction of the arrow on the
blade case. Install the outer flange and hex socket bolt,
and then use the hex wrench to tighten the hex socket
bolt (left-handed) securely counterclockwise while
pressing the shaft lock.
1. Blade case
2. Arrow
3. Arrow
4. Saw blade
1. Outer flange
2. Saw blade
3. Inner flange
4. Hex socket bolt
(left-handed)
5. Spindle
6. Blade mounting
part
1. Outer flange
2. Saw blade
3. Inner flange
4. Hex socket bolt
(left-handed)
5. Spindle
6. Blade mounting
part
1. Shaft lock
2. Arrow
3. Blade case
4. Hex wrench
5. Hex socket bolt
1. Center cover
2. Hex socket bolt
3. Hex wrench
4. Safety cover
1. Stopper pin

12
Return the blade guard and center cover to its original
position. Then tighten the hex socket bolt clockwise to
secure the center cover. Release the handle from the
raised position by pulling the stopper pin. Lower the
handle to make sure that the blade guard moves properly.
Make sure the shaft lock has released spindle before
making cut.
Dust bag (accessory)
12
3
011304
To attach the fastener, align the top end of the fastener
with the triangular mark on the dust bag.
The use of the dust bag makes cutting operations
cleaner and dust collection easier. To attach the dust bag,
fit it onto the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove
particles adhering to the insides which might hamper
further collection.
NOTE:
If you connect a vacuum cleaner to your saw, cleaner
operations can be performed.
Securing workpiece
WARNING:
• It is extremely important to always secure the
workpiece correctly with the proper type of vise.
Failure to do so may result in serious personal injury
and cause damage to the tool and/or the workpiece.
• After a cutting operation do not raise the blade
until it has come to a complete stop. The raising
of a coasting blade may result in serious personal
injury and damage to the workpiece.
• When cutting a workpiece that is longer than
the support base of the saw, the material
should be supported the entire length beyond
the support base and at the same height to
keep the material level. Proper workpiece support
will help avoid blade pinch and possible kickback
which may result in serious personal injury. Do not
rely solely on the vertical vise and/or horizontal vise
to secure the workpiece. Thin material tends to sag.
Support workpiece over its entire length to avoid
blade pinch and possible KICKBACK.
12
001549
Vertical vise
2
7
4
5
3
1
6
002255
The vertical vise can be installed in two positions on
either the left or right side of the guide fence or the holder
assembly (optional accessory). Insert the vise rod into
the hole in the guide fence or the holder assembly and
tighten the screw to secure the vise rod.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the screw. If the screw to secure the vise arm
contacts the guide fence, install the screw on the
opposite side of vise arm. Make sure that no part of the
tool contacts the vise when lowering the handle fully and
pulling or pushing the carriage all the way. If some part
contacts the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
WARNING:
• The workpiece must be secured firmly against
the turn base and guide fence with the vise
during all operations. If the workpiece is not
properly secured against the fence the material
may move during the cutting operation causing
possible damage to the blade, causing the material
to be thrown and loss of control resulting in serious
personal injury.
1. Vise arm
2. Vise rod
3. Guide fence
4. Holder
5. Holder
assembly
6. Vise knob
7. Screw
1. Support
2. Turn base
1. Dust bag
2. Dust nozzle
3. Fastener

