Marantz VP-10S1 User manual

Partner: Marantz
Model: VP-12S3 + VP-10S1
Device Type: Display
GENERAL INFORMATION
SIMPLWINDOWS NAME: Marantz VP-12S3 + VP-10S1 Projector.umc
CATEGORY: Display
VERSION: 1.0
SUMMARY: This module will control the following functions of the VP-12S3 + VP-10S1 DLP
Projectors: Power, Source Select, Picture Mute, Lamp Mode, Aspect Ratio, full menu
control, presets and display Elapsed Lamp Hours.
GENERAL NOTES: This module will control the Marantz VP12-S3 + VP-10S1 DLP Projectors. True
feedback is provided for all functions including elapsed lamp hours. When any
command is sent to the projector, it will acknowledge that the command was
processed properly and the corresponding feedback will be reflected at the outputs
of this module.
When the Poll_Enable input is asserted (Default =1), the projector will be polled
every 15 seconds to determine the state of power. If it is desired to poll the
projector for all other setting changes made using the IR remote control, or by the
controls on the projector itself, you can assert the Poll_Settings input (Default =1).
When this input is high, the projector will be polled every 45 seconds to determine
the state of current selected source, aspect ratio, picture mute lamp mode, presets
and elapsed Lamp Hour usage. Typically, you could enable either polling option
when the projector's particular control page is active and displayed on a touch
panel. You would then disable polling at other times.
CRESTRON HARDWARE REQUIRED: C2-COM, ST-COM, CNMSX Internal Com Ports
SETUP OF CRESTRON HARDWARE: RS232
Baud: 9600
Parity: N
Data Bits: 8
Stop Bits: 1
RTS/CTS Handshaking Enabled
VENDOR FIRMWARE: None
VENDOR SETUP: None
CABLE DIAGRAM: CNSP-143

Partner: Marantz
Model: VP-12S3 + VP-10S1
Device Type: Display
CONTROL:
Power_On/Off/Toggle D Pulse to turn the projector on and off.
Input_* D Pulse to select the input.
Picture_Mute_* D Pulse to turn the picture mute on and off.
Aspect_* D Pulse to select the aspect ratio.
Lamp_Mode_* D Pulse to select the lamp mode.
Preset_* D Pulse to select the preset. The VP-10S1 does not have the following presets:
User_B_1, User_B_2, User_B_3, User_C_1, User_C_2, User_C_3
Menu_* D Pulse to turn the menu on and off.
Poll_Enable D When high, device is polled every 15 seconds for its power status.
Poll_Settings D When high, device is polled every 45 seconds for current settings.
From_Device$ S Serial signal to be connected from a 2-way serial com port.

Partner: Marantz
Model: VP-12S3 + VP-10S1
Device Type: Display
FEEDBACK:
Power_*_Fb D High to indicate the current power state of the projector.
Input_*_Fb D High to indicate the currently selected input.
Aspect_*_Fb D High to indicate the currently selected aspect ratio.
Picture_Mute_*_Fb D High to indicate the current picture mute state of the projector.
Lamp_Mode_*_Fb D High to indicate the current lamp mode of the projector.
Preset_*_Fb D High to indicate the currently selected preset.
Status_*_Fb D High to indicate the projector’s current status.
Lamp_Hours A Current lamp hours.
To_Device$ S Serial signal to be routed to a 2-way serial com port.
TESTING:
OPS USED FOR TESTING: PRO2: 3.137
CNMSX: 5.14.02X
COMPILER USED FOR TESTING: 2.05.22
SAMPLE PROGRAM: Marantz VP-12S3 + VP-10S1 DLP Projector Demo
REVISION HISTORY: V. 1.0