Master MH-80TBOA-KFA User manual

MODEL NUMBERS:
MH-80TBOA-KFA
CONSUMER: READ AND SAVE THESE IMPORTANT INSTRUCTIONS
GENERAL HAZARD WARNING: READ AND UNDERSTAND
ALL OF THE INSTRUCTIONS IN THIS MANUAL BEFORE
ASSEMBLING, STARTING, OR SERVICING THE HEATER. Be sure
to comply with the instructions and warnings provided with this heater. Failure to comply can
result in fire or explosion that can cause property loss, bodily injury, or loss of life. Persons
who are impaired or under the influence of alcohol or drugs should not operate heater.
Only persons who can follow and understand these instructions should operate or service
this heater. If you need heater info; such as an operating manual, labels, etcetera, contact
Pinnacle Climate Technologies at 800-641-6996.
DANGER
NOT FOR USE IN RESIDENTIAL LIVING AREAS OR IN ENCLOSED
SPACES WITHOUT ADEQUATE VENTILATION. THIS HEATER
IS NOT FOR USE WHERE EXPOSED TO THE WEATHER, AND
INDOOR USE ONLY IN WELLVENTILATED AREAS. INDOOR USE PERMITTED ONLY FOR:
THE TEMPORARY HEATING OF ADEQUATELY VENTILATED BUILDINGS OR STRUCTURES
UNDER CONSTRUCTION, ALTERATION OR REPAIR. This is an unvented portable heater
that uses air (Oxygen) from within the area in which it is used. Failure to provide adequate
combustion and ventilation air will result in asphyxiation, carbon monoxide poisoning, bodily
injury or death. Refer to “Ventilation” on Page 5.
FACTORY ID: 500
DANGER
Sauk Rapids, MN 56379 USA • Toll Free [phone]
Fax: [phone] • Web: www.masterindustrialproducts.com • Email: [email protected]
© 2023 Pinnacle Climate Technologies, Inc. MAKD-435Master is a registered trademark of Pinnacle Climate Technologies, Inc.
BATTERY OPERATED
KEROSENE FORCED AIR HEATER
User’s Manual & Operating Instructions
Locating Your Serial Number:
Your serial number can be found on a white label on the right side cover of your heater. For Example:
150812779. Have your Serial Number ready before calling customer service at 800-641-6996.
Heater is intended for use without ducts. DO
NOT connect to ducts. DO NOT tamper with
the unit. Have a competent serviceman make
any adjustment or repair. DO NOToperate the unit in close proximity to
combustible surfaces or materials. Allow the unit to cool before shut down.
Remove battery if the heater is not in use.
WARNING

2
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
MASSACHUSETTS RESIDENTS: Massachusetts state law prohibits the use of this heater in
any building which is used in whole or in part for human habitation. Use of this heating device
in Massachusetts requires local fire department permit (M.G.L.C. 148, Section 10A).
NEW YORK CITY RESIDENTS: The New York City Fire Code prohibits the storage, handling
and use of kerosene fueled heaters for space heating. Any person violating that provision may
be punished by a fine up to $10,000 and a term of imprisonment of up to 6 months.
Look for this icon throughout the manual for helpful tips on how to assemble, use and
clean your KFA Heater.
THE INSTALLATION OF THE EQUIPMENT SHALL BE IN ACCORDANCE WITH THE
REGULATION OF AUTHORITIES HAVING JURISDICTION AND CSA STANDARD B139.
WARNING: This product can expose you to chemicals, including leadand lead
compounds, whichareknown to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
DO NOT START THE HEATER WHEN EXCESS OIL HAS ACCUMULATED.
DO NOT START THE HEATER WHEN THE CHAMBER IS HOT.
WARNING
WARNING
FIRE, BURN, INHALATION AND EXPLOSION HAZARD. Keep com-
bustibles such as; building materials, paper or cardboard a safe dis-
tance away from the heater as recommended by these instructions.
