Mamava Solo User manual

Mamava, the leading expert in lactation space design, provides dignified lactation
accommodations and breastfeeding resources for employers and organizations
around the world. Our mission is to create a healthier society through
infrastructure and support for breastfeeding.
Certified B Corporation, Assembled in U.S.A.
The curved lactation suite design is a TM/SM of Mamava, Inc. All rights reserved.
[e-mail]
[phone]
Assembly Guide
| Solo and Solo Base
Shipping crate dimensions:
7’10” W x 4’7” D x 2’5” H
Assembled pod dimensions:
4’ W x 4’ D x 7’4” H
It should take 2 people approximately
1.5 hours to assemble this Mamava pod.
Mamava Solo
Mamava Solo Base
Table of Contents
Tools + Hardware.................................................................................................................................................................................................................. Pg. 2
Parts .......................................................................................................................................................................................................................................... Pg. 3
Warnings ................................................................................................................................................................................................................................. Pg. 4
Markings .................................................................................................................................................................................................................................. Pg. 5
Shipping Crate ...................................................................................................................................................................................................................... Pg. 6
Foundation ............................................................................................................................................................................................................................. Pg. 7
Wall Plug Wiring................................................................................................................................................................................................................... Pg. 9
Wall Panels + Door ............................................................................................................................................................................................................ Pg. 10
Roof Frame........................................................................................................................................................................................................................... Pg. 16
Wiring + Lighting ............................................................................................................................................................................................................... Pg. 19
Roof Panel.............................................................................................................................................................................................................................. Pg. 21
Seat.......................................................................................................................................................................................................................................... Pg. 22
Shelf + Laptop Desk.......................................................................................................................................................................................................... Pg. 24
Final Assembly + Testing ................................................................................................................................................................................................ Pg. 27
Notes....................................................................................................................................................................................................................................... Pg. 29

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 2
Tools + Hardware
Not included
Provided
2-6’ step ladder
Adjustable wrench
Flat head screwdriver Phillips head #2 screwdriver
5 mm hex key
Light working gloves
(Up to 17mm)
*For crate disassembly only
(16370)
(22) M8 x 55
Flange Head Bolt
(17240)
(2) #8 x 5/8”
Phillips Pan Head Screw
(4) M8 x 20
Button Head Cap Screw
(16835)
(11) M8 x 35
Button Head Cap Screw
(16840)
(2) 1/4” x 2”
Phillips Pan Head Screw
(16870)
Cordless drill
with #2 Phillips bit
(16980)
5/32” hex key

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 3
Parts
16350
14980
17160
16765
16615
16715 16770
16710
16700
16705
16595
15015
16355 / 17180
14915
14955
15065 /17175
15450
PART NUMBER PART
14915 Roof Panel
14955 Left Wall Panel
14980 Back Wall Panel
15015 Right Wall Panel
15065 (Solo Base) Door
17175 (Solo)
15450 GFCI Plug
16350 Base
16355 (Solo Base) Roof Frame
17180 (Solo)
PART NUMBER PART
16595 Seat Back
16615 Shelf
16700 Seat Frame Right Side
16705 Seat Frame Left Side
16710 Seat Base
16715 Seat Frame Front
16765 Light Fixture
16770 Laptop Desk
17160 Wire Cover
17215 Caster Wheels (optional)

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 4
Warnings
To reduce the risk of electrical shock:
Always unplug this furnishing from the electrical outlet before cleaning or servicing.
Connect the power cord to a properly grounded outlet only.
Do not use the pod if you notice any defects to electrical equipment.
Read and understand the assembly guide and all safety
instructions before assembly and use of this equipment.
Only assemble with tools as described in this assembly
guide. Use of power tools in place of hand tools will
damage hardware.
The weight of many components exceeds 40 lb. Two
person lift required.
Do not climb on top of the pod, or place any load on the
roof of the pod.
Protective gloves should be worn during assembly,
maintenance, or disassembly.
Unplug from outlet before putting on or taking o parts.
Close supervision is necessary when this furnishing is
used by, or near children or disabled persons.
Use this furnishing only for its intended use as described
in these instructions.
Do not use attachments not recommended by the
manufacturer.
Never operate this furnishing if it has a damaged cord
or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the
furnishing to a service center for examination or repair.
Keep the cord away from heated surfaces.
Never operate the furnishing with the air openings
blocked. Keep the air openings free of lint, hair, and the
like.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being
used or where oxygen is being administered.
To disconnect, turn all controls to the o position, then
remove the plug from the outlet.
Use care when raising and lowering the laptop desk. The
space between the desk and the shelf can be a pinch
point.
Keep children away from moving laptop desk.
Connect this furnishing to a properly grounded outlet
only.
For loading always put heavier items at the bottom and
not near the top in order to help prevent the possibility
of the furnishing tipping over.
Mount furnishings at the correct height.
Mount only approved work surfaces and secondary
surfaces (shelves) in accordance with instructions.
Failure to do so may cause instability, collapse, or failure
of electrical components.
Maximum load for the laptop desk is 70 lb (31 kg).
Maximum load for the seat is 300 lb (136 kg).
Maximum load for the shelf is 80 lb (36 kg).
Maximum load for the coat hook is 15 lb (7 kg).
Electrical ratings for the pod:
Branch Circuit: 120 vAC/ 15 A / 50-60 Hz
Pod: 12 vDC / 7 A
Outlet: 120 vAC / 13.3 A
To reduce the risk of burns, fire, electric shock or injury to persons:

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 5
Markings
Risk of fire and shock
Use only SJ00W type 12 AWG cord
WARNING
Risk of tip
over
Max 15 lb.
load
WARNING
Risk of tip over
Max 80 lb. load
WARNING
Risk of tip over
Max 70 lb. load
WARNING
Risk of Electric
Shock, Fire and
Injury
Review the assembly
instructions to
confirm the
appropriate critical
components and
accessories are being
used with the
furnishing.
WARNING

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 6
Locate the serial number sticker
on the exterior of the crate. It
begins with #XXXX followed
by Solo or Solo Base. Follow
assembly instructions based on
your model.
1. Use a cordless drill with a #2
Phillips bit to remove the screws
from the crate cross braces. Set
aside the cross braces.
2. Remove the screws from the end
panels of the crate. Set aside the
end panels.
3. Remove the screws from the side
panels of the crate. Set aside the
side panels.
Shipping Crate
TOOLS AND PARTS
• Cordless drill with a #2 Phillips bit

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 7
1. Unpack the base (16350) from
Box 2: Base.
Protect the vinyl side of the base
by setting it face down on leftover
cardboard packaging.
2. If you ordered accessory caster
wheels (17215), remove them from
Box 9: Caster Wheels.
Use a 5 mm hex key to fasten all 4
caster wheels to the bottom of the
base with M8 x 20 button head cap
screws (16835) (4 per wheel).
Foundation
TIP: Assemble the Mamava Solo pod as close to its final location as possible. Once a location is selected,
ensure the floor is level and there aren’t any gaps greater than 1” between the bottom of the level and the floor.
TOOLS AND PARTS
• 5 mm hex key (provided)
• Adjustable wrench
• Base (16350)
• Caster Wheels (17215) + (16) M8 x 20 Button Head Cap
Screws (16835) (optional)
X16

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 8
3. Flip the base over, so that the
vinyl side is facing up and the
cardboard is removed.
4. Adjust leveling feet by rotating
them clockwise by hand until they
are in contact with the floor. Make
sure the base is stable.
If the base wobbles, adjust the
height of the leveling feet.
*If installing caster wheels, adjust
the leveling feet so they extend an
inch beyond the caster wheels.
5. Lock each foot in place by
tightening the M8 nut with an
adjustable wrench until flush with
the frame of the base.
If you have trouble tightening the
nuts, turn the base on its side. Once
nuts are tight, return the base back
to its position and ensure that it’s
stable.

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 9
1. Unpack the GFCI plug cord
(15450) from the plastic bag
of parts.
Route the orange end of the
GFCI cord up through the
round hole in the base leaving
approximately 2’ of cord inside.
Leave the GFCI plug outside the
pod.
2. Check that the GFCI plug can
reach the nearby outlet, but don’t
plug in yet.
Wall Plug Wiring
TOOLS AND PARTS
• GFCI Plug (15450)

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 10
1. Unpack the back wall panel
(14980) from Box 3: Wall Panels.
Set the bottom of the back wall
panel inside the back channel
of the base at a 45° angle, then
straighten into place. The aluminum
flange on the pod base should be
visible at the bottom of the wall.
The screw holes at the bottom of
the back wall panel should line up
with the notches in the aluminum
flange.
Once in place, one person should
continue to hold the wall panel.
2. Use a flat head screwdriver to
fasten the back wall panel to the
base with (2) M8 x 55 flange head
bolts (16370). If the bolt doesn’t
tighten, you may need to adjust the
alignment of the wall panel. Loosely
tighten for now, you’ll secure later.
Wall Panels + Door
TOOLS AND PARTS
• Flat head screwdriver
• Phillips head screwdriver
• (16) M8 X 55 Flange Head Bolt (16370)
• (2) #8 x 5/8” Phillips Pan Head Screw (17240)
• Back Wall Panel (14980)
• Left Wall Panel (14955)
• Right Wall Panel (15015)
• Door (15065)
• Door Handle
• Coat Hook (11130)
X2

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 11
3. Unpack the left wall panel
(14955) from Box 3: Wall Panels.
With the white side of the left wall
panel facing the interior, place the
bottom of the wall panel into the
left channel and push the panel
towards the back of the pod until
flush with the back wall panel.
The holes should line up with the
notches in the aluminum flange.
4. Use a flat head screwdriver to
fasten the left wall panel to the
foundation and back wall with (4)
M8 x 55 flange head bolts (16370).
Start from the top left to ensure the
pod wall is stable. Loosely tighten
for now, you’ll secure later.
Insert first
bolt here
Drop down first
Then slide back
X4

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 12
5. Remove the coat hook (11130)
from the plastic bag of parts.
Align the two holes in the coat
hook with the two holes on the left
wall.
Use a Phillips head screwdriver to
attach in place with (2) #8 x 5/8”
Phillips pan head screws (17240).
X2

