MedaCure LX-BARI User manual

USER MANUAL
FOR
SERIES MODEL # LX-BARI & LX-BARI-9
© 2021
MADE IN CHINA
IMPORTANT:
CHECK THE LABEL ON THE BED FRAME FOR THE CORRESPONDING MODEL NUMBER

1 | Page
TABLE OF CONTENTS
PAGE 2
PAGE 3
PAGE 4
PAGE5
PAGE 6-8
PAGE 8
PAGE 9
PAGE 9-10
PAGE 10
PAGE11
PAGE11-12
PAGE13
PAGE 13
INRODUCTION P& RODUCT FEATURES
PARTS LIST AND DESCRIPTION
INSTALLLING THE LIFTING FRAME
&HEIGHT ADJUSTMENT MOTOR
INSTALLING THELENGTH EXTENSION FRAME
INSTALLING BED BOARDS
WIRING THE NURSE CONTROL
CASTERS
BED WIDTH EXTENSION
BED LENGTH EXTENSION
CORNER MATTRESS RETAINER
BUMPER GUARD INSTALLATION AND USAGE
PATIEN RT EMOTE HANDSET
TRENDELENBURG
TRAPEZE AND IV POLE SOCKETS
PAGE 13

2 | Page
The MedaCure Lincoln Expandable Bed is a fully electric, versatile and multi-functional bed for Long Term Care,
Hospital & Homecare settings. It expands in both the width (from 36” to 48”) and length (from 80” to 88”) which makes it
ideal for standard, bariatric and tall patients. The LX-BARI has a low position of 14.9” and 5 patient position functions to
enhance the quality of care and for ultimate comfort. The LX-BARI uses 4 sophisticated motors to control all functions and
has a weight capacity of 700 lbs. The bed comes standard with a patient remote handset. The bed is a Class II Medical
Device. The plug and the motors are IP43 rated.
Durable and built to last with all steel construction and removable head & foot boards. The LX-BARI is a sturdy bed with
multi-functional features and an attractive upscale design that will enhance the décor of any room.
10 Function Electric Bed
Head and Foot, Hi/Lo, Trendelenburg & Reverse Trendelenburg
Expandable width from 36” – 42” – 48”
Adjusts for both Standard and Bariatric Patients
Patient remote handset for all 5 positions
Hi position to 30” (LX-BARI) and 25" (LX-BARI-9)
Low position to 14” (LX-BARI) and 9" (LX-BARI-9)
Expandable width from 36" 42" - 48"
Expandable length from 80” to 88”
8 Casters: 4 pcs. swivel & 4 locking casters
Under bed clearance of 5.7”
IV pole mount on 2 head corners and the middle of the bed frame
Trapeze bracket mount on 2 head corners
Durable rectangle tube bed deck
Interchangeable head/foot boards
Durable 1 piece reinforced steel frame
Each bed has four mattress retainers, 1 on each corner
Each bed has two bumper guards on the head of the bed
Foldable head board
Weight capacity: 700 lbs.
Width Expands & Retracts
without any Tools
10 Position hand pendant
with Trendelenburg Function
Heavy duty rectangle
tube bed deck with
reinforced steel frame
Tool-less Design -
Width & Length expand
& retract without tools
8 - 3” Durable Casters:
4 Swivel and
4 Locking Casters
PRODUCT FEATURES

3 | Page
PARTS LIST & DESCRIPTION
IMPORTANT: Read this manual completely before setting up or operating this system and
keep in a safe place for future reference. To avoid injury and for maximum safety, this
system should only be installed by an authorized technician or dealer representative.
Electric bed installation parts listed below as per Figure # 1
Figure # 1
Bed frame
Bed foot board (with
optional nurse control）
Bed head board
M8 × 20 Cup head
bolt
M8 ×18 Plate nut
Bracket for bed foot part
Extension frame (left)
Extension frame (right)
Φ8 Flat washer

4 | Page
1. Installing the lifting frame
Remove theφ13.5 bolt from the lifting frame (1). Place aφ14 plastic washer between the lifting
frame (1) and lifting frame (2), matching the bolt holes on both lifting frames. Fasten with a φ
13.5 bolt with cotter pin as per Figure # 2. Use 4 bolts to connect the lifting frames.
Figure # 2
2. Installing height adjustment motor
Match the installation holes on height adjustment motor and motor base and fasten byφ10
bolt with latch as per Figure # 3. Before attaching the bolt, first attach a 10 plastic washer to the
bolt. Install the two height adjustment motors one by one.
Figure # 3
φ14 Plastic
washer
φ13.5 Bolt

5 | Page
3. Installing the length extension frame
3.1. Insert extension frame (left) & extension frame (right) into the 60 x 30 mm rectangular bed
frame tube. See Figure # 4
Figure # 4
3.2. Install bracket for bed foot part as per Figure # 5.
`
Figure # 5
The extension frame tubes
should face upward.
Insert the extension frame, tighten the
bolt to lock the extension frame, and
then fix the plastic head bolt.