Never use the heater in spaces which contain products such as; gasoline, solvents, paint
thinners, dust particles, volatile or airborne combustibles or any unknown chemicals. This is
an unvented portable heater. It uses air (Oxygen) from the area in which it is used. Adequate
combustion and ventilation air must be provided. Refer to “Ventilation” on page 5. Bulk fuel
storage should be a minimum of 25 feet (7.6 m) from heater.
WARNING
DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND
THOROUGHLY UNDERSTAND THESE SAFETY AND OPERATING
INSTRUCTIONS.
Failure to comply with the precautions and instructions provided with
this heater can result in death, serious bodily injury, property loss or damage from the hazards of
fire, soot production, explosions, burns, asphyxiation or carbon monoxide poisoning. Only per-
sons who can read and understand these instructions should use or service this heater.
WARNING
SAFETY INFORMATION
Safety Information.....................................................2-3
What’s in the Box...........................................................4
Specifications .................................................................4
Features...........................................................................4
Assembly Instructions..................................................4
Operation ....................................................................5-6
Battery Operation Instructions...................................7
Maintenance...............................................................8-9
Wiring Diagrams ..........................................................10
Troubleshooting Guide ............................................... 11
Exploded View
............................................................ 12
Parts List ........................................................................ 13
Limited Warranty.......................................................... 14
TABLE OF CONTENTS

3
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
SAFETY INFORMATION CONT.
ALWAYS use only the electrical power (voltage and
frequency) specified on the model plate of the heater.
ALWAYS use only three-prong, grounded outlet and
extension cord.
ALWAYS use only 14 AWG or better extension cord.
ALWAYS unplug the heater when not in use.
ALWAYS install the heater so that it is not directly
exposed to water spray, rain, dripping water, or wind.
NEVER use fuels such as gasoline, benzine, paint
thinners or other oil compounds in this heater.
NEVER refill the heater’s fuel tank while the heater
is operating or still hot. This heater is EXTREMELY
HOT while in operation.
NEVER block air inlet (rear) or air outlet (front).
NEVER use duct work in front or rear of heater.
NEVER move or handle heater while still hot.
NEVER transport heater with fuel in tank.
NEVER use with an external fuel tank.
Keep all combustible materials away from this heater.
Minimum Clearance From Combustibles
MH-80TBOA-KFA
Top 4 ft. (122 cm)
Sides 4 ft. (122 cm)
Front 8 ft. (244 cm)
ALWAYS locate heater on a stable and level surface.
If your heater is equipped with a thermostat, once it
is plugged in, it can start at anytime in accordance
with the thermostat setting.
Do not add fuel when the heater is running.
Heater should be re-started within 24 hours of
operation.
RISK OF BURNS,
FIRE AND
EXPLOSION!
RISK OF ELECTRIC
SHOCK!
WARNING
WARNING
CAUTION! HOT
WHILE IN OP-
ERATION. DO
NOT TOUCH. KEEP CHILDREN, ANIMALS,
CLOTHING AND COMBUSTIBLES AWAY
FROM HEATER.
WARNING
The products described in this manual are
kerosene direct-fired, forced air heaters. Kerosene
forced air heaters are primarily intended for use for
temporary heating of buildings under construction,
alteration or repair. Direct-fired means that all
of the combustion products of the heater enter
the heated space. This appliance is rated at 98%
combustion eciency, but does produce small
amounts of carbon monoxide.
Carbon monoxide is toxic. Humans can tolerate
only small amounts of carbon monoxide and so
precautions should be taken to provide proper
ventilation. Failure to provide proper ventilation
in accordance with the instructions in this
manual can result in death.People with breathing
problems should consult a physician before
using this heater. Early signs of carbon monoxide
poisoning resemble the flu. Symptoms of improper
ventilation/carbon monoxide poisoning are:
Headache • Dizziness •Nausea • Dry Mouth Sore
Throat •Burning of Nose and Eyes
If you experience any of these symptoms:
GET FRESH AIR AT ONCE! Have your heater
serviced and check for proper ventilation. Some
people are more aected by carbon monoxide
than others. These include: pregnant women, those
with heart or lung problems, anemia or those under
the influence of alcohol or at high altitudes.
