MANGA STREET SCOOPI SEAT User manual

Table of Contents
Layout
Dimensions and description
Mounting Scoopi with bracket or lling it with sand
Joining multiple Scoopis
Mounting Scoopi Button in PE plastic
Assembly of Scoopi Table for 2 Scoopis
SCOOP/Scoopi assembly
Scoopi & SCOOP care
Mounting Scoopi Button & Table Top in EPDM rubber
1
2
3-4
5-6
7
8
9
9
10
PI
SEAT

SCOOP
SCOoPI
SCOoPI BUTTON
SCOoPI TABLE
SCOoPI TABLE TOP
LAYOUT
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
1-9
PI
SEAT

DIMENSIONS & DESCRIPTION
PI
SEAT
FROM THE SIDE
REAR VIEW
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
SCOoPI SEAT &
SCOoPI BUTTON
SCOoPI SEAT &
SCOoPI TABLE TOP
SCOoPI TABLE TOPSCOoPI TABLE
SCOoPI TABLE
1492 cm/
587.4 in
54 cm/
21.3 in
73 cm/
28.7 in
37 cm/
14.6 in
64 cm/
25.2 in
35 cm/ 13.8 in
18,5 cm/
7.3 in
40 cm/
15.8 in
37,5 cm/
14.8 in
36 cm/
14.2 in
SCOoPI BUTTON
65,5 cm/
25.8 in
40 cm/
15,8 in
CAVITY
PERSPECTIVE
FRONT VIEW
2-9
SCOoPI BUTTON IN PLASTIC SCOoPI BUTTON IN RUBBER
BRACKET FOR PLASTIC BUTTON
BRACKET FOR RUBBER BUTTON

Place the Scoopi bracket like shown in no 2. Fasten with washers and
bolts so it is quite rm. Mount brackets on all Scoopis in the layout.
For inspiration see page 1.
FILLED with SAND or MOUNTED to the ground?
BRACKET for
PE plastic button
(See page 10 for bracket for EPDM rubber
button and EPDM table.)
ASSEMPLY
1
3
2
4Place the Scoopi in the desired lay-
out. Here is a layout with 6 Scoop-
is. Mark in holes of the bracket.
Remove Scoopi. Drill holes in the
ground. Place Scoopi again and
mount one at a time to the ground
with expansion bolts or what is
suitable for a hard surface.
Place large plug in the hole
inside Scoopi. Mount Scoopi
Button like shown on page 7.
3-9
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
PI
SEAT
MOUNTED to the ground - hard surface - outside:
2 x BOLTS
M 10 mm x 20 mm
2 x WASHER
2 x SPRING WASHER
Manga Street does not guarantee
against theft or vandalism.

FILLED with SAND:
INDOORS: Fit base levellers/felt shoes
on the bottom in the 3 bushings to avoid
scratches on the oor.
OUTDOORS: No base levellers.
ASSEMBLY
1
4
4-9
3
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
Manga Street does not guarantee
against theft or vandalism.
PI
SEAT
2
PLACED: Place the Scoopis in the
desired layout. See page 1 for inspi-
ration. Here is a layout with 4 Scoop-
is and a Scoopi table. For mounting
Scoopi Table see page 8.
For joining Scoopis to each other
see page 5-6.
When rubber button is delivered: Mount bracket before pouring in sand;
for guidance see page 10 (Wait with rubber button). Pour kiln-dried sand
in through the big hole inside Scoopi. Insert the large plug in the hole so
that it ts tightly. (If the sand is to be emptied out later, there is a plug in
the bottom of the Scoopi.)
Mount Scoopi Button: In Plastic see page 7. In rubber see page 10.
PLACED or JOINED to each
other?
SCOoPI TABLE
100 kg/
220 lbs
125 kg/
275 lbs
SAND

a
JOINING multiple Scoopis:
Drill two holes with a 22 mm drill bit in the front of the Scoopi as shown
in the drawing below.
Drill on the 2 marked spots with a 22 mm drill bit.
If xing with bracket - mount bracket now, in each
Scoopi. See page 3.
JOINING
1
22 mm
bb
a
3
4
a
2Place the Scoopi in the desired
layout.
See page 1 for inspiration.
Here is a layout with 6 Scoopis.
Through the large hole in the centre of Scoopi band out through both
the front drilled holes, mark on the side of Scoopi a with a permanent
marker. If there are more Scoopis in the layout, pre-drill (no 1) and mark
them all in the same way. It is an advantage marking out on a at surface.
a
b
c
5-9
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
SCOoPI´s with sand and joined.
PI
SEAT
Manga Street does not guarantee
against theft or vandalism.

Place a washer and nut loosely on joining bracket’s threaded rod.
Insert the joining bracket in the 22 mm hole and make sure that it goes
through and opens on the inside of Scoopi a. Screw the threaded rod in
so about ca 45-50 mm (1,77 in) is protruding. Screw the washer and nut
tight. Repeat for second hole. For indoor use mount felt shoes like shown
on page 4 no 1 and return to this page afterwards.
Place Scoopi a and b close together so the two linking brackets go through the
two pre-drilled holes on Scoopi b. Fit the washer and nut on both joining brack-
ets through the large hole in Scoopi band tighten it so that the two Scoopis are
securely attached together. Repeat on the other Scoopis in the layout. See page 4
for lling in sand and mounting the large plug. For mounting Scoopi Button, see
page 7.
JOINING
5
6
a
a
a
45 mm thread
1,77 in thread
2 x JOINING BRACKETS
M 8 mm
20 mm
4 x WASHERS 40 mm
4 x NUTS M 8 mm
a b
a + b
6-9
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
PI
SEAT
Manga Street does not guarantee
against theft or vandalism.
SCOoPI´s with sand and joined.