6 | Page
4. Installing the bed boards
4.1 Press the M8 × 18 plate nut into the bed board holes, as per Figure # 6.
Figure # 6
4.2.1 Match the bed head board with the bed frame installation holes. Fasten by M8 X 20 cup
head bolt with φ8 flat washer, as per Figure # 7.
Figure # 7
4.2.2 Foldable head board installation as noted in Figure # 7.1

7 | Page
UnfoldedPosition
FoldedPosition
Figure # 7.1
4.3 Match the bed foot board with the extension frame installation holes.
Fasten by M8 X 20 cup head bolt with φ8 flat washer.
Bed foot board can be installed in both the high and low level position. See Figure # 8 & Figure # 9.
Figure # 8 Bed foot board in low-level installation position

8 | Page
Figure # 9 Bed foot board in high-level installation position
4.4 Install the bed head board to the bed head frame, and bed foot board to the bed foot frame,
as per Figure # 10.
Figure # 10

9 | Page
5. Casters
There are 4 pcs. locking casters and 4 pcs. swivel casters per set.
Step on the locking pedal (lower) to activate the locking position and step on the unlocking pedal
(upper) to deactivate the locking system. See Figure # 12 & 13.
Figure # 12 Lockedposition Figure # 13 Unlocked position
6. Operation for bed surface extension frame
6.1 First, loosen the “Locking Bolt”. Then, pull the “Pulling Button” with one hand and pull out
the extension frame until it clicks into your desired location hole (see 6.2 below). Tighten the
“Locking Bolt” to lock the extension frame in place. See figure # 14.
Figure # 14
Step on the pedal to
unlock the caster
Step on the pedal to lock
the caster in
p
lace
Locking Bolt
Pulling Button

10 | Page
6.2 IMPORTANT NOTE: There are 3 location holes on each extension frame for 3 width
adjustment settings - 36”, 42” and 48” widths. There are 4 separate extension frames on each
side of the main frame. Repeat the above method in 6.1 to achieve the desired width and then
tighten the “Locking Bolt” to lock the extension frame in place. See Figure # 15.
Figure # 15
7. Bed foot length extension frame
Loosen the screw on the bed frame, and pull out the extension frame.
Tighten the screw until the ideal length is selected, as per Figure # 16.
Figure # 16
Screw

11 | Page
8. Each corner of the bed frame has two mattress retainer installation holes.
Insert the mattress retainer as noted in Figure # 16.1.
Mattress Retainer Installation for Standard Bed Deck   Mattress Retainer Installation forExpandable Bed Deck
Figure # 16.1
9. Bumper Guard Installation and Usage
There are two retractable rubber Bumper Guards on the head of the bed. When extended
they will protect the walls when raising or lowering the bed. Retract the bumper guards to
discreetly store under the frame.
9.1 Insert the bumper guard stem to the bracket. Align the mounting holes and fasten the
screws as noted in Figure # 16.2.
Figure # 16.2

12 | Page
9.2 Extended Position: Push the bumper guard stem upward and turn the stem outward until
the screw clicks with slot as noted in Figure # 16.3.
Figure # 16.3
9.3 Retracted Position: when bumper guard is not in use, push the stem upward and turn it
inwarduntilscrewclickswithslotasnotedinFigure#16.4
Figure # 16.4
10.Side Rails and Assist Bars
10.1. Medacure has multiple side rail and assist bar options. Please contact your dealer or authorized
representative for details.
For rail entrapment guidelines please visit the FDA.Gov website

13 | Page
11. Patient remote handset
Raise bed head part Lower bed head part
Raise bed foot part Lower bed foot part
Raise both bed head
and foot part
Lower both bed head
and foot part
Raise the entire bed Lower the entire bed
Trendelenburg Reverse Trendelenburg
Figure # 17 Trendelenburg position Figure # 17.1 Reverse trendelenburg position
11.Trapeze pole andIV pole sockets
There are two (2) trapeze pole socketsand two (2) IV pole sockets onthe head part of the
bed frame. The Trapeze IV poles are not included with the bed and should be purchased
separately.
© 2021
MADE IN CHINA