Marmitek X10 SS12E User manual

S
S12
E
20472/20120530 • SS12E™
ALL RIGHTS RESERVED MARMITEK ©
USER MANUAL
SS12E ™

© MARMITEK
2
TABLE OF CONTENTS
TABLE OF CONTENTS....................................................... 2
SAFETY WARNINGS ......................................................... 3
HOW DOES MARMITEK X10 WORK? ............................. 4
ADRESSES ......................................................................... 4
SIGNAL RANGE ................................................................ 5
INSTRUCTIONS FOR USE SS12™ WIRELESS SWITCH ...... 7
INTRODUCTION ............................................................... 7
PROPERTIES...................................................................... 7
CHANGE OF THE HOUSECODE........................................ 7
CHANGE OF THE UNITCODE ........................................... 8
CHANGE OF THE BATTERY.............................................. 8
APPLICATIONS ................................................................. 8
FREQENTLY ASKED QUESTIONS ..................................... 9
TECHNICAL DATA .......................................................... 10
DECLARATION OF CONFORMITY.................................. 11
COPYRIGHTS .................................................................. 12

SS12 3
SAFETY WARNINGS
•To prevent short circuits, this product should only be
used inside and only in dry spaces. Do not expose the
components to rain or moisture. Do not use the
product close to a bath, swimming pool etc.
•Do not expose the components of your systems to
extremely high temperatures or bright light sources.
•In case of improper usage or if you have altered and
repaired the product yourself, all guarantees expire.
Marmitek does not accept responsibility in the case of
improper usage of the product or when the product is
used for purposes other than specified. Marmitek
does not accept responsibility for additional damage
other than covered by the legal product
responsibility.
•This product is not a toy. Keep out of reach of
children.
•Do not open the product (battery panel excepted):
the device may contain live parts. The product should
only be repaired or serviced by a qualified expert.
•Keep batteries out of the reach of children. Dispose of
batteries as chemical waste. Never use old and new
batteries or different types of batteries together.
Remove the batteries when you are not using the
system for a longer period of time. Check the polarity
(+/-) of the batteries when inserting them in the
product. Wrong positioning can cause an explosion.
•Automatic switching devices provide comfort, but can
also be dangerous. They can surprise people or can
ignite clothing hanging over an electric heat source.
Please be careful and take appropriate measures to
avoid accidents.

© MARMITEK
4
HOW DOES MARMITEK X10 WORK?
Marmitek X10 components use the existing mains wiring
to communicate (using Marmitek X10 signals). You can
build a complete system using the three different kind of
components of the Marmitek X10 System:
1. Modules: These components will receive Marmitek X10
signals and will switch or dim the attached lamp or
appliance. Examples of these modules are lamp modules
and appliance modules. These are available as build-in,
micro, DIN rail and plug-in modules.
2. Controllers: These components will transmit Marmitek
X10 signals and thus will control the Modules.
3. Transmitters:Wireless components like remotes. The
signals of these components will be received by a
controller with transceiver functionality (IRRF 7243, TM13,
CM15Pro…..). The Transceiver will translate the signals into
Marmitek X10 signals on the power line.
ADRESSES
Up to a maximum of 256 different addresses can be preset.
These are subdivided into a so-called HouseCode (A to P
incl.) and a UnitCode (1 to 16 incl.). The HouseCode can
also be set on the controllers, so that the controllers and
modules become part of the same system. The address can
be set either using code dials or by pressing buttons,
depending on the type of module.
The Marmitek X10 System uses standard commands, which
control all units with the same HouseCode at the same
time (e.g. all lights on, all units off, etc.).

