Marchetti CLASS02 User manual

STOOLS
European norm EN 14183
D.Lgs 09.04.2008 n°81
www.marchetti.eu
The products identied in this handbook have been manu-
factured by MARCHETTI s.r.l. With QUALITY SYSTEM MANA-
GEMENT, certied by Tuv Italia, in accordance with ISO 9001
Handbook written in conformity to EN 131 norm part 3
and EN 14183 norm (stools).
Stools must be used only for nishing, maintenance
or similar work. This handbook contains important
information regarding the use, maintenance and safety
of stools; the operator must have complete knowledge of
the information contained herein before use. Scrupulous
observance of this manual ensures that the work will be
carried out in accordance with worker’s health and safety
regulation D.Lgs.09.04.2008 n°81.
11212
DOC. CUSTOMER ASSISTANCE N. 137 REV. 0 DEL 08/05/2018
COPYRIGHT
This documentation is protected by copyright. Any copying
or reproduction, including extracts thereof,and the repro-
duction of images(even in a modied state),in only permit-
ted with the written authorisation of the manufacturer.

32
IT
www.marchetti.eu
D.Lgs.206/2005
AR T. 2- consumator i
Legend Table pictograms
Rungs/steps N.
Platform Height
Width
Overall dimensions
Max Height close
Volume mcWeight
Kg
Total load permitted
D.Lgs.81/2008
ART .113
Product made in
accordance with the in
force Italian Legislative
Decree 09 April 2008 n.
81 “TESTO UNICO SULLA
SICUREZZA”, Art.113
“portable ladders”
Product made in
accordance with
the in force Italian
Legislative Decree
06 September 2005
n. 206 “codice del
consumo”, Art. 2
ATTENTION:
• Read and understand this manual in its
entirety.
• Follow the instructions as indicated.
• Before any installation, verify the integrity of
each individual component.
!
Tested and certicated
product in accordance
with European law EN
14183
EN 14183
TABLE OF CONTENTS
Legend - Table Pictograms pag. 3
1. REGULATION REFERENCES pag. 4
2. DECLARATION OF CONFORMITY pag. 4
3. ASSEMBLY INSTRUCTIONS pag. 5
4.1 Class - Class Più pag. 5
4.2 Sansone pag. 5
4. USER’S INSTRUCTION BEFORE USE pag. 5
5. REPAIR - MAINTENANCE pag. 5
6. WARRANTY pag. 5
7. USING THE STOOL pag. 6
8. STOOLS
Class pag. 7
Class Più pag. 7
Golia pag. 8
Sansone pag. 8
CHECK - LIST pag. 9
CHECK - LIST pag. 10
CHECK - LIST pag. 11

54
IT
www.marchetti.eu
1. REGULATION REFERENCES
• D.Lgs. 09.04.2008 n° 81 (G.U. n° 101 del 30.04.08)
“Testo unico sulla salute e sicurezza sul lavoro”.
• EN 14183 “Norma Europea Sgabelli”
• D.Lgs. 06.09.2005 n° 206 (G.U. n° 235 del 08.10.05 Suppl. Ordinario n° 162)
“Codice del Consumo”.
2. DECLARATION OF CONFORMITY
3. ASSEMBLY INSTRUCTIONS
3.1 Class - Class Più
• Place both hands at the center of the upper step and turn it up to the maximum of openness,
avoiding touching the uprights and lateral arms.
• Put all the 4 stool feet down and verify that all the feet are fully adherent a surface.
• If the parapet is present, rotate it from the position of 180 ° and until automatic inclusion of the
mechanical block. To return the parapet in the transport position, press with both hands, the
devices in the parapet.
3.2 Sansone
• After removing the packaging, enter the base into a black insert, located inside at the inferior
ends of the rst element’s uprights. Take the 2 bolts and the 2 provided wrenches in a bag at the
base of the ladder, embed the screws in their holes and tighten the nuts without forcing
• Put all the 4 stool feet down and verify that all the feet are fully adherent a surface.
• For closing up the lateral arm raise and then bring near the trunks in reverse movement to
opening.
4. USER’S INSTRUCTIONS BEFORE USE
Before using the stool for the rst time, make sure it is free from defects and complete with all its
elements. Give timely notice to the Supplier for any deciency.
5. REPAIR AND MAINTENANCE
- Only the manufacturer is allowed to make reparations, in order to avoid loss of certication of validity.
- Only use original components in case of replacement.
- Removal and recycling of the stool components: aluminum and steel for recycling, plastics parts remove from
the stool and collect for reconversion of waste material.
- Do not modify the ladder design.
6. WARRANTY
All MARCHETTI products are covered by the company’s ocial guarantee, pursuant to applicable
norms.
The guarantee is immediately eective and is ratied by the invoice accompanying the goods.
A product found to be faulty is guaranteed. We shall accept no responsibility for products used
incorrectly or damaged during use or transport. The product must be returned with its original
packaging, undamaged; it shall be covered by guarantee if it has not been dismantled, modied or
tampered with.
STOOLS
www.marchetti.eu
DECLARATION OF CONFORMITY
DECLARES
• That the products listed in the instruction handbook as pursuant
to D.Lgs. 09.04.2008 n°81 Art.113
• that the ladder- stools called: CLASS 02, CLASS 03, CLASSPiù 03,
CLASSPiù 04, SANSONE 03, SANSONE 04, GOLIA 02, GOLIA 03 are
constructed in Conformity with the Techical Norm EN 14183
• The tests were performed by:
UNIVERSITY OF PERUGIA
with headquarters in Città della Pieve (Pg) - Via Piemonte, 22:

