Masport Monaco User manual

Page 2
B Vent Gas Flue Kit 552323
Gasfire Flue Kits
This kit contains: Gas Cowl, Outer Liner 900mm,
Ceiling Plate, Black Trim Liners 900mm x 3, Inner Flue
Crimped 900mm x 3, Inner Flue Plain 900mm x 1.
Cardrona (Baltimore)
Product Description Part Number
Will fit Masport Cardrona, Monaco, Geneva & Vienna Gas Fires
Monaco
Geneva (F38)
Vienna (F33)

Page 3
Will fit Masport Cardrona, Monaco, Geneva & Vienna Gas Fires
This flue kit has been manufactured in accordance with AS5601 2002. To ensure safety
this flue kit must be installed as outlined in these instructions. Heater and flue
clearances from combustible walls must be in accordance with Masport heater
specifications and AG601.
1 Locate the heater in its proposed position and mark a point on the ceiling that is
directly above the centre of the heater flue outlet. Check that the heater location
allows the flue outer shield to clear all structural roof timbers.
2 Cut a 150mm square hole in the ceiling using centre mark as guide. Directly above
cut a 150mm round hole in the roof (or square hole) to accommodate the flue
outer heat shield.
3 Fit nogs around ceiling and roof holes in ceiling space if required
4 Position the outer heat shield so that it is flush with the underneath of the
ceiling and protrudes through the roof the required height.
The Flue is required to be at least 500mm above the nearest point on any part of the roof.
It is recommended to extend the Flue above the ridgeline as to help prevent down drafting
issues. Additional outer heat shields may have to be added to comply with required
standards and local wind conditions.
5 Fix an appropriate weather seal around the flue outer heat shield and seal on to
the roofing material.
6 Insert one flue trim length into flue outer heat shield (Ensure swaged end of trim
heat shield is facing heater) a sufficient distance to allow the lower flue trim
length(s) to be placed on top of the heater. Fix flue trim lengths together ensuring
seams are in line.
7 Assemble the 100mm galvanized flue pipes together ensuring the seams are in
line and the plain end flue is at the heater end using pop rivets or self taping
screws. We recommend sealing all flue joints with appropriate sealer.
8 Lift flue trim lengths sufficiently to insert ceiling plate over heater flue spigot
ensuring the plate is up the correct way and fit ceiling plate to ceiling using screws
provided.
9 Lower the 100mm galvanized flue pipes from the roof into the flue outer heat
shield and onto the heater flue outlet. Lift the flue trim for access to check
connection and recommended sealing.
10 Lower Flue Trim onto (secure to heater top with appropriate bracket) or into
heater top depending on model
11 Ensure inner flue length is 10mm higher than the outer heat shield. Fit gas cowl
by pushing over flue outer heat shield.
12 Start fire and run for at least 15 minutes check flue spill as shown in installation
manual.
Note: It is the responsibility of the installer to ensure that the installation of this flue kit complies
with AS5601 2002 and local body requirements.
Flue Kit Part
Number:
552323
Gasfire Flue Kit Installation Instructions
Inner Flue
100mm dia x
900mm x 3
Gas Cowl
Ceiling Plate
Trim Heat
Shield
145mm dia x
900mm x 3
Outer Heat
Shield
150mm dia
x 900mm
Lower Inner
Flue 100mm
dia x 900mm

Page 4
Geneva (F38)
‘B’ Vent Only
Off Set Kit - Room
(Painted)
Part No: 552332
Off Set Kit - Roof
(Unpainted)
Part No: 552333
Extension Kit - Room
(Painted)
Part No: 552330
Extension Kit - Roof
(Unpainted)
Part No: 552331
Off Set and Extention Kit
Will fit Masport Geneva, Cardrona & Monaco Gas Fires
Cardrona (Baltimore)
Monaco