SS12 5
SIGNAL RANGE
Range of Marmitek X10 signals over the Power Line
and how to increase the range.
The Marmitek X10 System is based on power line
communication. The range of the Marmitek X10 signals
very much depends on the local circumstances. On average
the range is a cable length of 80 meters.
If you have difficulties with the range of your
Marmitek X10 signals, please pay attention to the
following facts:
1. When more than one phase is used for your electrical
system, it is necessary to couple these phases for the
Marmitek X10 signals. For coupling you can use FD10
Phase Couplers/Filters. You only need to install a Phase
Coupler/Filter when your wall outlets and light switches
are divided over more than one phase (more than one
group is no problem). For bigger buildings or longer
distances we advice you to use an active repeater instead
of passive FD10’s.
2. It is possible that Marmitek X10 signals are attenuated
by devices and lights which are connected to the power
line. In a normal home situation this effect is negligible
(the Marmitek X10 system is using active gain control to
eliminate the effects). However, it is possible that a
particular device in your house is attenuating the signals so
much that the range of Marmitek X10 signals is decreased
significantly. When you have range problems, it is wise to
try to locate the device which is attenuating the signals
simply by unplugging devices from the power line, and
testing the differences in range for your Marmitek system.
When e.g. your conclusion is that e.g. your computer
monitor is attenuating the signal, you can use a FM10

© MARMITEK
6
Plug-in Filter between the power line and the monitor to
eliminate the effects.
Known devices which can cause attenuation are:
PC Monitors
PCs with heavy internal power supplies
Old Televisions
Copiers
Fluorescent Lights
Gas Discharge Lamps (Energy Saving Lamps)
3. Some (old) devices are able to disturb the signal by
transmitting noise on the power line. Because the
Marmitek X10 signals are transmitted on 120 kHz, only
noise on or near this frequency will have influence on the
range. When you use a FM10 Filter to connect this device
to the power line, the noise will be filtered.
4. The Marmitek X10 protocol has several mechanism to
avoid modules to be switched on or off by other sources
than your Marmitek X10 Controllers. However, it is
possible that the Marmitek X10 signals are disturbed by
e.g. baby phones which are in TALK mode (continuous
transmission). When these kind of signals are present on
the power line it is possible that the Marmitek X10 signals
will not come through.
5. The mains do not stop at the front door of your home.
Everything that is attached to mains nearby your home can
have influence on Marmitek X10 signals (e.g. heavy
machinery). If you think that your system is influenced by
devices out of your house, it is advisable to install FD10
Phase Coupler/Filter on each phase entering the house.
These filters will block signals coming into or going out of
your house, but will also match the impedance for the
mains. Hereby make your house Marmitek X10 compatible
for these units. The FD10’s will not only filter but will also
couple the phases (please see 1).

SS12 7
INSTRUCTIONS FOR USE SS12™ WIRELESS SWITCH
INTRODUCTION
Congratulations buying the Marmitek X10 SS12 wireless
switch. This is a super thin, elegant wireless switch. It is the
ideal solution for situations where an extra switch is
needed without installing wires. It is to install on walls,
glass, doors tables etc. and transmits high frequent signals
through walls and ceilings. The SS12 wireless switch
transmits radio graphical signals to an X10 Transceiver
TM13, IRRF7243 or Marmitek X10 Alarm station. Then the
Transceiver or Station transmits these signals via the in
your house already installed electric wiring. Through this
you can switch on and off your lighting (or apparatus)
connected to X10 receivers (lighting can be dimmed also).
The SS12 is completely wireless and battery powered.
PROPERTIES
The switches are delivered standard at HouseCode A.
CHANGE OF THE HOUSECODE
1. Press the left button ON and keep it pressed. The red
LED flashes shortly. After 15 seconds the present set-
up is shown: 1 flash is HouseCode A, 2 flashes is
HouseCode B etc.
2. Release the button ON.
3. Now press shortly for the desired HouseCode on the
same ON button (1x = A, 2x = B etc). The LED flashes
every time you press the button.
4. At the last time keep the button pressed. After 3
seconds the LED shows the set-up HouseCode. Now
release the button.

CHANGE OF THE UNITCODE
When setting up the UnitCode the left button is set up in
the desired UnitCode. The right button is always
automatically one UnitCode higher.
1. Press the left OFF button and keep it pressed. The red
LED flashes shortly. After 15 seconds the present set
up is shown: 1 flash is UnitCode 1, 2 flashes is
UnitCode 2 etc.
2. Release the OFF button.
3. Now press shortly for the desired UnitCode on the
same OFF button (1x = 1; 2x = 2 etc.) The Led flashes
every time you press the button.
4. At the last time keep the button pressed. After 3
seconds the LED shows the set-up UnitCode. Now
release the button.
CHANGE OF THE BATTERY
Remove the right rocker switch at
the front of the SS12 and replace
the battery.
Use an identical 12V Alkaline
battery (type A23). Mind the
polarity when replacing.
APPLICATIONS
With the Marmitek X10 SS12 wireless switch you can
activate pre-programmed macros in the CM15Pro
computer interface.
You can also use the SS12 as a central operation panel for
your Marmitek installation.
© MARMITEK
8