NOT FOR USE WHERE EXPOSED TO THE
WEATHER, INDOOR USE PERMITTED ONLY FOR:
The temporary heating of adequately ventilated
buildings or structures under construction,
alteration or repair. Provide at least a three
square foot (2,800 sq cm) opening of outside air
for every 100,000 Btu/Hr (29 kW) heater rating.
Refer to “Ventilation” on page 6 for further
instructions.
RISK OF INDOOR
AIR POLLUTION!
WARNING
CARBON
MONOXIDE
POISONING MAY
LEAD TO DEATH!
DANGER

4
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
SPECIFICATIONS
Model # MH-80TBOA-KFA
Rating: Btu/Hr / kW 80,000 / 23.4
Fuel Consumption: Gal/Hr / L/Hr 0.63 / 2.38
Fuel Tank Capacity: Gallons / Liters 5 / 19
Pump Pressure: psi / BAR 120 / 8.27
Volts: AC/Hz 120VAC / 60Hz
Amps 5
Heating Area: ft22000
Max. Operating Hours 8
Battery Voltage 18VDC Nominal
Battery Amps. 5
Specifications subject to change without notice.
FEATURES ASSEMBLY
Hot Air Outlet
Upper Shell
Handle
Fan Guard
Fuel Gauge
Fuel Cap
Power Cord
Fuel Tank
Power/Reset Switch
Thermostat Knob
Digital Readout
Battery (Not Included)
Lamp
Lower Shell
WHAT’S IN THE BOX MH80TBOAKFA
Carry Handle (1)
15 mm Screws (2) Heater (1)
- Remove the heater and all packaging materials
from the shipping carton Note: Save the box and packaging materials for future storage.
1. Install handle with two 15mm Philips screw
on upper shell

5
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
Fueling The Heater:
Kerosene (K-1)
For optimal performance of this heater, it is
strongly suggested that K-1 kerosene be used,
especially in temperatures lower than 26°F
(-3°C). K-1 kerosene has been refined to virtually
eliminate contaminants, such as sulfur, which can
cause a rotten egg odor during the operation of
the heater. Using diesel fuel can cause excess
soot production. Do not use Bio-Diesel as this fuel
will damage your heater’s seals and filter.
CSA certified for use with only No. 1 K kerosene
fuel. Factory Tested: Kerosene, Diesel #1 and
#2, Fuel oil #1 and #2, JP8 (Jet A fuel).
DO NOT use any fuel that is not approved above.
- NEVER use fuel such as, benzene, alcohol, white
gas, camp stove fuel, paint thinners, or other oil
compounds in this heater. THESE ARE VOLATILE
FUELS THAT CAN CAUSE A FIRE OR EXPLOSION.
- NEVER store kerosene in the living space. Kerosene
should be stored in a well ventilated area outside
the living area.
- NEVER store kerosene in direct sunlight or near a
source of heat.
- NEVER use kerosene that has been stored from one
season to the next. Kerosene deteriorates over time.
OLD KEROSENE WILL NOT BURN PROPERLY IN
THIS HEATER.
NOTE: Kerosene should only be stored in a blue
container that is clearly marked “Kerosene.” Never
store kerosene in a red container. Red is associated
with gasoline.
Ventilation:
- Risk of indoor air pollution and Carbon Monoxide
Poisoning. Use heater only in well ventilated
areas.
- Refer to Safety Information on page 3 for
information about Carbon Monoxide Poisoning.
- ALWAYS provide a fresh air opening in the heated
space of at least three square feet (2,800 sq. cm) for
each 100,000 Btu / Hr. (29 kW) of heater output.
Provide a larger opening if more heaters are being
used.
