Malide MLD-B03 User manual

R
User's Manual
使用说明书
MLD-B03 MLD-R01 &

目录
Contents
产品介绍
注意事项
配件清单
装车说明
安装步骤
更换电池
传感器配对步骤
太阳能语音显示屏绑定
App更多功能介绍
规格参数
常见问题及解决方法
产品保修
2
2
3
3
4
4
5
6
8
9
10
10
7
Product Introduction
Precautions
List of Accessories
Instruction for Installation
Procedures of Installation
Battary Repalcement
Matching Procedures for Sensors
Binding of Solar Voice Display
Introduction for More App Function
Specification
Common Problems and Solutions
Warranty
太阳能语音显示屏说明
Instruction of Solar Voice Display

产品介绍
马力德蓝牙胎压监测系统(Malide BLE Tire Pressure Monitoring System,以下简称:Malide TPMS)可实时监测汽车轮胎的胎压
与胎温,并可通过App 精确显示数值。若胎温胎压发生异常，App会通过语音及警示图标及时向您发出警报。
Product Introduction
Malide BLE Tire Pressure Monitoring System (hereinafter referred to as Malide TPMS) can monitor the pressure and temperature of
car’s tire,and the value can be correctly displayed through App.If the abnormalities occurs on the tire’s pressure and temperature,the
App will send the alarm to you through the voice and warning icon.
注意事项
Precautions
Users should match the sensor and APP before driving, please do not match during
This product performs the wireless signal transmission. If the
If the temperature and pressure of tire display abnormally, please drive your car to the
If the sensor is not used properly due to the use of a gas-filled puncture sealant or other
the driving to avoid the unnecessary property
losses and personal injuries, otherwise,you will undertake the all the responsibilities and risks.
environment of wireless communication is special, the installation method
is incorrect or there are other special signal will be reduced or lost.
repair shop where it is closer to you for inspection
When indicate that the battery is too low, please replace the battery or the sensor in time to avoid the abnormal operation of tire pressure
external human factors, or the accident occurs,
the company will not bear any responsibility.
1、使用者应在行车前将传感器与App配对好,切勿在行驶中进行配对，以免造成不必要的财产损失和人员伤亡，否则您将承担所有责任与风险。
2、此产品进行无线信号运输，若无线通信环境特殊、安装方式有误或者其他特殊原因，无线信号有可能受到干扰而导致信号衰减或者丢失。
3、若胎温胎压显示异常，请及时将车辆驾驶到附近维修店进行检查维修，以免发生意外。
4、当提示电池电量过低时，请及时更换电池或传感器，以免因电量过低导致胎压监测系统不能正常工作。
5、若因使用气嘴填充的补胎剂或其它外在人为因素而导致传感器不能正常使用，或因此导致发生事故，本公司将不承担因此造成的任何责任。
reasons, the wireless signal may be interfered and the
and repair to avoid the accident.
detection system due to low battery.

Nut ×4 Bottom Cover ×4
Battery ×4
Sensor ×4
Wrench×1
Solar Voice Display×1
List of Accessories
Instruction for Installation
on the Car
When the product leaves the factory, the sensors and ID codes of four tires have been configured (each sensor has an independent ID code), just
配件清单
防盗螺母×4 防拆底盖×4 纽扣电池×4 太阳能语音显示屏×1 传感器×4 扳手×1
装车说明
产品出厂时，已经配置好四个轮胎的传感器及ID码（每套传感器都有独立ID码），只需先将传感器安装至相应的位置轮胎上，即可使用；
若想用手机App查看数据，需先把传感器与手机App配对好（配对方法详看“传感器配对步骤”）。
need to install the sensor to the corresponding
左前左后
右后
LR LF
RR 右前 RF
positions of tires, and use it.You need to match the App with sensors first when you want to watch
Matching Procedures for Sensors" for the matching method).
the datas(See the "
充电线×1
Charging Cable×1
信号传输
信号传输

