Masport F10000 HW User manual

wood fires.
A B E F G H R§
250 300 200 445 680 607 858
200 300 200 395 680 607 858
§ Valid only when the room walls are at 90°to each other.
PRT. NO.
DATE:
* Air-Group Special Insulated Flue Kit is same as AHD Special Insulated Flue Kit.
This fire has been tested and complies to the Australian/New Zealand Standard AS/NZS 2918:2001 and all
installations must be in accordance with the minimum clearances to combustibles indicated in these instructions.
CLEARANCE REQUIREMENTS
The minimum clearances to combustables may be reduced if the combustable walls are shielded with an approved
non-combustable material. Details of suitable materials and appropriate clearance reduction factors are present in
Section 3 of AS/NZS 2918:2001.
F10000 HW
F12000 HW
FAIRHAVEN
FLOWMET UNIVERSL FLUE SYSTEM
AIR-GROUP SPECIAL INSULATED FLUE KIT *
MODEL FLUE HEAT SHIELD
AUSTRALIA
MINIMUM DISTANCES TO HEAT SENSITIVE WALLS (mm)
02.10.2017
595772
These instructions must be used in conjunction with the 'General Installation Instructions' for Masport
F10000 HW
F12000 HW
FAIRHAVEN
‡ Note: Clearances are for fire hazard only. For durability of finishes or surfaces you should contact the relevant
manufacturer for their specification. Masport accepts no responsibility for the deterioration of surfaces or finishes.
MODEL
INSTALLATION SPECIFICATION SHEET
POSITIONING YOUR FREE-STANDING WOODFIRE
Page 1 of 5

PARALLEL INSTALLATION
MINIMUM FLOOR PROTECTOR DIMENSIONS IN mm
# DIMENSIONS IN THE TABLE ARE VALID ONLY WHEN THE FIRE IS EXACTLEY AT ITS MINIMUM
ALLOWABLE WALL CLEARANCE.
Flue
Shield
Floor
Protector
height
A# C# D F I J K# P2 P3 W
FUF 250
300 103 445 665 965 1160 610 195 760
AGA 200
300 103 395 665 965 1110 610 195 760
FUF = FLOWMET UNIVERSAL FLUE SYSTEM
AGA = AIR GROUP / AHD SPECIAL INSULATED FLUE KIT WITH 900mm S/S REFLECTOR SHIELD
AFP = ASH FLOOR PROTECTOR
AUSTRALIA - ALL WITH FLUE HEATSHIELD
MODEL Floor Protector
Type Ø
F10000 HW
F12000 HW
FAIRHAVEN
FLOOR PROTECTOR (Hearth) REQUIREMENTS
NOTE: Where a fan is being fitted, you may prefer to increase the ‘A’ dimension to 100 mm to provide easier access for
servicing. If so, the amount you add to ‘A’ to bring it to 100 mm must also be added to the ‘C’ and ‘S’ dimensions.
# Valid only when the fire is exactly at its minimum allowable wall clearance.
Ø for minimum constructional requirements see general installation instructions.
AFP
AFP
Page 2 of 5

FLOOR PROTECTORS (Hearth) REQUIREMENTS
CORNER INSTALLATION
MINIMUM FLOOR PROTECTOR DIMENSIONS IN mm
# DIMENSIONS IN THE TABLE ARE VALID ONLY WHEN THE FIRE IS EXACTLEY AT ITS MINIMUM
ALLOWABLE WALL CLEARANCE.
FUF 300 200 607 1573 1347 715 858 AFP
AGA 300 200 607 1573 1347 715 858
AFP
FUF = FLOWMET UNIVERSAL FLUE SYSTEM
AGA = AIR GROUP / AHD SPECIAL INSULATED FLUE KIT WITH 900mm S/S REFLECTOR SHIELD
AFP = ASH FLOOR PROTECTOR
N R#
F10000 HW
F12000 HW
FAIRHAVEN
E H# M#
MODEL Flue
Shield
Floor Protector
Distance above
Floor
C L#
FLOOR
PROTECTOR
TYPE
AUSTRALIA
Page 3 of 5

P1 P3 H W S1 S2 S3 S4
F10000HW
620 195 800 760 340 170 20
605
F12000HW
620 195 800 760 340 170 20
605
FAIRHAVEN
620 195 800 760 340 170 20
605
FREE STANDING FIRE DIMENSIONS
MODEL
Seismic Restrain - In New Zealand and some part of Australia, it is required that the wood fire and floor
protector are secured to prevent shifting in the event of an earthquake. This is best done by fastening the
wood fire right through the protector to the floor, using two 8mm dynabolt or 8mm coach screws or toggle
fasteners for wooden floors of appropriate length.
Seismic Restrain
Holes Location
Page 4 of 5

THE "
AIR-GROUP SPECIAL INSULATED FLUE KIT
" WHICH IS SAME AS "
AHD SPECIAL
INSULATED FLUE KIT
" MUST BE MODIFIED AS PER DIAGRAM BELOW FOR F7000 HW 175MM
FLUE KIT INSTALLATIONS IN AUSTRALIA.
FOR AUS INSTALLATION WITH
FLOMET UNIVERSAL FLUE SYSTEM
, PLEASE REFER TO THE
SPECIFIC FLUE INSTALLATION INSTRUCTIONS FROM FLUE MANUFACTURER.
Page 5 of 5