Minimum Ventilation Opening Needed
MH-80TBOA-KFA
2.4 ft.²
2230 cm²
OPERATION
NEVER FILL THE
FUEL TANK IN-
DOORS. ALWAYS
FILL THE TANK OUTDOORS. BE SURE THAT
THE HEATER IS ON LEVEL GROUND WHEN
FUELING, AND NEVER OVERFILL THE
TANK.
CAUTION
CARBON MONOXIDE POISONING MAY LEAD
TO DEATH!
DANGER
DO NOT USE GAS-
OLINE OR CRANK-
CASE DRAININGS.
WARNING
NEVER REFUEL
THIS HEATER
WHILE IT IS HOT
OR OPERATING. FIRE OR EXPLOSION
COULD RESULT.
DANGER

6
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
OPERATION CONT.
Pre-Lighting Instructions:
Charge the Battery
Ensure battery is fully charged for best run time. Follow
battery manufactures instructions for use, charging and
storing. Heater does not charge the battery.
Over Discharge Protection
Heater has a built in battery protection circuit that will
shut the heater o to protect the battery from over
discharging.
Starting the Heater: (Ignition)
1. Fill the tank with kerosene or other approved
fuel until needle on fuel gauge points to “F”.
2. Replace fuel cap and tighten firmly.
3. Connect the heater to power source, either
approved battery or a three prong (grounded)
power source. You must use a three prong
(grounded) extension cord that is at least 6 feet
long and is a minimum of 14 AWG rating.
4. Turn thermostat control knob to desired
temperature setting.
5. Move the power switch to the “On” position. The
power indicator light will illuminate and heater
will ignite.
NOTE: On first ignition or after refueling, you may hear a
grinding sound just before ignition. This is the fuel pump
removing the air from the fuel line. Your heater will start
up within seconds. If it does not start repeat start-up pro-
cedures with fuel gauge reading at least 1/2 tank.
NOTE: Smoking may occur on first ignition.
NOTE: The electrical components of these heaters are
protected by a fuse mounted in the PC board. If the
heater fails to ignite, check this fuse first and replace if
necessary. Also check the power source to be sure the
proper voltage is being provided to the heater.
Stopping the Heater (Cool Down):
Turn the power switch to the “O” position. Combustion
will stop and the Cooling Cycle will begin and last
approx. 5 mins. When the Cooling Cycle is complete
the fan will stop running and it will be safe to unplug the
heater or disconnect the battery.
NOTE: Unplugging the heater or disconnecting the bat-
tery before the Cooling Cycle has been completed may
cause overheating, possible damage to the heater and
heat plate.
Restarting the Heater:
1. Wait ten seconds after Cooling Cycle has been
completed.
2. Follow all ignition procedures.
Long Term Storage:
Use an approved siphon to drain fuel through the
fuel cap opening.
IMPORTANT: Never store leftover kerosene or diesel
between seasons, using old fuel can damage heater.
DO NOT disconnect heater from power source before
cooling cycle has been completed.
TIP: If the heater does not ignite; move
switch to “O” position, check steps 1-3
above and then move switch to “On” position.
TIP: If the heater does not ignite, the
thermostat may be set too low. Turn the
control knob to a higher setting until the
heater ignites. If the heater does not ignite; move
switch to “Off” position, check steps 1-5 above
and then move switch to “On” position.
Use only Master
approved batteries
—CONTACT YOUR
LOCAL SERVICE CENTER OR CALL 800-641-6996
FOR MORE INFORMATION
CAUTION
RISK OF FIRE! Never
transport heater with
battery attached
DANGER
RISK OF FIRE! REMOVE BATTERY FROM
HEATER WHEN NOT IN USE
DANGER

7
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
WARNING: Battery requirements: The
batteries (Lithium-ion Battery Packs) used with
this machine must be certied products that
comply with local safety regulations.
WARNING: Charger requirements: Please
use only the charger specied by the battery
manufacturer for charging. Charging with
another battery pack may cause a re hazard.