MOUNTING- SCOoPI button
Fasten the two accompanying bolts in the upper bushes.
Place MARK in the bottom of Scoopi Button towards the
cavity of Scoopi Seat like shown here on the right. Attach
the Scoopi Button to the Scoopi Seat by pressing the two
holes in Scoopi Button over the screws until it clicks. Take
care of ngers when doing this. Use for instance body
weight. If it doesn´t click on rmly turn the button opposite.
1
2 x BOLTS M 10 mm
x 50 mm
7-9
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
SCOoPI BUTTON
SCOoPI BUTTON
UNTIL IT CLICKS
PI
SEAT
This is WRONG
This is RIGHT
MARK

TABLE
PI
Manga Street does not guarantee
against theft or vandalism.
ba
Position both Scoopi brackets and mount them as shown on page 3.
Insert the Scoopi Table’s threaded rods into the pre-drilled holes and
mount with the 16 mm nuts supplied through the large hole on the inside
of the Scoopi in both a and b.
Drill with an 18 mm drill bit in the two holes in the front of the Scoopi as
shown in the drawing below on both a and b.
1
2
Place the Scoopi/Scoopis in the desired layout, where the two
Scoopis a + b are tted with a Scoopi Table.
See pages 3-4 for xing it to a rm surface or lling it with sand and
how to mount the large plug.
See pages 7 and 10 for mounting the Scoopi Button.
a + b
3
b
acd
4 x NUTS M 16 mm
18 mm
8-9
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
MOUNTING - SCOoPI Table

Manga Street does not guarantee
against theft or vandalism.
Scoop & Scoopi and Scoopi Button in plastic, require very little maintenance.
If necessary, clean them with soap and water or/and with “rubber and plastic
cleaner” on any blemishes. They can easily be cleaned with a pressure washer.
Scoopi Button made from rubber, as well as Scoopi Table and Scoopi Table
Top, also in rubber, are water permeable and durable. Rubber products can be
cleaned and the colours can be freshened up with a shampoo that is suitable
for cleaning rubber.
Rubber products can be cleaned with a pressure washer, but carefully and with
less pressure so the surface is not damaged or becomes frayed. Chewing gum
can often be removed using the above method, or you can also use a freeze
spray. Then remove it mechanically. If lights are tted in Scoop Light, the light
chain, etc., must not be cleaned with water. See Scoop assembly instructions
for cleaning and mounting this.
Important: Plug in the bottom of Scoop: Remove before permanently
xing the Scoop in position. To mount the Scoop, see its instructions.
Scoop & Scoopi Seat are not attached together. But placed quite
close together. If you choose to x them in a permanent position,
use the F2 brackets for Scoop and one of the two variations of
brackets for Scoopi.
You can also pour sand in the Scoopi instead see both variations on
page 3-4.
NOTE! The Scoopi Button in rubber must always be mounted on
the bracket’s threaded rod regardless of whether the Scoopi stands
outside or inside/is xed in a permanent position or not.
9-10
SCOoPI & SCOOP CARE
SCOoPI BRACKET
for PE plastic button
SCOoPI with SAND
SCOOP & SCOoPI
F2 SCOOP BRACKET
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
PI
SEAT

Manga Street does not guarantee
against theft or vandalism. 10-10
MANGA STREET APS
Web: www.mangastreet.eu
Mail:[e-mail]
PI
SEAT
The Scoopi Button & Table Top in EPDM rubber is mounted in the ex-
act same method. Regardless of whether the Scoopi is to be inside or
outside the bracket is always to be mounted and attached to the but-
ton or the table. Follow the steps from 1-4. To fasten the Scoopi Table
Top or the Scoopi Button, screw directly into the rubber and into the
Scoopi like shown on the right, so the head of the screw disappears
into the rubber or give the upper part of the threaded rod a blob of
Loctite adhesive. Screw the Scoopi Button/Scoopi Table Top onto the
threaded rod until it is rmly against the inside of the Scoopi.
NOTE: Afterwards, it will not be possible to separate the two parts, or
it will be very dicult, but they can be separated mechanically.
LAST! No 4: Screw the
Scoopi Button or the Table
Top onto the threaded rod
until rm and fasten with
glazing bead screws.
The Scoopi Button or
the Scoopi Table Top is
fastened with glazing
bead screws in the places
shown, so they disappear
in the rubber and grip the
inside of the Scoopi Seat.
Else use a few drops of
Loctite glue on the top of
the treaded rod and turn
Scoopi Button on rmly.
4
No 1: BRACKET - Put the
Scoopi bracket in place.
NOTE: The threaded rod
should be angled forward
towards the cavity as
shown on the left side.
1
FORWARD
BRACKET side
SCOoPI BRACKET No 2: The bolts with wash-
ers are screwed into the
lower bushings Through
holes in the sides of the
bracket until rm.
For detail see page 3.
No 3: Fasten Scoopi Seat.
For suggestions see page
3.
2
3
SCOoPI BUTTON in EPDM
SCOoPI TABLE TOP
MOUNTING - TABLE TOP
OR BUTTON IN EPDM
For picture of Scoopi Button in EPDM rubber
mounted on Scoopi Seat see following page.

Natskyggevej 30
3390 Hundested
Denmark
P : [phone]
VAT No : DK 38350668
MANGA STREET APS
Web:www.mangastreet.eu
Mail:[e-mail]
Photos :Anna-Lene Riber