Mammoth Innovation Monkey Vision MOMETER PRO User manual

MOMETER
PRO
Mokey
TEMPERATURE SCANNINGFACIAL RECOGNITIONACCESS CONTROL
QUICK START GUIDE

INTRODUCTION
The Monkey MOMETER PRO has been specifically developed
to help Australians take the necessary health and safety precautions
as we get back to life post the initial Covid-19 lockdown.
With accurate, contactless temperature scanning and
the option of activating personal registration and access control,
it’s the perfect solution for offices, hotels, buildings,
schools, shops, cafés and restaurants, as our communities open up
to more patronage and use.
monkeyvision.com.au

NOTES:
1. Do not splash liquid or metal on the outer screen to avoid scratches or damage.
2. Clean with appropriate glass-cleaning solution to avoid watermark.
3. Take care when installing. Please handle the unit gently and don’t drop it. Surprisingly, it doesn’t handle that too well.
4. Please ensure that the equipment is well grounded to avoid interference and damage to the video and audio signals.
5. These instructions only relate to the use of the Monkey MOMETER PRO for temperature scanning.
6. Please don’t plug audio equipment, alarms and other external interfaces or terminals directly to the unit.
7. The Monkey Mometer Pro works best in room temperature between -10C and +55C and relative humidity
between 10%  90%. But if you’re working somewhere the room temperature is below 0C or above 30C
you should seriously consider looking for another job.
8. This product is for indoor use only. Not weather/waterproof.
monkeyvision.com.au

INSTALLATION TIPS
The Monkey MOMETER PRO’S primary function is to measure temperature. This means
it is sensitive to changes in temperature and humidity in its surrounding environment.
Ensure your unit it set up in a place with constant temperature, at least 3 metres away from
a direct heating or cooling source and not directly under a vent. When people enter a room
from the outdoors their temperature measurement accuracy will be affected especially
if you’ve come from a well-heated car, you’ve been out in the cold, or vice-versa.
For the most accurate result, please wait a minute or two for body temperature to regulate
before stepping up to the unit for temperature scanning. The temperature reading comes
from the forehead area. Rain/water on the forehead, sweat, oil, heavy makeup, and wrinkles
will cause the temperature reading to be lower than the actual temperature.
Please ensure the user’s face is clear with no hair or clothing covering the forehead area.
monkeyvision.com.au

TO BUILD YOUR STAND:
The upright posts have four holes
in each end. One of those ends
has hexagonal nuts on the inside.
That’s the bottom.
Attach the baseplate to one of the
posts using four of the supplied bolts.
Screw them in by hand then tighten
with a 10mm spanner or drill.
THE STAND HAS THREE MAIN PARTS: A BASEPLATE AND TWO UPRIGHT POSTS.
(YOU SHOULD ALSO HAVE A POWER CABLE, TWO BACK PLATES, A LARGE SPACER RING AND 20 BOLTS)
Carefully place the other post
on top and attach the bolts.
STEP 1 STEP 2 STEP 3
monkeyvision.com.au

TO ATTACH YOUR MONKEY MOMETER PRO:
Loosen the large nut at
the bottom of the
Mokey MOMETER PRO
and remove it.
Feed the cords through
the hole at the top of
your stand one at a time
until all are through.
Tighten the nut as much as
you can by hand. If you like,
you can tighten further with
a large adjustable wrench. Feed the power cable
through the bottom mail slot on
one of the back plates.
Then feed the cable up
though hole between the posts
and connect it to the
Mokey MOMETER PRO’S
power cable.
Feed the chords through
the spacer ring and large nut.
STEP 1 STEP 2 STEP 3 STEP 4
Affix the two back plates
using your remaining bolts.
STEP 5 STEP 6
monkeyvision.com.au

TO START USING:
Place the stand….
Plug the plug into
a standard wall socket.
If you use an
extension lead, ensure
it is taped down so
no one trips over it.
Place the floor decal
50cm away from
the front of the stand.
The Mokey
MOMETER PRO will
power up within 10 seconds
of being plugged in.
For best results wait a few
minutes before using.
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
You’re good to go!
The Mokey MOMETER PRO will tell you if something is wrong – like if you need to stand closer to or further away
from the unit, or if you need to clear things away from your forehead for a more precise temperature measurement.
STEP 6
monkeyvision.com.au

CONNECTOR INTERFACE INTRODUCTION
monkeyvision.com.au
12
3
45
6
7
A+
B-
C
D
12
3
45
6
7
A+
B-
C
D
1. USB 5V DM DP GND
2. Access Control (output)
Aand BNormal open, default normal open,
identification passed-connection, (alarm output 2)
Cand DNormal close, default normal close,
identification passed-disconnection, (alarm output 2)
3. Reset Key Hard reset
4. Power Connector DC 12V
5. Alarm Output GND+ALMO alarm output 1, without action output
3.3V, with action output 0V
6. Wiegand Connector -WGI0 +WGI1 (input)
7. RJ45 100M

Level 1, 527 Chapel Street, South Yarra. Vic. Australia 3141
For terms and conditions, and to order online visit
monkeyvision.com.au
This guide has been put together by combining a translation of the manufacturer’s original instructions with our own practical use and testing.
The information contained within this document provides the user with all the practical information required to safely set-up and operate the
Mokey MOMETER PRO as a temperature scanning device only. Without written permission, no unit or individual may in any way extract, copy,
translate or modify all or part of this manual. Except as otherwise agreed, we do not make any representations or warranties, express or implied.
BLAINE COATES
[e-mail]
0409 099 819
For all trade and bulk enquiries contact:
EASY TO ORDER ONLINE WITH 30 DAY MONEY-BACK GUARANTEE
JASON BIDDELL
[e-mail]
0404 030 366
oror
ASH ISRAEL
[e-mail]
0400 978 877