76
IT
www.marchetti.eu
7. USING THE STOOL
CLASS Anodized aluminium ladders stool
COD. ART.
20519 CLASS02 2 0,8 0,46 0,50 490 4,50 0,03
20520 CLASS03 3 1,12 0,69 0,75 490 6,50 0,04
20521 CLASS04 4 1,43 0,92 1,00 490 8,00 0,05
CLASS Più Anodized aluminium ladders stool with parapet.
COD. ART.
20519 CLASS PIU 02 2 0,80 0,46 0,50 490 5,50 0,03
20523 CLASS PIU 03 3 1,12 0,69 0,75 490 7,90 0,04
20524 CLASS PIU 04 4 1,43 0,92 1,00 490 9,40 0,05
8. Stools
EN 14183
D.Lgs.81/2008
ART .113
D.Lgs.206/2005
AR T. 2- consumator i
Kg
Max 150
D.Lgs.
81/2008
ART.113
D.Lgs.
81/2008
ART.113
D.Lgs.
81/2008
ART.113
D.Lgs.
81/2008
ART.113
D.Lgs.
81/2008
ART.113
D.Lgs.
81/2008
ART.113
Warning, fall from the ladder. Maximum total load. (150 kg)
Refer to instruction manual/booklet. Maximum number of users.
Inspect the ladder after delivery. Before
every use visually check the ladder is
not damaged and is safe to use.Do not
use a damaged ladder.
Do not use the ladder on a unlevel or
unrm base.
Do not overreach. Do not wear unsuitable footwear when
climbing a ladder.
If a ladder is delivered with stabilizer bars
and these bars should be xed by the user
before the rst use this shall be described on
the ladder and in the user instruction.
Ladder for professional use.
Do not ascend or descend unless you
are facing the ladder. Do not use the ladder as a bridge.
Do not erect ladder on contaminated
ground.
Do not spend long periods on a ladder
without regular breaks (tiredness is a
risk).
Keep a secure grip on the ladder when
ascending and descending. Maintain a
handhold whilst working from a ladder
or take additional safety precautions if
you cannot.
Do not use the ladder outside in
adverse weather conditions, such as
strong wind.
Avoid work that imposes a sideways
load on ladders, such as side-on drilling
through solid materials.
Identify any electrical risks in the work area,
such as overhead lines or other exposed
electrical equipment and do not use the
ladder where electrical risks occur.
Do not carry equipment which is heavy
or dicult to handle while using a
ladder.
Do not move a ladder while standing
on it.
Open the ladder fully before use. Standing ladders shall not be used as a
leaning ladder unless it is designed to do so.
Do not step o the side of standing
ladder onto another surface.
Use the ladder with restraint devices
engaged only.
Open the ladder fully before use. Standing ladders shall not be used as a
leaning ladder unless it is designed to do so.
Do not step o the side of standing
ladder onto another surface.
Use the ladder with restraint devices
engaged only.
EN 14183
EN 14183
EN 14183
EN 14183
EN 14183
EN 14183