Tighten the nut anticlockwise by
wrench
Screw the nut anticlockwise
by hand
Remove the bottom cover and
disassemble the case of the sensor
by wrench
Or disassemble the case of the
sensor by the bottom cover if
the wrench is lost
Remove the old battery and
install a newone (positive pole
upward),then reinstall the
sensor according to the Inta-
above
Procedures of Installation
安装步骤
Screw the nuts to the bottom
of the valve core
A、拧入防盗六角螺母
Screw the sensors tightly
B、拧紧传感器 C、用手将防盗六角螺母逆时针方
向拧紧,顶着传感器底部
D、用扳手逆时针拧紧防盗六角螺母
Battery Replacement
更换电池
Screw the nu t clockwise to separate
it from the sensor by wrench and
then screw out the by hand
sensor
A、用扳手顺时针方向旋转六角螺母，
将其与传感器分离，再逆时针方
向旋转传感器
B、取下防拆底盖，用扳手扣紧传
感器，并逆时针旋转以拆开传
感器外壳
C、若扳手丢失或损坏，可将防拆
底盖取下并方向扣紧传感器，
逆时针旋转拆开传感器
D、取出旧电池并装上新电池（正
极朝上），最后按照安装步骤
重新将传感器安装好
llation steps

Matching Procedures for Sensors
Click the symbol in the upper right corner of the
Click "Binding new device" to enter the interface
Manual matching: Click the tire selection box to
QR matching: Click the tire selection box to enter
main interface of Figure A
to enter the system setting interface, as shown in Figure B.
shown in Figure C.
be matched, input the ID
engraved on the sensor and click to complete the matching.
the scanning code state,
scan the QR code on the sensor shell. As soon as the scanning is completed,
the matching will be completed.
传感器配对步骤
1、点击图A主界面右上角设置符号，进行系统设置界面，如图B所示
2、点击“绑定新设备”，进入图C所示界面
3、手动匹配：点击需配对的轮胎选框，输入传感器上雕刻的ID再点击即可完
成配对
4、QR匹配：点击需配对的轮胎选框进入到扫码状态，扫描传感器外壳上的二
维码，扫描成功即可完成配对
AB
D
CEF
车辆1
? ?
??
系统设置
语音提醒
语言 简体中 文
车辆设定
系统参数 设定
绑定新设备
调胎设定
配套设备 绑定
日志报告
帮助
手动匹配
自动匹配
QR匹配
绑定新设备 手动匹配
? ?
??
?
说明
点击要配对的轮胎选框，手动输入设备
码，点击确认完成该轮胎绑定
ID
我知道了
自动匹配
? ?
??
?
说明
点击要配对 的轮 胎选 框， 进入1 20秒 倒计
时搜索,搜索到设备后ID码 自动 显示,
点击确认完成该轮胎绑定
我知道了
QR匹配
? ?
??
?
说明
点击要配对 的轮 胎选 框， 成功 扫描 产品
二维码后将自动绑定ID
我知道了
说明：当传感器与手机配对好时，手机并未能收到数据，需进一步通过
手机和太阳能语音显示屏绑定方能收到相关数据。
Note:When the sensor is paired with the phone, the phone does not
receive the data.The data needs to be received through the binding of the
mobile phone and the solar voice display.