13
Horizontal vise (optional accessory)
1
2
3
4
011305
The horizontal vise can be installed on the left side of the
base. By turning the vise knob counterclockwise, the
screw is released and the vise shaft can be moved
rapidly in and out. By turning the vise knob clockwise, the
screw remains secured. To grip the workpiece, turn the
vise knob gently clockwise until the projection reaches its
topmost position, then fasten securely. If the vise knob is
forced in or pulled out while being turned clockwise, the
projection may stop at an angle. In this case, turn the vise
knob back counterclockwise until the screw is released,
before turning again gently clockwise.
The maximum width of the workpiece which can be
secured by the horizontal vise is 120 mm.
WARNING:
• Grip the workpiece only when the projection is
at the topmost position. Failure to do so may
result in insufficient securing of the workpiece. This
could cause the workpiece to be thrown, cause
damage to the blade or cause the loss of control,
which can result in PERSONAL INJURY.
Holders and holder assembly
(optional accessories)
12
002247
The holders and the holder assembly can be installed on
either side as a convenient means of supporting
workpieces horizontally. Install them as shown in the
figure. Then tighten the screws firmly to secure the
holders and the holder assembly.
When cutting long workpieces, use the holder-rod
assembly (optional accessory). It consists of two holder
assemblies and two rods 12.
2
1
002246
WARNING:
• Always support a long workpiece so it is level
with the top surface of the turn base for an
accurate cut and to prevent dangerous loss of
tool control. Proper workpiece support will help
avoid blade pinch and possible kickback which may
result in serious personal injury.
OPERATION
NOTICE:
• Before use, be sure to release the handle from the
lowered position by pulling the stopper pin.
• Do not apply excessive pressure on the handle when
cutting. Too much force may result in overload of the motor
and/or decreased cutting efficiency. Push down handle
with only as much force as is necessary for smooth cutting
and without significant decrease in blade speed.
• Gently press down the handle to perform the cut. If the
handle is pressed down with force or if lateral force is
applied, the blade will vibrate and leave a mark (saw
mark) in the workpiece and the precision of the cut will be
impaired.
• During a slide cut, gently push the carriage toward the
guide fence without stopping. If the carriage movement is
stopped during the cut, a mark will be left in the
workpiece and the precision of the cut will be impaired.
WARNING:
• Make sure the blade is not contacting the
workpiece, etc. before the switch is turned on.
Turning the tool on with the blade in contact with the
workpiece may result in kickback and serious
personal injury.
1. Press cutting (cutting small workpieces)
1
011248
1. Clamp screw
1. Holder
assembly
2. Rod 12
1. Holder
2. Holder
assembly
1. Vise knob
2. Projection
3. Vise shaft
4. Base

14
Workpieces up to 52 mm high and 97 mm wide can
be cut in the following manner.
Push the carriage toward the guide fence fully and
tighten two clamp screws which secure the slide
poles clockwise to secure the carriage. Secure the
workpiece with the proper type of vise. Switch on
the tool without the blade making any contact and
wait until the blade attains full speed before
lowering. Then gently lower the handle to the fully
lowered position to cut the workpiece. When the cut
is completed, switch off the tool and WAIT UNTIL
THE BLADE HAS COME TO A COMPLETE STOP
before returning the blade to its fully elevated
position.
WARNING:
• Firmly tighten two clamping screws which
secure the slide poles clockwise so that the
carriage will not move during operation.
Insufficient tightening of the locking screw may
cause possible kickback which may result in
serious personal injury.
2. Slide (push) cutting (cutting wide workpieces)
011245
Loosen two clamp screws which secure the slide poles
counterclockwise so that the carriage can slide freely.
Secure the workpiece with the proper type of vise. Pull
the carriage toward you fully. Switch on the tool without
the blade making any contact and wait until the blade
attains full speed. Press the handle down and PUSH
THE CARRIAGE TOWARD THE GUIDE FENCE AND
THROUGH THE WORKPIECE. When the cut is
completed, switch off the tool and WAIT UNTIL THE
BLADE HAS COME TO A COMPLETE STOP before
returning the blade to its fully elevated position.
WARNING:
• Whenever performing a slide cut, first pull the
carriage full towards you and press the handle
all the way down, then push the carriage
toward the guide fence. Never start the cut with
the carriage not pulled fully toward you. If you
perform the slide cut without the carriage pulled
fully toward you unexpected kickback may occur
and serious personal injury may result.
• Never attempt to perform a slide cut by pulling the
carriage towards you.
Pulling the carriage towards you
while cutting may cause unexpected kickback resulting in
possible serious personal injury.
• Never perform the slide cut with the handle locked
in the lowered position.
• Never loosen the knob which secures the carriage
while the blade is rotating.
A loose carriage while
cutting may cause unexpected kickback resulting in
possible in serious personal injury.
3. Miter cutting
Refer to the previously covered "Adjusting the miter
angle".
4. Bevel cut
011246
Loosen the lever and tilt the saw blade to set the
bevel angle (Refer to the previously covered
"Adjusting the bevel angle"). Be sure to retighten
the lever firmly to secure the selected bevel angle
safely. Secure the workpiece with a vise. Make sure
the carriage is pulled all the way back toward the
operator. Switch on the tool without the blade
making any contact and wait until the blade attains
full speed. Then gently lower the handle to the fully
lowered position while applying pressure in parallel
with the blade and PUSH THE CARRIAGE
TOWARD THE GUIDE FENCE TO CUT THE
WORKPIECE. When the cut is completed, switch
off the tool and WAIT UNTIL THE BLADE HAS
COME TO A COMPLETE STOP before returning
the blade to its fully elevated position.
WARNING:
• After setting the blade for a bevel cut, before
operating the tool ensure that the carriage and
blade will have free travel throughout the entire
range of the intended cut. Interruption of the
carriage or blade travel during the cutting operation
may result in kickback and serious personal injury.
• While making a bevel cut keep hands out of the path
of the blade.
The angle of the blade may confuse the
operator as to the actual blade path while cutting and
contact with the blade will result in serious personal injury.
• The blade should not be raised until it has come to a
complete stop.
During a bevel cut the piece cut off may

