marsden I-400SS User manual

USER MANUAL
I-400SS
Please take time to read these
instructions before starting
to use the scale

Contents
Product Specification 3
Safety Instructions 4
Before Using the Scale 6
Replacing the Battery 6
Operation: Basic Functions 7
Operation: Advanced Functions 8
Error Messages 12
Page 2

Product Specification
Model
Marsden I-400SS
Units of Measure
Kg/lb
Function Keys
HOLD, TOTAL, LB/KG, GROSS, TARE, ZERO,
PRINT/ON/OFF
Stabilization Time
1-2 Seconds
Operating Temperature
-20°C to 40°C
Protection level
IP68
Power Supply
7.4V/4Ah lithium rechargeable battery
Mains lead
Indicator Display
40mm LCD display with 6 active digits
Please note: Marsden’s policy is one of continuous development and therefore
we reserve the right to change product specification without notice.
Indicator images in this manual are for illustration purposes only.
Page 3

Safety Instructions
Before putting this scale into use, please read with care the information given in this user
manual, which contains important instructions for proper installation, use and maintenance
of the device.
Marsden/the manufacturer shall not be liable for damages arising from failure to heed the
following instructions:
•When using electrical components under increased safety requirements, always
comply with appropriate regulations.
•Inappropriate installation/use will render the warranty null and void.
•Ensure the voltage marked on the power supply unit matches your mains supply.
•Observe the permissible ambient temperatures for use.
•The device meets the requirements for electromagnetic capability. Do not exceed
the maximum values specified in the applicable standards.
•Do not use this pallet truck unless you are familiar with it and have been trained and
authorized to do so.
•Avoid using this pallet truck on a sloping ground.
•Never place any part of your body in the lifting mechanism or under the forks or
load. Do not carry passengers.
•Do not overload the truck, or handle unstable or loosely stacked loads.
•Ensure loads are distributed as evenly as possible on the scale.
•Lower the forks to their lowest setting when the pallet truck is not in use.
If you have any problems, contact Marsden/your local dealer/your service partner.
Cleaning
•This scale can be washed down with care. Always disconnect the scale from the
mains power supply before cleaning.
Maintenance
•Check the pallet truck daily for wear and tear, particularly if it is in regular use. Pay
special attention to the wheels, axles and forks, as well as the lift and lower control.
•Moveable parts will require periodic lubrication. Use motor oil or grease to lubricate.
•Air may enter the unit when seals have been replaced. Lift the control lever to the
lower position, then move the handle up and down several times.
•You can book an accuracy check with the Marsden Service team on 01709 364296.

Before using the Scale
•Please read these instructions fully before using your I-400SS Indicator.
•Ensure the battery is fully charged before first use.
Replacing the Battery
•Loosen the screws on the battery cover and remove the cover.
•Open the screw on the battery and pull the battery out of its socket.
•Replace with the new battery. Replace the cover plate and screw into position.
Page 4

Operation: Basic Functions
Switching the Scale on/off
Press PRINT/ON/OFF to power-on the
scale. When the scale shows 0.0 it is
ready for weighing.
To switch the scale off, press and hold
PRINT/ON/OFF for three seconds. The
scale will now power down.
Setting the Scale to Zero
If at any time the reading shows
anything other than 0.0 when there is
nothing on the scale, you can reset
the display by pressing ZERO once.
Page 5

Operation: Advanced Functions
Hold Function
With the scale switched on, add an
item to the base.
Press HOLD once. The scale will lock
onto and stabilise the weight reading
for the item. The reading will remain
displayed after the item is removed.
Press HOLD again to disable the
Hold function and return the scale to
0.000.
Tare Function
Page 6

Place the item you wish to deduct
the weight of (such as a pallet or
empty box) on the scale and
press TARE.
The scale will show a minus reading.
Weigh as normal and the negative
weight reading will be deducted from
the total weight.
Weigh as normal and the negative
weight reading will be deducted from
the total weight.
Page 7

Once you have finished weighing,
press TARE again to remove the tare
value and return the scale to 0.0.
Switching Between Kg and lb
To switch the weight reading
between kg and lb, press LB/KG.
The LCD panel will indicate whether
the reading is showing in kg or lb as
shown on the left.
Setting the Screensaver
To save battery power, the screen can
power off after a set period of time.
To set the time out function, with the
indicator switched on and nothing on
the scale, press and hold down HOLD
until ‘F1’ is displayed.
Use TARE and ZERO as arrow keys to
scroll to F3
Page 8

Press PRINT/ON/OFF, and F3.1
should appear on the screen. Press
PRINT/ON/OFF again.
Use LG/KG, GROSS, TARE and ZERO
as arrow keys to select the power-off
delay (up to 60 mins).
Press PRINT/ON/OFF once and HOLD
twice to set the time out period and
return to normal weighing mode.
.
Error Messages
Display
Problem
Solution
Unable to reset after start
up
Ensure there is nothing on
the scale when switching
on
Possible scale overload
Remove weight from the
scale
Scale is below zero
Press zero to re-zero the
scale
Page 9

Out of balance range
Remove any weight from
the scale and try again
Invalid operation
EEPROM error
Switch the scale on again; if
the error message still
shows, contact your
dealer/Marsden
AD initialization error
Switch off the scale and
restart. If the error occurs
again, contact your
dealer/Marsden
NOTE: If the scale shows any error message other than those listed above, please contact
Marsden on 01709 364296.
Page 10

Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
Manufacturing and Distribution:
Unit 7, Centurion Business Park,
Coggin Mill Way,
Rotherham,
S60 1FB
Head Office:
Unit 1, Genesis Business Park,
Sheffield Road,
Rotherham
S60 1DX
www.marsden-weighing.co.uk