Marco MIX Font User manual

1
Instruction Manual: 1900105
Machine P/N: 1000943 , 1000879#, 1000879FB
1000941 & 1000942
MIX / POUR’D

2
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Contents
1.FontBox Contents................................................................................................2
2.CounterCut-Out.................................................................................................2
3.Installation..........................................................................................................4
No Drip Tray...............................................................................................4
Drip Tray...................................................................................................5
Connecting Hoses MIX...............................................................................6
Connecting hoses POUR’D..........................................................................8
4. Operating Font...................................................................................................7
5. Cleaning & Maintenance....................................................................................10
Counter Cut Out
• The 100mm /4” cut out is only required for the font with drip tray.
• The font without drip tray require the 32mm / 1 ¼” cut out only.
• Use a 32mm/ 1 ¼” & a 100mm /4” circular hole saw piece to make the holes.
3 & 1 Button Models
• 3 /1 button MIX Font 1000879 / 1000878
• Vent Hosing 1860388
• 8mm Water Hose 1860387
• 1/4” Water Hose 1860387
• Instruction Manual
• Vent plug 1401482
• 8mm-1/4” reducer 1400820
Font Box Contents
3B Concentrate 1000942
• 3B POUR’D concentrate Font
• 8mm Water Hose 2301250
• 1/4” Water Hose 2301251
• Vent Hosing 1860388
• Instruction Manual

3
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Counter Cut Out

4
Installation
32mm / 1 ¼”
1. No Drip Tray
130 - 500mm
130 - 500mm
50mm
Hosing should be trimmed to ensure
continuous drop from font to boiler

5
Installation
The drain outlet on the drip
tray should be plumbed to
waste.
32mm/ 1 ¼”
100mm/ 4”
2. Drip Tray (sold seperately p/n. 2300268)
130 - 500mm
130 - 500mm
50mm
Hosing should be trimmed to ensure
continuous drop from font to boiler

6
Cold Water
Hot Water Vent
Power
Connecting Hoses
MIX 3 Button Font Connections
MIX programmable buttons

7
Operating Font
1. Push & Hold
2. Push & Release
85°
100

8
POUR’D HOT/COLD WATER,
DILUTED CONCENTRATE & CONCENTRATE SHOT
3 button connections (1000942 3b concentrate)
IEC Power cable
Din connector to
boiler (If using chiller
go to page 7 of
Control box manual)
Soft tubing to Beverage
source
Hot water from
boiler 8mm tube
Mains or chiller water
(If using chiller go to page 7 of Control box
manual)
Cold water hard 1/4” tube
Beverage tube control box to
font
hard 1/4” tube
5/16 to 3/8
barbed
connector
if using chiller
put 3/4” to push fit elbow here
and connect to Chiller output
(if using chiller select ‘chiller
present’ in engineering setup
pg 10)
Din connector to font
(Plummed to mains
(If using chiller go to page 7 of Control
box manual)

9
POUR’D HOT/COLD WATER,
DILUTED CONCENTRATE & CONCENTRATE SHOT
3 button connections (1000942 3b concentrate)
Volumes must be calibrated, go to page 10
MODE DESCRIPTION
HOT Hot Water (set ratio to 0% )
COLD Cold / ambient water mixed with concentrate (set ratio
to 0% for just cold water)
RTD Ready to drink, undiluted concentrate
OFF Button non-active
PRI Triggers second control box, in case of 2 control boxes
primary must be one connected to the font
MODE
% CONCENTRATE (0% = just
water, 20%=4:1)
DISPENSE VOLUME
(P&H = push and hold)
3 nger press
short hold
% Concentrate Water to Coffee ratio
20% 4:1
10% 9:1
3 nger press
long hold
3 nger press
short hold
Set mode to UC MIX both
Control box setup
Boiler setup
.HOT
000%
P&H
Next
COLD
020%
200ml
RTD
--
30ml
--
.
Next - +
Factory preset
Mode: UC MIX BOTH
Temp units: ˚C
All temperatures the same
and volumes to 0
Off
Off
Descale weeks:
Filter Litres:
Set Pin:
Next - +
2.3.
UC MIX BOTH
°C
Factory preset
Mode:
Temp Units:
Next - +
6.
85°
183
5.
C
Factory preset
UC SINGLE°
Mode:
Temp Units:
Save - +
1.
DEFAULT
4.
UC SINGLE
°C
Factory preset
Mode:
Temp Units:
Next - +
Off
Off
Descale weeks:
Filter Litres:
Set Pin:
Next - +
2.3.
UC MIX BOTH
°C
Factory preset
Mode:
Temp Units:
Next - +
6.
85°
183
5.
C
Factory preset
UC SINGLE°
Mode:
Temp Units:
Save - +
1.
DEFAULT
4.
UC SINGLE
°C
Factory preset
Mode:
Temp Units:
Next - +
.
90˚
0ml
90˚
0ml
90˚
0ml

10
Programmable buttons
Program and change buttons accordingly
User Setup
.
Next Go
Calibrate conc pump
Calibrate Cold water
Calibrate Hot water
RTD speed
3 nger press
long hold
OPTION DESCRIPTION
Calibrate conc pump Will pump concentrate using FAST speed for 10 seconds and ask for weight
to be entered – then again the same at SLOW speed. (for accurate results
make sure system is primed / tubes are full with liquid)
Calibrate Cold water Will dispense water until owmeter clicks 200 pulses and then will ask to
enter weight. (for accurate results make sure system is primed / tubes are
full with liquid)
Calibrate Hot water will dispense hot water from the boiler for 10 seconds and ask for weight to
be entered.
RTD speed This is the speed of the pump (in % of full speed) If ow rate is too violent
this should be reduced
Chiller present Select yes if you are using a chiller to supply cold water

11
Operating Font
1. Push & Hold 2. Push & Release
Cleaning & Maintenance
RISK OF SCALDING
Turn off the boiler before cleaning to
prevent accidental triggering of a
dispense.
Beware of accidentally operating the font –
especially when cleaning around the push
buttons.
The exterior of this font may be cleaned
with a damp cloth and a light detergent.
Twist off and wash out flow straightener.
Do not use abrasive cloths or creams, as
this will spoil the finish of the font.
85°
100

Marco Beverage Systems Limited.
63d Heather Road,
Sandyford Industrial Estate,
Dublin 18
t: [phone]
f: [phone]
e: [e-mail]
www.marcobeveragesystems.com
NSF/ANSI 4
E337347