SS12 9
FREQENTLY ASKED QUESTIONS
What is the reason for modules to switch on/off
spontaneously?
It is possible that a Marmitek X10 System is installed at one
of your neighbours using the same HouseCode. To solve
this problem try to change the HouseCode of your system,
or have FD10 Phase Coupler/Filter installed at your
incoming mains.
My modules will not respond to my controller.
Make sure that the HouseCode on all Modules and
Controllers are set to the same HouseCode (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least
one Transceiver or Marmitek Security Console installed in
your house. These components will translate the radio
signals to the Marmitek X10 signal on the power line. Only
one Transceiver should be installed for all remotes and
sensors set to the same House Code.
The other modules do not respond to signals of the
SS12. What can be the problem?
• Check if the SS12 has been set-up correctly. The easiest
way to do this is to give again the correct HouseCode to
the top left button.
• Has the battery been placed correctly?
• The SS12 uses a Transceiver module (TM13, IRRF7243 or
one of the Marmitek X10 alarm stations). Check if it works
properly, for instance to use another remote control.
• Maybe the range of the SS12 is not sufficient for your
purpose; if so, when using a TM13, place an extra TM13 in
the neighbourhood of your SS12.
Do you still have questions? Please check out
www.marmitek.com for more information.

TECHNICAL DATA
Supply: 1 x A23 12V Alkaline Battery
(supplied)
RF range: Up to 30m free field, up to 20m
through walls and ceilings
RF frequency: 433,92 MHz
RF power: 10mW
X10 Key codes: On, off, dim, bright
Ambient temperature: - 10° C to + 50° C (operation)
- 20° C to + 70° C (storage)
Dimensions: 80 x 80 x 20 mm
Environmental Information for Customers
in the European Union
European Directive 2002/96/EC requires that the
equipment bearing this symbol on the product
and/or its packaging must not be disposed of
with unsorted municipal waste. The symbol indicates that
this product should be disposed of separately from regular
household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment
via designated collection facilities appointed by the
government or local authorities. Correct disposal and
recycling will help prevent potential negative
consequences to the environment and human health. For
more detailed information about the disposal of your old
equipment, please contact your local authorities, waste
disposal service, or the shop where you purchased the
product.
© MARMITEK
10

DECLARATION OF CONFORMITY
Hereby, Marmitek BV, declares that this SS12 is in
compliance with the essential requirements and other
relevant provisions of the following Directives:
Directive 1999/5/EC of the European Parliament and of the
Council of 9 March 1999 on radio equipment and
telecommunications terminal equipment and the mutual
recognition of their conformity
Directive 2004/108/ec of the european parliament and of
the council of 15 December 2004 on the approximation of
the laws of the Member States relating to electromagnetic
compatibility
Directive 2011/65/EU of the European Parliament and of
the Council of 8 June 2011 on the restriction of the use of
certain hazardous substances in electrical and electronic
equipment
MARMITEK BV
P.O. BOX 4257
5604 EG EINDHOVEN
NETHERLANDS
0681
SS12 11

© MARMITEK
12
COPYRIGHTS
Marmitek is a trademark of Pattitude B.V.
SS12™ is a trademark of Marmitek B.V. All rights reserved.
Every effort has been made to ensure that the information
in this manual is accurate. Marmitek is not responsible for
printing or clerical errors.
Copyright and all other proprietary rights in the content
(including but not limited to model numbers, software,
audio, video, text and photographs) rests with Marmitek
B.V. Any use of the Content, but without limitation,
distribution, reproduction, modification, display or
transmission without the prior written consent of
Marmitek is strictly prohibited. All copyright and other
proprietary notices shall be retained on all reproductions.
Other company and product names mentioned herein may
be trademarks of their respective companies. Mention of
third-party products is for informational purposes only and
constitutes neither an endorsement nor a
recommendation. Marmitek assumes no responsibility with
regard to the performance or use of these products.

SS12 13

© MARMITEK
14

SS12 15