MANN LAKE HH-200 User manual

6/3 Frame Motorized
EXTRACTOR
HH-200
Rev: 10/01/19
501 1st St S, Hackensack, MN 56452
500 Santa Anita Dr., Woodland, CA 95776
485 Stewart Rd, Wilkes-Barre, PA 18706
1600 Commerce Street, Marshall, TX 75672
Telephone: [phone]
www.mannlakeltd.com

Congratulaons on purchasing your new extractor. Shown below are just
a few things you need to do before you begin extracng. If you have any
quesons at all, please feel free to call your nearest Mann Lake locaon.
Experienced help is only a phone call away.
Aach the legs to the top of the extractor can with the nuts that are provid-
ed and ghten with an adjustable wrench. Lay the extractor on its side and
aach the leg support to each of the legs with the nuts that are provided.
The “feet” of the extractor legs have a hole that can be used to mount the
extractor. We suggest mounng to a 4’ x 4’ (121.92 cm x 121.92 cm) piece
of plywood for stability. The nal step is to aach the lid. On the rear side
of the extractor, insert one side of the plasc cover into the open poron
of the hinge located on the crossbar. Slide the lid into the closed poron of
the hinge to secure. Repeat with the front lid. You also need to install the
Safety Stop on the front right hand side of the lid. Place the Safety Stop on
the threaded bolt as shown. Place the threaded nut over the Safety Stop
and ghten with a 1/2” or 13mm socket. Note: if you would like to remove
the lid in the future, the Safety Stop will need to be removed. Installaon
of the Safety Stop is necessary to keep the lid from becoming dislodged
during extracng. Do not operate your extractor without the Safety Stop
in place. Now you are ready to begin extracng.
The basket is supported by allen screws located along the shaft at the top
and bottom of the basket. Be sure to tighten these screws prior to using.
If at any time the shaft spins but the basket does not, you will need to
tighten them again.
Frames should be uncapped prior to extracng. The load inside the extrac-
tor must be balanced in order for the basket to spin properly. The motor
on your new extractor is a variable speed motor. When using 9 1/8” (23.18 cm) or 6 1/4” (15.8 cm) frames with
wax foundaon, we recommend pung the speed control on 20. Run the extractor for 2-3 minutes each on “20,”
“50,” and for 4-5 minutes on “90.” At the end of that me, move the switch to “0,” wait for the basket to stop, and
ip your frames. Extract side 2 in the same fashion for 3 minutes on each seng. If necessary, repeat the process
again on side 1 to remove the last of the honey. Rotang the frame will lessen the occurrence of blowouts in the
wax foundaon from the weight of the honey.
If plasc foundaon is used, it is possible to extract each side 100%
before turning. Run for 5 minutes each on “20,” “50,” and “80,” then
switch to the “90-100” for an addional 10-15 minutes before ipping
your frames.
5⅜” (13.67 cm) frames are placed radially as shown on the opposite
page. It is not necessary to turn frames placed radially. Run for 5 min-
utes each with the dial on “20,” “50,” and “80,” then switch to the “90-
100” for an addional 10-15 minutes.
Keep your honey gate open when extracng to ensure the basket moves
freely. Your extractor is not intended to be a storage tank. Promptly move any honey to a storage container or
boling tank.

One Year Limited Warranty: Mann Lake warrants this product, to original purchaser, for one year from purchase date to
be free of defects in materials and workmanship. This warranty is the only written or express warranty given by Mann Lake
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS ARE HEREBY EXCLUDED. Mann Lake’s obligation under
this warranty is limited to repair or replacement of the product, at its option. IN NO CASE SHALL MANN LAKE BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM BREACH OF THIS WARRANTY.
Part # Description Quantity √
81-833 Motor Mount for 6/3 Motor with Guard 1
81-733 6/3 Motor with Speed Control 1
80-000 Small Mann Lake Label 1
81-933 1/2” Coupling 1
Lid With**Cauon Label ** 1
80-001 Large Oval Mann Lake Label 1
36-122 3 mm Allen Wrench 1
36-115 Retainer Hinge (Safety Clip) 1
Instrucon Sheet 1
Inspected By:
6/3 Motorized Extractor
PARTS LIST
Frame Placement
Holds 3 - 9⅛”
(23.18 cm) Frames
Holds 3 - 6¼”
(15.88 cm) Frames
Holds 6 - 5⅜”
(13.67 cm) Frames

Wash all equipment before use. To clean your extractor, use warm to hot water with a so cloth. Please do not use
anything rough and abrasive on extractor. If the extractor is sll not clean you may use a small amount of dish soap.
There is no need to disassemble the extractor while cleaning it. If you feel the need to disassemble the extractor,
please be aware of the small ball bearing where the sha meets the boom of the extractor.
Boom of Barrel
(inside) Ball Bearing
The Sha sits on Ball
You May Also Be Interested In:
HH-231 Plasc Uncapping Tank
5 gal. pail with honey gate
Hourglass Embossed Plasc Jars