Marshall Amplification 180150 User manual

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
180166 RV011821
Copyright © 2021 Marshall Air Systems, Inc
All Rights Reserved
Supplier Name: MARSHALL AIR SYSTEMS, INC.
Address: 419 Peachtree Drive South
Charlotte, NC 28217
Model #: ____________________________
Serial #’: ____________________________
Date Received: ____________________________
Date Installed: ____________________________
Telephone #: [phone]
Fax #: [phone]
Service Referral #:800-722-3474
Local Service: ____________________________
Local Service #: ____________________________
PRODUCT DESCRIPTION
The 180150 LED Light Retrofit Kit replaces existing
incandescent light bulbs for RR5-42 and RR5-48.5
Fry Dump Stations. It provides a bright pleasing light
that fully illuminates the dump station work area. LED
lights are extremely energy efficient, long lasting and
are constructed with no glass components for greater
safety.
The LED Light Retrofit Kit fits into one existing pair of
light sockets. The other pair of light sockets is covered
by a Light Socket Cover that is provided with the kit.
GENERAL SPECIFICATIONS
Model: 180150
Height: 4.000”
Depth: 5.500”
Width: 39.000”
Voltage: 120 Volts
Amps: 75 mA
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.
WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATION AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
KEEP THIS MANUAL IN A SAFE PLACE AND RETAIN FOR FUTURE USE.

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
180166 RV011821
Copyright © 2021 Marshall Air Systems, Inc
All Rights Reserved
TABLE OF CONTENTS
INSTALLING THE LED LIGHTS..................................................................................................1 - 5
REPLACEMENT PARTS..................................................................................................................6

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
180166 RV011821
Copyright © 2021 Marshall Air Systems, Inc
All Rights Reserved

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
1
180166 RV011821
Copyright © 2020 Marshall Air Systems, Inc
All Rights Reserved
BEFORE INSTALLING THE LED LIGHTS
1. BEFORE INSTALLING THE LED LIGHTS, UNPLUG POWER FOR THE DUMP STATION.
FAILURE TO DO SO MAY RESULT IN ELECTRICAL SHOCK.
2. To prevent injury, allow dump station to cool if needed. Do not install while dump station is
hot.
3. If there is a Carton Holder loosen two screws to lift off Carton Holder.
4. Lift off and remove Heat Guard.
5. After the dump station has been unplugged and cooled remove all four existing light bulbs.
6. Shine a flashlight into the two empty light sockets on the right side. Inspect for any debris or
obstruction. Remove any obstruction such as a broken off tip of a previous light bulb.

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
2
180166 RV011821
Copyright © 2020 Marshall Air Systems, Inc
All Rights Reserved
ADJUST THE LED LIGHTS IF REQUIRED
1. If light sockets on the right side are unable to be used, the LED Light Kit can be adjusted as
shown above to use light sockets on the other side. If light sockets on the right side can be
used skip this step and go to the next instruction.

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
3
180166 RV011821
Copyright © 2020 Marshall Air Systems, Inc
All Rights Reserved
SCREW IN FLANGED ADAPTERS
1. Before screwing the flanged adapters into the light sockets unplug the flanged adapters from
the black quick disconnector to avoid stressing the wires.
2. Screw the flanged adapters into the light sockets tight to make good electrical connections.
3. Loosen the 4 screws that hold the mounting flange of the LED Light Kit and the 3 screws
that adjust the light adapter covering for the light bar. Be sure not to back the screws all the
way out.
4. Hold the LED Light Kit up to the front of the dump station and plug flanged quick disconnect
adaptors back into the LED light bar before positioning the kit. Be sure to match up the quick
disconnect male clips to the female clips.

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
4
180166 RV011821
Copyright © 2020 Marshall Air Systems, Inc
All Rights Reserved
POSITION THE LED LIGHT KIT
1. Place the mounting flange of the LED Light Kit against the front of the dump station as
shown.
2. The two flanges on the LED light kit should grip the front lip of the dump station.
3. The flanged adapter covering should fit up into the light bar over the light sockets as shown.
4. Make certain that no wires are protruding from the flanged adapter covering.

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
5
180166 RV011821
Copyright © 2020 Marshall Air Systems, Inc
All Rights Reserved
ATTACH THE LED LIGHT KIT
1. Use four screws that are provided with the kit to secure the LED Light Kit in place.
2. Ensure the bottom of the mounting bracket is flush with the bottom of the dump station.

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
6
180166 RV011821
Copyright © 2020 Marshall Air Systems, Inc
All Rights Reserved
ATTACH THE LIGHT SOCKET COVER
1. The LED Light Kit comes with two Light Socket Covers. Select the Light Socket Cover that fits
tightly over the exposed light sockets.
2. Push the Light Socket Cover up into the light bar until it snaps into place completely covering
the left side light sockets.
3. Replace the Heat Guard.
4. Plug in dump station and turn power on.
IF THE LED’S DO NOT COME ON
1. Check sockets to make sure they are tightened.
2. Remove sockets and once again check for debris (make sure power cord is unplugged).
3. Check internal cords that plug into LED strips for tightness.

OWNER’S MANUAL
MODEL 180150 –LED LIGHT RETROFIT KIT
7
180166 RV011821
Copyright © 2020 Marshall Air Systems, Inc
All Rights Reserved
REPLACING THE LED LIGHTS
1. The LED Light Kit comes with two replaceable LED Lights.
2. Remove two center screws from the front of the LED Light Kit that hold the Center Bracket as
shown.
3. The remainder of the LED Light Kit will then hang by the flanged adapter wires. Unplug the
flanged adapters from the black quick disconnectors.
4. Unplug the LED Lights and replace with new LED Lights.
5. Reconnect the black quick disconnectors and replace two screws that hold the Center Bracket
as shown.
6. Make certain that no wires are protruding from the flanged adapter covering.
REPLACEMENT PARTS LIST
PART NO.
DESCRIPTION
QUANTITY
504691
Light, LED 18” long
2