WARNING: Do not ignite or overheat the
battery or equipment, it may cause an explosion
if it catches re or is higher than the battery’s
required limit temperature.
WARNING: It is strictly prohibited to use
damaged or illegally modied batteries for this
machine as a power source, which may cause
re, explosion, personal injury, property damage
and other hazards.
NOTE:
1. This product will not charge the battery.
Please remove the battery after using the
product. If you do not use it for a long time,
you need to charge the battery regularly to
avoid affecting the battery life.
2. If the existing battery cannot be installed with
the device, please check Local after-sales
solution.
BATTERY OPERATION INSTRUCTIONS
Adapter Part Number ASM-00040 ASM-00040 ASM-00038 ASM-00038 ASM-00039 ASM-00071
Manufacturer DEWALT®Milwaukee®BLACK+DECKER®Porter Cable®Makita®Mastercraft®
Model 20V Max. & FlexVolt, 18V M18 20V Max. 20V Max. 18V 20V Max.
Technical Spec. (AH) 4-12 4-12 4-12 4-12 4-12 4-12
Battery Watt/hr 80-240 72-216 80-240 80-240 72-216 80-240
Battery Models
DCB080, DCB200, DCB201,
DCB203BT, DCB203G, DCB204,
DCB204BT, DCB205, DCB8205G,
DCB206, DCB207, DCB208,
DCB210, DCB230, DCB240,
DCB404, DCB406, DCB609,
DCB612
48-11-1815, 48-11-1820,
48-11-1828, 48-11-1835,
48-11-1840, 48-11-1845,
48-11-1850, 48-11-1860,
48-11-1865, 48-11-1860,
48-11-1890, 48-11-1812
LBXR36, LBX1540,
LBXR2036,
LBX2040, LBX2540
PCC685,
PCC685L
BL1815N,
BL1820B,
BL1830,
BL1830B,
BL1840B,
BL1850B,
BL1860B
054-3124-0
054-7553-4
054-7557-6
Battery Certication UL UL UL UL UL UL
Battery Charger Models DCB1106, DCB1112 48-59-1811, 48-59-1810,
48-59-1802 BDCA202
PCC690L,
PCC691L,
PCC692L,
PCC695L,
PCC699L
DC18RC,
DC18RA,
DC18SD
054-3126-6
Battery Charger Certication UL UL UL UL UL UL
NOTE: Actual run time may vary due to battery condition and ambient temperature.
DEWALT®, Milwaukee®, BLACK+DECKER®, Porter Cable®, Makita®, and Mastercraft® are registered trademarks of their respective owners. Pinnacle Climate Technologies, Inc.
is not associated, afliated, licensed, or endorsed by DEWALT®, Milwaukee®, BLACK+DECKER®, Porter Cable®, Makita®, and Mastercraft®.
Figure 1 Figure 2
Battery Run Time Estimated
Battery Voltage 18/20
Battery Pack Amp Hour 4 5 6 8 9 12
Estimated Run Time (Hour) 1.7 2.1 2.6 3.4 3.9 5.1
If you intend to use a Milwaukee® battery you will have to
replace the battery connection terminals.
1. Make sure heater is not plugged into a power source.
2. Locate terminals within the battery connection port. (See
Figure 1)
3. Using a Phillips screwdriver, unscrew the screws
holding in current terminals by turning the screws
counterclockwise.
4. Replace terminals with terminals provided in the bag.
(See Figure 2)
5. Be sure to tighten screws to ensure a good connection.

8
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
MAINTENANCE
Service:
DO NOT TAMPER WITH THE UNIT. HAVE
A COMPETENT SERVICEMAN MAKE ANY
NECESSARY ADJUSTMENT OR REPAIRS.
Use only original equipment parts. The use of
alternate or third party components can cause unsafe
operating conditions and will void your warranty.
We suggest following a maintenance schedule as
follows:
FUEL / FUEL TANK:
Flush tank every 200 hours of operation or as needed.
