Siemens SIREMOBIL Compact User instructions

SIREMOBIL Compact
Register 3 English
Print No.: RXR2-130.033.02.02.02 Doc. Gen. Date: 03.97
Replaces: RXR2-130.033.02.01.02
© Siemens AG 1997
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights,
including rights created by patent
grant or registration of a utility
model _or_design,_are_reserved.
SP
Installation and Setting Instructions
Connecting laser camera 37 79 159 G5429

SIREMOBIL Compact Register 3 RXR2-130.033.02 Page 2 of 8 Siemens AG
Rev. 02 03.97 TD SP 1 Medical Engineering
2 Connecting laser camera1
General 1
Safety Information 1
Tests or settings performed using radiation are indicated by the radiation symbol .
Radiation protection clothing must be worn when performing such procedures.
Protective Conductor Measurement 1
After all work has been completed and all covers have been attached, perform a protec-
tive conductor measurement according to TI 236 / ARTD-002.731.17...
The protective conductor resistance must not exceed 0.2 Ohm.
Additional note 1
These instructions apply only to connecting a laser camera to a SIREMOBIL Compact.
Parts required 1
Measurement devices and auxiliary materials required 1
Tools required 1
•Standardtoolkit(refertoARTD/section3)
•1setof Allen keys
•Heatgun
•Drill
•17 mm drill bit
•16 mm drill bit
•3mm drill bit
Ensure compliance with the product-specific safety information in the
documents as well as the general safety information found in Register 2
of the TI folder.
•Lasercameraconnectionkit 37 79 159 G5429
•ServicePC
•DigitalMultimeter DMM
•ServiceSoftware(fromlogbook)
•CableforconnectingservicePC to host 99 00 440 RE999
•Protectiveconductormeter 44 15 899 RV 090
CAUTION

Connecting laser camera 3
Siemens AG Register 3 RXR2-130.033.02 Page 3 of 8 SIREMOBIL Compact
Medical Engineering Rev. 02 03.97 TD SP 1
Mechanical installation of the video separator device 1
•Installthevideo separatordevice(OTV)asindicatedinFig.1.
Usethemountingbracketand secureit with the two threaded bolts.
Thevideosocketsshouldpointtowardthebackofthemonitortrolley.
Installing the isolated video socket and remote release socket 1
•Drill two holes usingthedimensionsindicated in Fig. 2. The left one should be 17 mm for
thevideosocketandtherightone should be 16mm for the remote release socket.
•Inserttheremoterelease socketintherightholeas a drilling templateandthen drillboth
ofthe3 mm attachment holes.
•Installthe videosocketaccordingto Fig. 2 inthe lefthole(isolated).
•Subsequently,use a DMM totest whether the video socket is isolated.
Fig. 1 Fig. 2
Fig. 3
Disconnect the SIREMOBIL Compact from power
prior to beginning the work.
140
80
20
Remote release socket
Video socket
Threaded bolt
Videoin
Out1
Out2
Out3
OTV
X2
a
d
s
12
3
CAUTION

SIREMOBIL Compact Register 3 RXR2-130.033.02 Page 4 of 8 Siemens AG
Rev. 02 03.97 TD SP 1 Medical Engineering
4 Connecting laser camera
Remote release socket 1
without multi-format camera / without video printer 1
•Connectthe control cable at the MEMOSKOP"Printer"connector.
•Cut offthe 3.5 mm socket plug.
•Removetheinsulationfrom the ends ofthewires.
•Extendthecableusingthe 2-conductorcable includedwiththe shipment.
•Insulatethe location of the new connections with shrinktubing.
•Routetheendsof the wires throughthe holedrilledfor the remote release socket.
•Solderthewirestotheremotereleasesocket(referto 1/Fig.3and2/Fig.3).
•Solderoneendof the protectiveconductorincludedwiththeshipmenttothe remote
releasesocket(3/Fig.3)and connectthe otherend to the protective conductorterminal
screw(1/Fig.2).
•Installtheremotereleasesocket.
When a multi-format camera is present 1
•Cut offthe 3.5 mm socket plug ofthe existingcontrol cable.
•Removetheinsulationfrom the ends ofthewires.
•Extendthecableusingthe 2-conductorcable includedwiththe shipment.
•Insulatethe location of the new connections using shrink tubing.
•Routetheendsof the wires throughthe holedrilledfor the remote release socket.
•Solderthewirestotheremotereleasesocket(referto 1/Fig.3and2/Fig.3).
•Installtheremotereleasesocket.
When a video printer is present 1
•Cut offthe remote control connectorfor the multi-format camera of the existing control
cable.
•Removetheinsulationfrom the ends ofthewires (greenandwhite wires).
•Extendthegreenandwhitecableusingthe2-conductorcableincluded with the
shipment.
•Insulatethe location of the new connections using shrink tubing.
•Routetheendsof the wires throughthe holedrilledfor the remote release socket.
•Solderthewirestotheremotereleasesocket(referto 1/Fig.3and2/Fig.3).
•Installtheremotereleasesocket.

Connecting laser camera 5
Siemens AG Register 3 RXR2-130.033.02 Page 5 of 8 SIREMOBIL Compact
Medical Engineering Rev. 02 03.97 TD SP 1
Power cable 1
•Connectthe power cable ofthevideoseparatordevice at terminalsX2.1and X2.2
(Fig.1).
•Connectthe protectiveconductorto the protectiveconductorterminalstrip(yellow/
green)(Fig.1).
•Routethepowercabletothe video separator deviceand connectit.
Video cables 1
When a multi-format camera or video printer is present 1
•Disconnectthe 75 Ohm terminating resistorfrom the video output of themulti-format
camera ordisconnect theswitchable 75Ohm termination ofthe video printer.
•Connectthe video cable tothe video output of the multi-formatcameraor the video
printer, routeit to thevideoinputofthe opticalvideo separatordevice,andconnectit.
•Routethesecondvideocablefrom the outputof the opticalvideoseparatordevice to the
insulated, built-in video socketand connect it.
Without a multi-format camera or video printer 1
•Connectthe video cable atthe MEMOSKOP "Out3" connector.
•Routethevideocabletothevideoinputofthe opticalvideoseparatordevice.
•Routethesecondvideocablefrom the outputof the opticalvideoseparatordevice to the
insulated, built-in video socketand connect it.
When a video recorder is present 1
•Disconnectthe 75-Ohm terminatingresistorof the video recorder.
•Connectthe video cabletothe video recorderoutputand routeit to the video inputof the
opticalvideo separatordevice.
•Routethesecondvideocablefrom the outputof the opticalvideoseparatordevice tothe
insulated, built-invideo socketand connect it.