After binding the ID codes of all the tires, click the upper right corner
After entering the interface of Figure B, click on “Supporting Device
After entering the interface of Figure C, click on “Searching for Device”
Shortly press the button to turn on the solar voice display,
When the "MLD_R01" key in Figure D appears, click this button to bind.
When the “Binding Successful” voice is heard and the prompt box in
of the main interface to set the symbol
Binding”.
to find the solar voice display.
then press button for 5 seconds untilthe token
“ ”on the display screen flickers. Then the solar voice display enters the
Figure E appears, the solar voice
display is bound, and finally click “I Know” to exit the prompt box.
Binding of Solar Voice Display
太阳能语音显示屏绑定
1、绑定好所有轮胎的ID码后，点击这界面右上角设置符号进入图A界面;
2、进入图B界面后，点击“配套设备绑定”;
3、进入图C界面后，点击“搜索设备”以查找太阳能语音显示屏;
4、短按按钮开启太阳能语音显示屏,然后长按太阳能语音显示屏按键约5秒，直到显示屏幕上的" "标志交替闪烁，
此时太阳能语音显示屏进入配对模式;
5、当出现图D中的“MLD_R01”按键时,点击此按键进行绑定;
6、当听到“绑定成功”语音且出现图E中的提示框时,太阳能语音显示屏绑定成功,最后点击"我知道了"退出提示框;
A
BCDE
系统设置
语音提醒
语言 简体中 文
车辆设定
系统参数 设定
绑定新设 备
调胎设定
配套设备 绑定
日志报告
帮助
配套设备绑定 ?
搜索设备
?
搜索中...
MLD_R01
配套设备绑定 配套设备绑定 ?
搜索设备
完成
资料发送成功
我知道了
to enter the interface A.
matching mode.

太阳能语音显示屏说明
1、按键说明
开机：短按“ ”按键
关机：短按“ ”按键约一秒
进入配对模式：长按按键“ ”约五秒并等显示屏信号“ ”标志闪烁
2、显示屏功能说明
Turn on:Short press button“ ”
Turn off:Press the button “ ” for about a second
Button Description
Function Description of Display
(1)胎压过低警报
当胎压低于1.9Bar，“语音警报“左前（左后/右前/右后）轮胎气压
过低”将会播放，显示屏对应的轮胎胎压数据会一直闪烁。
Low Pressure Alarm
When tire pressure is below 1.9 Bar, the voice alarm "left front (left rear / rightfront /
right rear) tire pressure is too low" will be played, and the TPMS data corresponding
to the display screen will flicker.
(2)胎压过高警报
当胎压高于2.8Bar，语音警报“左前（左后/右前/右后）轮胎气压
过高”将会播放，显示屏对应的轮胎胎压数据会一直闪烁。
High Pressure Alarm
When tire pressure is higher than 2.8 Bar, the voice alarm "left front (left rear / right
front / right rear) tire pressure is too high" will be played, and the TPMS data
corresponding to the display screen will flicker.
(3)胎温过高警报
当胎温高于 65℃，语音警报“左前（左后/右前/右后）轮胎温度过高”
将会播放，显示屏对应的轮胎胎温数据会一直闪烁。
High Temperature Alarm
When tire temperature is higher than 65℃, the voice alarm "left front (left rear /right
fron t / rig ht rear) tire temperature is too high" will be played, and the TPMS data
corresponding to the display screen will flicker.
(4)快速漏气警报
当轮胎发生快速漏气，语音警报“左前（左后/右前/右后）轮胎
漏气”将会播放，显示屏对应的轮胎胎温数据会一直闪烁。
Fast L eak A larm
When the tire fast leaks , the voice alarm " left front (left rear/right front/right rear)
tireleakage" will be played, and the tire temperature data corresponding to the
display screen will flicker.
(5)发射端电量过低警报
当发射端电量过低时，语音警报“左前（左后/右前/右后）轮胎电量过
低”将会播放，显示屏对应的轮胎会一直闪烁。
Sensor Battery Alarm
When the Sensor battery is too low, the voice alarm "Left front (left rear / right front /
right rear) tire battery is too low" will play, the tire corresponding to the display will
flicker.
(6)显示屏电量过低警报
当显示屏电量过低时，显示屏上的电量标志" "会一直闪烁。
Display Battery Alarm
When the display battery is too low, the battery token “ ”on the display will flicker.
(7)进入配对模式
Enter Pairing Mode
When the display button is pressed for about 5 seconds to enter the pairing mode, the
signal token “ ” o f the d isplay will flicker.
当长按显示屏按键5秒左右进入配对模式，显示屏的信号标志“ ”将会
闪烁。
(8)太阳能充电模式
Solar Energy Charging Mode
When the display is solar-charged, the sun token “ ”on the display remains
stea dy and the battery token “ ”is displayed charge status.
当显示屏进行太阳能充电时,显示屏上的太阳标志“ ”保持常亮,电池
标志“ ” 显示充电状态。
(9)USB充电模式
USB Charging Mode
When the display is USB charging, the battery token“ ” on the display shows the
charging status.
当显示屏进行USB充电时,显示屏上的电池标志“ ”显示充电状态。
说明:
当TPMS存在某一轮胎或者多个轮胎出现胎压或胎温异常时，显示
屏的汽车标志上的胎压标志“ ”将会一直闪烁并进行相关显示和语音播
放。当所有轮胎的胎温胎压正常时，显示屏将会播放“胎温胎压正常，祝
您一路平安！”并显示相关实时数据。
Instruction of Solar Voice Display
note :
When TPMS has abnormal tire pressure or tire temperature in one or more tires,
the tire pressure token“ ” on the display screen will flicker and display data and voice
play.When the tire temperature and temperature of all tires is normal, the display will
play“Tire pressure and temperature are normal, have a nice trip!” and display
relevant real-time data.
Enter pairing mode:Press the button “ ”for about five seconds and wait for “ ”
in the display to flicker.
显示屏幕
display screen
按键
Burron
太阳能板
Solar panels
USB充电口
USB charging port