98
IT
www.marchetti.eu
SANSONE Aluminium stool
GOLIA Aluminium stool
COD. ART.
20704 SANSONE 3 3 0,90 0,73 0,72 800 8,50 0,12
20524 SANSONE 4 4 1,18 0,97 0,90 800 9,80 0,15
COD. ART.
20403 GOLIA 02 2 0,34 0,58 575 4,50 0,11
21450 GOLIA 03 3 0,49 0,80 632 5,50 0,13
A
Assembly instructions
BASE: Insert and x the base
as shown in gure A
CHECK LIST
Model of ladder_________ Revision of__________
² Make sure that the stiles don't have any bending, torsion, dent, crack, corrosion
or rotten parts.
² Make sure that the stiles are in good condition near the hinges.
² Make sure that the fastening means ( rivets, screws or bolts) aren't missing,
loosened or corroded.
² Make sure that the rungs/treads aren't missing, loosened or that they don't
present signs of wear, corrosion or damages.
² Make sure that the hinges connecting the frontal and back side of the ladder
aren't damaged or loosened and that they don't present signs of corrosion.
² Make sure that the fastening device remains horizontally positioned; the stiles
of the back side and the angular supports aren't missing, bended or loosened and
that they don't present sings of corrosion and damages.
² Make sure that the hooking devices to the rungs aren't missing, damaged,
loosened or corroded and that they correctly hook to the rungs.
Make sure that the sliding brackets aren't missing, damaged, loosened or corroded
and that they correctly hook to the stile.
² Make sure that the feet aren't missing, loosened and that they don't present
signs of wear, corrosion and damages.
² Make sure that the ladder is complete with all its parts without contaminant
agent such as dirt, mud, paint, oil and grease.
² Make sure that the fastening stops (if provided) aren't damaged or corroded and
that they correctly work.
² Make sure that the platform (if provided) isn't missing, corroded or damaged
parts or fastenings.
If one of the listed checks is not satisfactory, do not use the ladder for any reason
Encountered anomalies
Discarted items to be replaced
Observation
D.Lgs.
81/2008
ART.113
D.Lgs.
81/2008
ART.113
Open the ladder fully before use. Standing ladders shall not be used as a
leaning ladder unless it is designed to do so.
Do not step o the side of standing
ladder onto another surface.
Use the ladder with restraint devices
engaged only.
D.Lgs.
81/2008
ART.113
D.Lgs.
81/2008
ART.113
Open the ladder fully before use. Standing ladders shall not be used as a
leaning ladder unless it is designed to do so.
Do not step o the side of standing
ladder onto another surface.
Use the ladder with restraint devices
engaged only.
Health and Safety Manager
(Signature)
EN 14183
EN 14183
EN 14183
EN 14183

1110
IT
www.marchetti.eu
CHECK LIST
Model of ladder_________ Revision of__________
² Make sure that the stiles don't have any bending, torsion, dent, crack, corrosion
or rotten parts.
² Make sure that the stiles are in good condition near the hinges.
² Make sure that the fastening means ( rivets, screws or bolts) aren't missing,
loosened or corroded.
² Make sure that the rungs/treads aren't missing, loosened or that they don't
present signs of wear, corrosion or damages.
² Make sure that the hinges connecting the frontal and back side of the ladder
aren't damaged or loosened and that they don't present signs of corrosion.
² Make sure that the fastening device remains horizontally positioned; the stiles
of the back side and the angular supports aren't missing, bended or loosened and
that they don't present sings of corrosion and damages.
² Make sure that the hooking devices to the rungs aren't missing, damaged,
loosened or corroded and that they correctly hook to the rungs.
Make sure that the sliding brackets aren't missing, damaged, loosened or corroded
and that they correctly hook to the stile.
² Make sure that the feet aren't missing, loosened and that they don't present
signs of wear, corrosion and damages.
² Make sure that the ladder is complete with all its parts without contaminant
agent such as dirt, mud, paint, oil and grease.
² Make sure that the fastening stops (if provided) aren't damaged or corroded and
that they correctly work.
² Make sure that the platform (if provided) isn't missing, corroded or damaged
parts or fastenings.
If one of the listed checks is not satisfactory, do not use the ladder for any reason
Encountered anomalies
Discarted items to be replaced
Observation
CHECK LIST
Model of ladder_________ Revision of__________
² Make sure that the stiles don't have any bending, torsion, dent, crack, corrosion
or rotten parts.
² Make sure that the stiles are in good condition near the hinges.
² Make sure that the fastening means ( rivets, screws or bolts) aren't missing,
loosened or corroded.
² Make sure that the rungs/treads aren't missing, loosened or that they don't
present signs of wear, corrosion or damages.
² Make sure that the hinges connecting the frontal and back side of the ladder
aren't damaged or loosened and that they don't present signs of corrosion.
² Make sure that the fastening device remains horizontally positioned; the stiles
of the back side and the angular supports aren't missing, bended or loosened and
that they don't present sings of corrosion and damages.
² Make sure that the hooking devices to the rungs aren't missing, damaged,
loosened or corroded and that they correctly hook to the rungs.
Make sure that the sliding brackets aren't missing, damaged, loosened or corroded
and that they correctly hook to the stile.
² Make sure that the feet aren't missing, loosened and that they don't present
signs of wear, corrosion and damages.
² Make sure that the ladder is complete with all its parts without contaminant
agent such as dirt, mud, paint, oil and grease.
² Make sure that the fastening stops (if provided) aren't damaged or corroded and
that they correctly work.
² Make sure that the platform (if provided) isn't missing, corroded or damaged
parts or fastenings.
If one of the listed checks is not satisfactory, do not use the ladder for any reason
Encountered anomalies
Discarted items to be replaced
Observation
Health and Safety Manager
(Signature)
Health and Safety Manager
(Signature)

Via Piemonte, 22 - 06062 Città della Pieve - Perugia - Italy
Tel. + 39 0578 20348 - Fax + 39 0578 226488
[e-mail] - www.marchetti.eu
www.marchetti.eu