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 13
6. Unpack the right wall panel
(15015) from Box 3: Wall Panels.
With the white side of the right
wall panel facing the interior, place
the bottom of the wall panel into
the right channel and slide the
panel towards the back of the pod
until flush with the back wall panel.
The holes should line up with the
notches in the aluminum flange.
7. Use a flat head screwdriver to
fasten the right wall panel to the
base and back wall panel with (4)
M8 x 55 flange head bolts (16370).
Start from the upper right to
stabilize the pod. Loosely tighten
for now, you’ll secure later.
Insert first bolt here
Drop down first
Then slide back
X4

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 14
8. Unpack the door (15065 or 17175)
from Box 4: Door and the door
handles from the plastic bag of
parts.
Slide the door handle onto the
body of the lock (or interior
housing for the Solo Base model)
until it clicks. Repeat this step for
the interior handle.
If your pod has a Schlage lock on
the door with a keypad, you have
a Solo model. Pods with a keyless
handle are Solo Base models.
Follow respective directions
throughout this guide.
9. Place the door on the base so
that the bottom aluminum flange
sits on top of the threshold and the
aluminum corners align with the
left and right wall panels.

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 15
10. Use a flat head screwdriver to
fasten the door to the left and right
walls with (4) M8 x 55 flange head
bolts (16370). Fasten the top left
and right bolts first, then fasten the
lower left and right bolts. Loosely
tighten for now, you’ll secure later.
It may be helpful to have a second
person push on the door and/or
side walls to help line up the holes.
11. Use a flat head screwdriver to
fasten the door to the base with (2)
M8 x 55 flange head bolts (16370).
To access the second hole, open
the door by entering 8008 on the
keypad. Keep the door propped
open. It may be helpful to use the
deadbolt to do so. Loosely tighten
for now, you’ll secure later.
Insert first
bolt here
Insert second
bolt here
X4
X2

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 16
1. Set up your ladder behind the
pod.
Unpack the three-sided roof frame
(16355 or 17180) from Box 5: Roof.
Remove the roof panel (14915) from
the roof frame and set aside.
*If you have the Solo Base model,
skip ahead to step 3.
2. Remove the antennas from the
plastic parts bag taped next to the
PCD.
Attach the two antennas to the top
of the Pod Control Device (PCD),
with the shorter antenna closest
to the power cord. Once secured,
keep the antennas upright.
Roof Frame
TOOLS AND PARTS
• Flat head screwdriver
• BLE and LTE Antennas
• (6) M8 X 55 Flange Head Bolt (16370)
• Roof Frame (16355 or 17180) / Roof Panel (14915)

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 17
3. Orient the roof frame with the
fan towards the back wall panel.
The antennas should face the
ceiling (not applicable to the Solo
Base model).
Hand the roof frame over the top
of the pod to the person on the
ladder. At this point, it’s useful to
have a third person help lift it.
4. Slide the roof frame inside the
top of the wall panels until the
aluminum flange caps the top of
the wall.
Ensure the wires hang inside at the
back left corner of the pod.
5. Use a flat head screwdriver to
secure the roof frame to the left,
back and right walls with (6) M8
x 55 flange head bolts (16370).
Loosely tighten as the bolts will be
fully secured in the next step.
X6

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 18
6. Once the roof frame is in place,
use the flat head screwdriver to
fully tighten all of the exterior M8
x 55 flange head bolts (16370).
Bolts should be secure, but stop
tightening if the wall panels begin
to dimple.
If you have the Solo Base model,
skip ahead to the Wiring +
Lighting.
7. Connect the two wires at the top
left of the door frame and the two
wires at the top right of the door
frame. Then tuck them into the
channel.
X22

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 19
1. Enter the pod (use keypad code
8008 if your door isn’t propped
open.)
Uncoil the black power cord from
the back left corner of the roof
frame and let it drop to the floor.
Uncoil the red and black wire from
the back left corner of the roof
frame.
2. Remove the aluminum wire cover
(17160) from Box 4: Door.
Insert the loose end of the red and
black wire through the hole at the
top of the wire cover. Make sure the
black power cord is hanging behind
the wire cover.
3. Snap the wire cover into the
back left corner and slide it up until
it touches the roof frame.
Wiring + Lighting
TOOLS AND PARTS:
• 5 mm hex key (provided)
• (3) M8 x 35 Button Head Cap Screw (16840)
• Light Fixture (16765)
• Wire Cover (17160)

221027
[e-mail] • [phone] • 180 Battery St, Suite 210, Burlington, VT 05401
| Solo 20
4. Remove the light fixture (16765)
from Box 1: Assembly Guide +
Hardware.
Place into position at the top of the
back wall with the plug towards the
left wall. The three holes in the light
fixture should line up with the three
holes in the back wall.
5. While one person holds the light
fixture, use a 5 mm hex key to
fasten it to the back wall using (3)
M8 x 35 button head cap screws
(16840). It’s helpful to use a small
step stool inside the pod or a
ladder outside the pod.
6. Connect the two wires in the left
corner of the light fixture.
X3