Introduction for more APP functions
In the setting interface of system, click the vehicle setting to enter the setting interface of
In the setting interface of system, click "System Parameter Setting" to enter the setting
In the setting interface of system,click “Setting of Tire Adjustment” to enter the setting
Click "Help" in the setting interface of system to enter the help interface as shown in Figure D.
vehicle as shown in Figure A, you can set the
picture, name and type of vehicle as well as license numbers.
interface of system parameter as shown in Figure B,
you can either define the temperature and pressure range of the front and tires according to the actual situation, or can replace the display
interface of tire adjustment as shown in Figure C,
you can change the display frame according to the actual sensor position.(You can click on the instruction symbol in the upper right corner to
Here you can view the installation instruction
App更多功能介绍
1、在系统设置界面中，点击“车辆设定”进入到车辆设定界面，如图A所示，您可以对车辆图片、车辆名称、车辆型号和车牌号码进行设定。
2、在系统设置界面中，点击“系统参数设置”进入到系统设置界面，如图B所示，您可以根据实际情况对前后轮的胎温胎压范围进行定义，
也可更换显示单位或者恢复默认设置。
3、在系统设置界面中，点击“调胎设定”进入到调胎设定界面，如图C所示，您可以根据实际传感器位置进行显示框换位（可点击右上角的
说明符号进行换位操作学习）
4、在系统设置界面中，点击“帮助”进入到帮助界面，如图D所示，此处您可以查看设备安装说明及App使用说明。
ABCD
车辆设定 ?
车辆名称
车辆型号
车牌号码
车辆1
奔驰
粤A 88888
系统参数设置 ?
胎压上限
胎压单 位选 择
kPa psi Bar Kg/cm²
6.4
胎压下限 1. 9
前轮
后轮
胎压上限 2. 8
胎压下限 1. 9
℃℉
温度单位选择
胎压下限 65
胎压下限 65
前轮
后轮
恢复默认设置 ＞
车辆1
1 2
43
00000
--Kpa
--℃
00001
--Kpa
--℃
00003
--Kpa
--℃
00002
--Kpa
--℃
帮助
设备安装说明
APP使用说明
unit or restore the default settings.
learn the transposition operation)
of equipment and the use instruction of App.
说明：语音显示屏的相关参数通过手机App修改设置。当每次进行系统参数设置、调胎设定、传感器绑定更新操作后，需重新绑定语音
显示屏以更新设置。
Note:The relevant parameters of the voice display are modified by the mobile phone App.After setting system parameter , setting tire
adjustment, or updating sensor binding operation, you need to rebind the voice display to update the settings.