15
come to rest against the blade. If the blade is raised
while it is rotating the cut-off piece maybe ejected by the
blade causing the material to fragment which may result
in serious personal injury.
NOTICE:
• When pressing down the handle, apply pressure in
parallel with the blade. If a force is applied
perpendicularly to the turn base or if the pressure
direction is changed during a cut, the precision of
the cut will be impaired.
5. Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter
angle is being cut on a workpiece. Compound
cutting can be performed at the angle shown in the
table.
Miter angle
Left and Right 45
Right 50
Right 55
Right 57
Bevel angle
Left 0 - 45
Left 0 - 40
Left 0 - 30
Left 0 - 25
006393
When performing compound cutting, refer to "Press
cutting", "Slide cutting", "Miter cutting" and "Bevel
cut" explanations.
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a
compound miter saw with the moldings laid flat on
the turn base.
123
001555
There are two common types of crown moldings
and one type of cove moldings; 52/38° wall angle
crown molding, 45° wall angle crown molding and
45° wall angle cove molding. See illustrations.
(1) (2) (3) (4)
1 2
Fig.A
001556
2
(1)
(2)
(1)
(2)
(2)
(1)
(2)
(1)
(1)
(2)
(3)
(4)
1
001557
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((1) and (2) in Fig.
A) and "Outside" 90° corners ((3) and (4) in Fig. A).
Measuring
Measure the wall length and adjust workpiece on
table to cut wall contact edge to desired length.
Always make sure that cut workpiece length at the
back of the workpiece is the same as wall length.
Adjust cut length for angle of cut. Always use
several pieces for test cuts to check the saw
angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw base
as indicated in the table (B).
In the case of left bevel cut
Molding
positionin
Fig. A
Bevel angleMiter angle
Foroutside
corner
Forinside
corner
52/38° type45° type
Right 31.6°
45° type
Left 33.9° Left 30°
52/38° type
Left 31.6° Left 35.3°
Right 35.3°
Right 35.3°Right 31.6°
(1)
(2)
(3)
(4)
Table(A)
006361
Molding
positionin
Fig. A
Molding edge against
guide fence
(1) Ceiling contactedge should
beagainstguide fence.
Ceiling contactedge should
beagainstguide fence.
For
outside
corner
Finished piece
will beonthe
Left side of
blade.
Finished piece
will beonthe
Right side of
blade.
Forinside
corner
Wall contactedge shouldbe
againstguide fence.
Finished piece
(2)
(3)
(4)
Table(B)
006362
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
• Tilt and secure bevel angle setting to
33.9° LEFT.
• Adjust and secure miter angle setting to
31.6° RIGHT.
1. Inside corner
2. Outside corner
1. Inside corner
2. Outside corner
1. 52/38 ﾟtype
crown molding
2. 45 ﾟtype crown
molding
3. 45 ﾟtype cove
molding

