Marpo Kinetics VLT Operating manual

Marpo Kinetics, Inc.
1306 Stealth Str. Suite. A , Livermore, CA 94 1 • (92 ) 606-6919 • www.marpokinetics.com
- VLT –
IMPORTANT
INFORMATION
TO SAFELY REMOVE PRODUCT
FROM THE PACKAGE,
FOLLOW THESE INSTRUCTIONS
FOR SAFETY, TWO OR MORE PERSONS MUST ASSIST IN THE PACKAGE
REMOVAL AND PRODUCT INSTALLATION.
IT IS BEST THAT THE REMOVAL OF THE PRODUCT FROM THE PACKAGE, BE
DONE NEAR THE AREA WHERE THE PRODUCT WILL BE PLACED FOR USE.
THIS WILL ELIMINATE THE NEED TO MOVE THE PRODUCT AROUND AFTER
IT IS ASSEMBLED. SHOULD THERE BE A NEED TO MOVE THE PRODUCT
AROUND, THERE MUST ALWAYS BE AT LEAST TWO PERSONS DOING THIS
OPERATION TO AVOID ANY INJURIES. TO PROTECT THE ROPE FROM SNAGS,
IT MUST BE KEPT WRAPPED UNTIL IT IS READY TO BE STRETCHED ONTO
THE PULLEYS.
REMEMBER, ALWAYS KEEP ALL BODY PARTS AWAY FROM PULLEYS OR ANY
OTHER MOVING PARTS AS THESE ELEMENTS CAN CAUSE SERIOUS INJURY.
MINORS SHOULD NEVER BE ALLOWED TO OPERATE THE MACHINE WITHOUT
THE CONSENT AND CONSTANT SUPERVISION OF AN ADULT.
Securing Equipment
All MARPO KINETICS eq ipment m st be sec red to the floor to stabilize and eliminate
rocking or tipping. This m st be performed by a licensed contractor. DO NOT se the
eq ipment if it is not set p and located on a solid, level s rface.
Make s re that each machine is set p and operated on a solid, level s rface.
DO NOT install equipment on an uneven surface.
Use fasteners having a minim m of 500 lbs. tensile capacity (3/8" grade 2 bolts or better).
If legs/frame does not contact s rface, DO NOT p ll down with anchors. Shim any leg or
frame not in contact with s rface sing flat washers.
1

Marpo Kinetics, Inc.
1306 Stealth Str. Suite. A , Livermore, CA 94 1 • (92 ) 606-6919 • www.marpokinetics.com
1. Remove all wrapping material.
CAUTION: Do not use blades to cut wrapping material since it may damage the unit.
2. Remove all contents from the box:
1 MA N UN T
1 BOOM
1 FRONT EXTENS ON
1 M D CROSS BAR
1 SEAT
1 TOP PULLEY GUARD
2 LEVEL NG FEET
1 SET (LEFT AND R GHT) BOOM BASE COVERS
1 USER MANUAL
1 PACKAGE REMOVAL NSTRUCT ONS
1 WORKOUT POSTER
2

Marpo Kinetics, Inc.
1306 Stealth Str. Suite. A , Livermore, CA 94 1 • (92 ) 606-6919 • www.marpokinetics.com
3. One person should hold on to the MA N UN T while a second person attaches it to the
M D CROSS BAR using the provided 1/4-20 X 2.5” screws. The foot pads of the M D
CROSS BAR should be touching to the ground. The bigger diameter washers (1.25”
OD) go next to the head of the screws, under the M D CROSS BAR. nsert screws from
the bottom up through the M D CROSS BAR so the nuts end up on top. The 1” OD
washers go on top where the nuts are. Tip … use small pieces of tape to keep the bolts
from falling off when connecting the M D CROSS BAR to the MA N UN T. Have a
second person hold the unit from falling over while attaching the M D CROSS BAR.
CAUTION: Leaving the prod ct ns pported before the nit is attached to the
MID CROSS BAR co ld ca se the nit to fall over and ca se inj ry and/or prod ct
damage.
4. f the product rocks side-to-side or front to back, adjust the nuts on the 2 threaded
LEVEL NG FEET at the back of the unit. When done, re-tighten the nuts well.
5. Attach the ADJUSTABLE BOTTOM PULLEYS (W TH BRACKETS) to the MA N
UN T. Use provided screws (screws temporarily attached to the MA N UN T).
6. Attach the FRONT extension
3
REAR VLT
1/4” D X 1.00” OD
WASHER
1/4” D X 1.25” OD
WASHER
3/8”X 4”
BOLT
2 PC.
1/4”X 2.5”
BOLT
8 PC.
USE PROV DED
ANCHORS TO SECURE
UN T TO THE GROUND

Marpo Kinetics, Inc.
1306 Stealth Str. Suite. A , Livermore, CA 94 1 • (92 ) 606-6919 • www.marpokinetics.com
7. Connect the BOOM to the MA N UN T with the 3/8-16 bolts, nuts and washers. .
8. Attach the COVERS FOR THE BOOM BASE first to the main cover flange and then to
the BOOM with the one screw at the top of the cover.
NOTE: T S NORMAL FOR THE ROPE TO HAVE SLACK AS T ALLOWS FOR WR ST
AND ARM FREEDOM DUR NG USE.
4
Boom
connection Plastic Covers
for Boom Base
Top Pulley
Guard
Top Pulley

Marpo Kinetics, Inc.
1306 Stealth Str. Suite. A , Livermore, CA 94 1 • (92 ) 606-6919 • www.marpokinetics.com
9. The electronic display works with two AAA batteries. To replace the batteries remove
the 4 screws that connect the D SPLAY TRAY to the main covers. Slowly pull the
D SPLAY TRAY away from the machine. Disconnect the display from the main
harness. Next remove the 4 machine screws that connect the D SPLAY to the the
D SPLAY TRAY to access the battery cover on the back of the D SPLAY.
5
Remove these
screws first and
watch out for the
harness as pulling
the display tray
away from the
main covers
Remove these
screws next to
access batteries.