Parameter
Item
Working Voltage
Sleeping Current
Storage Temperature
Working Temperature
Working Humidity
Working Frequency
Battery Capacity
Service Life Of Battery
Weight
Specifications
规格参数
项目 参数
工作电压
睡眠电流
存放温度
工作温度
工作湿度
工作频率
胎压监测范围
胎温监测范围
电池容量
电池使用寿命
重量
2.4V-3.3V
＜3.0uA
-40℃-85℃
-40℃-85℃
95%(MAX)
434Mhz
0-640kpa(0-6.4Bar)
-40℃-80℃
140mA(CR1632)
8.8g±0.5g
Monitoring range of tire pressure
Monitoring range of tire temperature
(Driving four hours per day)
About 2 years
（按每天行驶四小时）
约二年

Common Problems And Solutions
Warranty
常见问题及解决方法
After the sensor is just matched or the App is opened, there is no data display on the main interface.
First determine if the display is bound.And the sensor will only send data in the following situation:
No voice broadcast from the App.
①Within 20 minutes after the battery is installed; ②The driving speed exceeds 20 yards; ③The parking time is within 10 minutes;
④The tire pressure changes instantaneously more than 30 kPa; ⑤The tire rotates for more than 20 seconds.
When the other time is in the sleeping state, the data will not be sent in sleeping state,so the receiver will not receive the signal.
Check if the voice alert is on in the setting interface of system; check if the phone is muted or the volume is low.
No sound in the solar voice display.
Confirm that the voice displayer has completed the binding; the voice displayer will not broadcast if there is no abnormality.
1、刚配对好传感器或者打开App后，主界面无数据显示。
首先确定是否绑定好显示屏。传感器只有在刚装电池的20分钟内、行车速度超过20码、停车10分钟内、轮胎气压瞬间变化超过30kPa
或者轮胎转动超过20秒时，
才会发送数据，其他时间处于睡眠状态，睡眠状态不发送数据，因此接收端也不会接收到数据。
2、App没有语音播放。
检查App系统设置界面中"语音提醒"是否处于打开状态;检查手机是否处于静音状态或音量较低状态。
3、太阳能语音显示屏没有声音
确认语音显示屏是否已经完成绑定；无异常时语音显示屏不会播放。
产品保修
非常感谢您对本公司的支持，本产品自购买之日起将有一年的保修期。在保修期间，若产品在正常使用情况下出现质量问题导致无法正
常使用，本公司将承担产品维修或更换责任，提供维修或更换的产品需满足以下条件：
●产品质量问题的原因是出厂的不良品；
●产品按照正常的使用方法；
●产品未经不正当拆解；
●需维修或更换的产品需提供给购买的商家，并说明损坏原因和购买日期。
Thank you very much for supporting our company. This product will have one year warranty
● The cause of product quality problems is defective products from the factory;
● The product is in accordance with normal usage methods;
● The product has not been improperly dismantled;
● If the product need to be repaired or replaced, they need to be sent to the merchant and
from the date of purchase.During the warranty
due to quality problems under normal use, the company will be responsible for the repair or
conditions:
explained the reasons of damage and
period, if the product fails to function properly
replacement of product.Products that are repaired or replaced must meet the following
purchase date.

FCC Statement
-This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-• Reorient or relocate the receiving antenna.
-• Increase the separation between the equipment and receiver.
-• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-• Consult the dealer or an experienced radio/TV technician for help.
-Caution: Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate this equipment.
-This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
-
-RF Exposure Information
-
The device has been evaluated to meet general RF exposure requirement. The device can be use d in
portable exposure condition without restriction.
11

Manufacturer：Shenzhen Malide Technology Co. Ltd.
Android App Download IOS App Download
Address: Building A, No. 26, Xin'e Industrial Zone, Egongling Community,
Pinghu Street, Longgang District, Shenzhen, China
安卓App下载 苹果App下载
制造商：深圳市马力德科技有限公司
地址：深圳市龙岗区平湖街道鹅公岭社区信鹅工业区26号A栋
公司网址(Company Website)：http://malide.com.cn/
邮箱(Email)：[e-mail]