Mark-10 EK3-100 User manual

Series EK3
Ergonomics Kits
Quick Start Guide
Mark-10 Corporation
11 Dixon Avenue
Copiague, NY 11726
888-MARK-TEN
Tel: [phone]
[email protected]
www.mark-10.com
INSTALLING MESUR
MESUR®Lite
MESUR®gauge
90-day evaluation.
USB driver
in the user’s guide.
PC requirements
Series EK3 Ergonomics Kits
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

Thank you!
Thank you for purchasing a Mark-10 Series EK3 Ergo-
nomics Kit. Please read through this Quick Start Guide
and the complete force gauge User’s Guide before using
this kit.
Series EK3 Ergonomics Kits
IMPORTANT SAFETY CONSIDERATIONS
Force gauges are sensitive instruments that must be treated with care. Please
review the yellow safety information card included in the box.
LIST OF INCLUDED ITEMS:
Qty. Part No. Description EK3-100 EK3-200 EK3-500
1 M3-100 Force gauge, 100 lbF / 50 kgF / 500 N - -
1 M3-200 Force gauge, 200 lbF / 100 kgF / 1000 N - -
1 M3-500 Force gauge, 500 lbF / 250 kgF / 2500 N - - 
1 08-1022 AC adapter body with US, EU, UK, or
AUS prong 
1 08-1026 Battery (inside the gauge) 
1 09-1165 USB cable 
4 10-1023 Thumb screw, #6-32 X 1/2 
1 10-1021 Hex jam nut, #10-32 -
1 10-1108 Hex jam nut, 5/16-18 - 
1 AC1003 Double handle grip for Series 3/2 
1AC1003-1 Single handle grip for Series 3/2 
1 G1019 Padded attachment, square 
1 G1020 Padded attachment, rectangular 
1 G1021 Padded attachment, curved 
1 G1029 Flat attachment, #10-32F -
1 G1036 Flat attachment, 5/16-18F - 
1G1112 Padded attachment, circular 
1 12-1032 Carrying case, large 
2
3
-
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

Thank you!
this kit.
Series EK3 Ergonomics Kits
INSTALLING ACCESSORIES
Double and Single Handles
Qty. Part No.
1 M3-100
1 M3-200
1 M3-500
1 08-1022 AUS prong
1 08-1026
1 09-1165 USB cable
4 10-1023
1 10-1021 Hex jam nut, #10-32
1 10-1108 Hex jam nut, 5/16-18
1 AC1003
1AC1003-1
1 G1019
1 G1020
1 G1021
1 G1029
1 G1036
1G1112
1 12-1032 Carrying case, large
2
3
Series EK3 Ergonomics Kits
Attach the force gauge to the double
handle grip (AC1003) or single handle grip
(AC1003-1) by mating the male dowel pin in
the cradle to the corresponding hole in the
rear of the force gauge housing.
Then, fasten the gauge to the cradle with
four included thumb screws (10-1023), as
shown at left.
Attachments
Ergonomics attachments G1019, G1020,
G1021, G1029, G1036, and G1112 thread
onto the load cell shaft of the Series 3 force
gauge.
Fasten the attachment onto the shaft, as
shown at left.
Do not overtighten the attachment, or
load cell damage can occur!
The attachments may freely rotate on the
shaft, thereby self-adjusting to the shape of
an object. However, if a xed position is de-
sired, use an included jam nut, as follows:
1. Rotate the jam nut as high as possible up
the load cell shaft.
2. Rotate the attachment up to the jam nut,
then back o󰀨 until the desired position.
Tighten the nut against the attachment.
Friction between the nut and attachment
body will prevent the attachment from
loosening as shown at left.
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

EK3
Ergonomics Kits
32-1255
052022
INSTALLING MESUR®SOFTWARE
MESUR®Lite
Free basic data acquisition application, for data tabulation and exporting to Excel.
MESUR®gauge
Data tabulation, graphing, analysis, and reporting, with user-congurable start
and stop triggers and other tools. Compatible with all Mark-10 instruments. Free
90-day evaluation.
USB driver
For Mark-10 instruments and the model RSU100 RS-232 to USB converter. Re-
quired for communication with a PC. Follow the installation instructions provided
in the user’s guide.
PC requirements
Compatible with PCs running Microsoft Windows 7 or later. Minimum monitor res-
olution is 1108 x 758. A USB or RS-232C serial port is required. If USB communi-
cation is required, install the Mark-10 USB driver.
Series EK3 Ergonomics Kits
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]