16
• Lay crown molding with its broad back
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
• The finished piece to be used will
always be on the LEFT side of the blade
after the cut has been made.
In the case of right bevel cut
Molding
positionin
Fig. A
Bevel angleMiter angle
Foroutside
corner
Forinside
corner
52/38° type45° type
Right 31.6°
45° type
Right 33.9° Right 30°
52/38° type
Left 31.6° Left 35.3°
Right 35.3°
Right 35.3°Right 31.6°
(1)
(2)
(3)
(4)
Table(A)
006363
Molding
positionin
Fig. A
Molding edge against
guide fence
(1)
For
outside
corner
Forinside
corner
Finished piece
(2)
(3)
(4)
Table(B)
Finished piece
will beonthe
Left side of
blade.
Finished piece
will beonthe
Right side of
blade.
Wall contactedge shouldbe
againstguide fence.
Wall contactedge shouldbe
againstguide fence.
Ceiling contactedge should
beagainstguide fence.
006364
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
• Tilt and secure bevel angle setting to
33.9° RIGHT.
• Adjust and secure miter angle setting to
31.6° RIGHT.
• Lay crown molding with its broad back
(hidden) surface down on the turn base
with its WALL CONTACT EDGE against
the guide fence on the saw.
• The finished piece to be used will
always be on the RIGHT side of the
blade after the cut has been made.
7. Wood facing
Use of wood facing helps to assure splinter-free
cuts in workpieces. Attach a wood facing to the
guide fence using the holes in the guide fence.
See the figure concerning the dimensions for a
suggested wood facing.
Over 15mm (5/8")Over 420mm (16-1/2")
11
50mm-60mm
(2"-2-3/8")
27mm (1-1/16")
85mm
(3-3/8")
70mm
(2-3/4")
85mm
(3-3/8")
70mm
(2-3/4")
002206
CAUTION:
• Use the straight wood of even thickness as the
wood facing.
WARNING:
• Use screws to attach the wood facing to the
guide fence. The screws should be installed
so that the screw heads are below the surface
of the wood facing so that they will not
interfere with the positioning of the material
being cut. Misalignment of the material being cut
can case unexpected movement during the cutting
operation which may result in a loss of control and
serious personal injury.
NOTICE:
• When the wood facing is attached, do not turn the
turn base with the handle lowered. The blade
and/or the wood facing will be damaged.
8. Cutting repetitive lengths
1
2
3
001846
When cutting several pieces of stock to the same
length, ranging from 220 mm to 385 mm, use of the
set plate (optional accessory) will facilitate more
efficient operation. Install the set plate on the holder
(optional accessory) as shown in the figure.
Align the cutting line on your workpiece with either the left
or right side of the groove in the kerf board, and while
holding the workpiece from moving, move the set plate
flush against the end of the workpiece. Then secure the
set plate with the screw. When the set plate is not used,
loosen the screw and turn the set plate out of the way.
NOTE:
• Use of the holder-rod assembly (optional
accessory) allows cutting repetitive lengths up to
2,200 mm approximately.
1. Set plate
2. Holder
3. Screw
1. Holes

17
9. Groove cutting
1
001563
A dado type cut can be made by proceeding as follows:
Adjust the lower limit position of the blade using the
adjusting screw and the stopper arm to limit the
cutting depth of the blade. Refer to "Stopper arm"
section described on previously.
After adjusting the lower limit position of the blade,
cut parallel grooves across the width of the
workpiece using a slide (push) cut as shown in the
figure. Then remove the workpiece material
between the grooves with a chisel.
WARNING:
• Do not attempt to perform this type of cut by using a
wider type blade or dado blade.
Attempting to make a
groove cut with a wider blade or dado blade could lead to
unexpected cutting results and kickback which may result
in serious personal injury
• Be sure to return the stopper arm to the
original position when performing other than
groove cutting. Attempting to make cuts with the
stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
result in serious personal injury.
Carrying tool
1
011300
012715
Make sure that the battery cartridge is removed. Secure
the blade at 0° bevel angle and the turn base at the full
right miter angle position. Secure the slide poles so that
the lower slide pole is locked in the position of the carriage
fully pulled to operator and the upper poles are locked in
the position of the carriage fully pushed forward to the
guide fence. Lower the handle fully and lock it in the
lowered position by pushing in the stopper pin.
Carry the tool by holding both sides of the tool base as
shown in the figure. If you remove the holders, dust bag,
etc., you can carry the tool more easily.
CAUTION:
• Always secure all moving portions before carrying
the tool. If portions of the tool move or slide while
being carried loss of control or balance may occur
resulting in personal injury.
WARNING:
• Stopper pin is only for carrying and storage
purposes and should never be used for any
cutting operations. The use of the stopper pin for
cutting operations may cause unexpected
movement of the saw blade resulting in kickback
and serious personal injury.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
WARNING:
• Always be sure that the blade is sharp and
clean for the best and safest performance.
Attempting a cut with a dull and /or dirty blade may
cause kickback and result in a serious personal
injury.
NOTICE:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
1. Miter angle
Push the carriage toward the guide fence and
tighten two clamp screws to secure the carriage.
Loosen the grip which secures the turn base. Turn the
turn base so that the pointer points to 0° on the miter
scale. Then turn the turn base slightly clockwise and
counterclockwise to seat the turn base in the 0° miter
notch. (Leave as it is if the pointer does not point to 0°.)
1. Stopper pin
1. Cut grooves with
blade