DO NOT flush with water; use fresh K-1 kerosene only.
NOTE: Use of diesel fuel may require additional
maintenance
FAN BLADES:
Blades should be cleaned at least once per heating
season, depending on conditions. Remove all
accumulated dust and dirt with a damp cloth, taking
care not to bend any of the fan blades. Be sure the
blades are dry before re-starting the heater.
FUEL FILTER:
The fuel filter should be cleaned at least twice
per heating season. Clean the filter by rinsing it in
clean K-1 Kerosene. Contaminated fuel could make
cleaning the fuel filter necessary immediately.
NOTE: To remove the filter from KFA turn filter 90º
counterclockwise. See Figure 3.
THERMISTER PLACEMENT:
Ensure the thermister wire is in the proper place.
The wire should be lying on the bottom shell inside
the heater with the plastic end placed under the
motor support/motor and away from fan blade.
Never service heater
while it is plugged in
or hot!
WARNING
Figure 3
Fuel Filter
Fuel Line
Side Cover

9
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
Service (Continued):
SPARK PLUG:
Clean and re-gap every 600 hours of operation, or
replace as needed. After removing the spark plug,
clean the terminals with a wire brush. Re-gap the
terminals to 0.140” (3.5mm). See Figure 5.
PHOTOCELL:
The photocell should be cleaned using a cotton
swab dipped in alcohol or water at least once per
heating season, or more depending on conditions.
See Figure 6.
PUMP PRESSURE:
While heater is operating, turn adjusting screw
clockwise to increase, counter-clockwise to
decrease pressure. Correct pump pressure is as
follows:
Model Number Pump Pressure
MH-80TBOA-KFA 120 PSI (8.27 BAR)
Tolerance ± 10%
NOZZLES:
Nozzles should be cleaned or replaced at least once
per heating season. Contaminated fuel could make
this necessary immediately. To clean dirt from nozzle,
blow compressed air through nozzle front. It may
be necessary to soak the nozzle in K-1 kerosene to
loosen any dirt particles. See Figure 7.
MAINTENANCE CONT.
Figure 5
Spark Plug
Burner Body
Figure 6
Photocell
Figure 7 Diusion Cap
Diusion Cap
Gasket
Burner Head
Gasket
Burner Blade
Burner Body
Blower
Assembly Nozzle

10
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2023 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
WIRING DIAGRAMS
Wiring Diagram / Diagrama eléctrico
MAKB-073
80TBOA-KFA Wiring Diagram EN+SP
75 x 65 mm
1
2 2
3
389
9
10
10
11 12 13
3
45 5
67
7
BK
BK
WT
(WT)
(WT) (WT)
(WT)
(BL)
ON/OFF
(RD)
(BL)
(RD)
(BL)
(WT)
BK
WT
RD
BK
RD
GN
1. AC 120V
2. Battery
3. 12V Fan
4. Spark
5. Ignition
6. Adaptor 18V 5A
7. DC
8. Thermostat
9. Pump
10. Valve
11. Temperature
Sensor
12. Photocell
13. Switch
BL. Blue
RD. Red
BK. Black
WT. White
GN. Green
BK
BK/BL
BK
BK BK BK BK BK BK
BK/BL
RD RD RD
1. CA120V
2. Batería
3. Ventilador de 12V
4. Bujía
5. Encendedor
6. Adaptador
de 18V 5A
7. Corriente
Continua
8. Termostato
9. Bomba
10. Válvula
11. Sensor de
Ambiente
12. Fotocélula
13. Interruptor
BL. Azul
RD. Rojo
BK. Negro
WT. Blanco
GN. Verde
MH-80TBOA-KFA
1. AC 120V
2. Battery
3. 12V Fan
4. Spark
5. Ignition
6. Adaptor 18V 5A
7. DC
8. Thermostat
9. Pump
10. Valve
11. Temperature Sensor
12. Photocell
13. Switch
BL. Blue
RD. Red
BK. Black
WT. White
GN. Green