18
12
012585
Loosen the hex socket bolt securing the guide fence
using the hex wrench.
Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin. Square the
side of the blade with the face of the guide fence
using a triangular rule, try-square, etc. Then
securely tighten the hex socket bolt on the guide
fence in order starting from the right side.
1
002209
1
2
3
003942
Make sure that the pointer points to 0° on the miter
scale. If the pointer does not point to 0°, loosen the
screw which secures the pointer and adjust the
pointer so that it will point to 0°.
2. Bevel angle
(1) 0° bevel angle
Push the carriage toward the guide fence and
tighten two clamp screws to secure the
carriage. Lower the handle fully and lock it in
the lowered position by pushing in the stopper
pin.
2
1
5
4
3
012589
Loosen the lever at the rear of the tool.
Turn the 0° bevel angle adjusting bolt (lower
bolt) on the right side of the arm two or three
revolutions counterclockwise to tilt the blade
to the right.
1
2
3
001819
Carefully square the side of the blade with the
top surface of the turn base using the
triangular rule, try-square, etc. by turning the
0° bevel angle adjusting bolt clockwise. Then
tighten the lever securely.
123
011306
Make sure that the pointer on the arm point to
0° on the bevel scale on the arm holder. If it
does not point to 0°, loosen the screw which
secures the pointer and adjust the pointer so
that it will point to 0°.
(2) 45° bevel angle
1
012590
1. Left 45 ﾟbevel
angle adjusting
bolt
1. Bevel scale
2. Pointer
3. Screw
1. Triangular rule
2. Saw blade
3. Top surface of
turn table
1. Lever
2. Arm holder
3. 0 ﾟdegree
bevel angle
adjusting bolt
4. Arm
5. Release button
1. Screw
2. Miter scale
3. Pointer
1. Triangular rule
1. Guide fence
2. Hex socket bolt

19
Adjust the 45° bevel angle only after
performing 0° bevel angle adjustment. To
adjust left 45° bevel angle, loosen the lever
and tilt the blade to the left fully. Make sure
that the pointer on the arm points to 45° on
the bevel scale on the arm holder. If the
pointer does not point to 45°, turn the 45°
bevel angle adjusting bolt (upper bolt) on the
right side of the arm until the pointer points to
45°.
Replacing carbon brushes
1
001145
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
1
2
011307
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
After use
• After use, wipe off chips and dust adhering to the
tool with a cloth or the like. Keep the blade guard
clean according to the directions in the previously
covered section titled "Blade guard". Lubricate the
sliding portions with machine oil to prevent rust.
• When storing the tool, pull the carriage toward you
fully so that the slide pole is thoroughly inserted into
the turn base.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
WARNING:
• These Makita accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments may result in serious
personal injury.
• Only use the Makita accessory or attachment
for its stated purpose. Misuse of an accessory or
attachment may result in serious personal injury.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Carbide-tipped saw blades
• Vise assembly (Horizontal vise)
• Vertical vise
• Holder set
• Holder assembly
• Holder rod assembly
• Set plate
• Dust bag
• Triangular rule
• Hex wrench
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
1. Brush holder cap
2. Screwdriver
1. Limit mark

20
Makita Corporation
www.makita.com
885295A4