Matatakitoyo Torque Tools MTD6-NS User manual

BEFORE STARTING
CONTENTS
HOW TO SET TORQUE VALUE
Pull to unlock and turn it to set the target torque.
Then push it back to lock.
1 2 3
Set LockUnlock
Body color : Black, Red, Blue or Green
Body Graduation Scale
Driver 6.35mm Main Scale Knob
TORQUE
6.35
For example, ITEM NO. MTD6-1405NS target torque is 3.5 Nm.
Red line of main scale reach 3 Nm (see A) and adjust
graduation scale to 0.5 Nm (see B), Then 3+0.5=3.5 Nm (see C)
Manual
WARNING
A B C
1. Study this instruction before use.
2. This torque wrench as calibrated and tested before leaving the factory is certified to meet the current standard
specification and has an accuracy of ±6%.
3. THIS TOOL IS A PRECISION MEASUREMENT AND DESIGNED FOR MANUAL TIGHTENING FASTERNERS ONLY.
DO NOT USE IT AS A NUT BREAKER OR FOR ANY OTHER PURPOSE.
4. Over torque will cause tool damage and personal injury.
5. Do not use this tool near rotating machinery.
6. Disassemble this tool or make any adjustments will result of losing accuracy and void the warranty.
7. Do not continuously apply force after hear click or feel shock.
8. Do not use any format of extension on the handle of the tool. This will not only damage the tool, also affect the accuracy.
9. Use special care at minimum torque setting.
10. Please wear gloves and goggles when working.
Torque screwdriver
Above MTD6-1405NS & 1450IS with
sliding T-Handle for more convenient use.
Manual
Supplied in a plastic box.
Only MTD6-1402NS & 1420IS
in a limpid box.
OPERATION MANUAL
Adjustable Torque Screwdriver
MTD6-NS
Models covered

E-mail:[email protected]om
www.matatakitoyo.com
Made in Taiwan
MATATAKITOYO TOOL CO., LTD.
No. 63, Ln. 493, Sec. 3, Zhongshan Rd., Tanzi Dist.,
Taichung City 42754, Taiwan
TEL : [phone]
Manufacturer Apr. 2020
02
Edition
1. When applying torque the screwdriver must be kept perpendicular to the plane of use (either horizontal or vertical).
2. Inaccuracies in torque readings may occur from applying “Side Load”.
90°
MAINTENANCE AND STORAGE
CONVERSION TABLE
Units to be
converted
1 mN.m
1 cN.m
1 N.m
1 ozf.in
1 lbf.in
1 lbf.ft
1 gf.cm
1 kgf.cm(kp.cm)
1 kgf.m(kp.m)
1
10
1000
7.062
113
1356
0.098
98.07
9807
0.1
1
100
0.706
11.3
135.6
0.01
9.807
980.7
0.001
0.01
1
0.007
0.113
1.356
0.0001
0.098
9.807
0.142
1.416
141.6
1
16
192
0.014
13.89
1389
0.009
0.088
8.851
0.0625
1
12
0.0009
0.868
86.8
0.0007
0.007
0.738
0.005
0.083
1
0.00007
0.072
7.233
10.2
102
10197
72
1152.1
13826
1
1000
100000
0.01
0.102
10.2
0.072
1.152
13.83
0.001
1
100
0.0001
0.001
0.102
0.0007
0.0115
0.138
0.00001
0.01
1
=mN.m =cN.m =N.m =ozf.in =lbf.in =lbf.ft =gf.cm =kgf.cm
(kp.cm)
=kgf.m
(kp.m)
Corresponding unit
Conversion-formula : Units to be converted × Factor = Corresponding unit
Example : Convert 5 lbf.ft into cN.m
Solution : 5 × 135.6 = 678 cN.m
1. Please return torque value to just below lowest reading when not in use. Do not turn below lowest reading. (see D)
2. If this tool has not been used for a period of time, it shall be preloaded several times at its
maximum torque setting. This will allow internal lubricant to recoat.
3. Clean this tool by wiping with a clean cloth after operation and storage in a dry environment.
Do not dip any type of liquid in this tool. This may damage the internal of this tool.
4. This tool should be recalibrated a period of 12 months, or 5,000 cycles, whichever occurs first.
To contact with local vendor, an authorized repair center for supporting. 1 Years
5000 Times
MetricSAE
Accuracy : ± 6%
Unit : mm
STOP
CLICK
L
ØD
A
SPECIFICATION
D
MTD6-1402NS
MTD6-1405NS
MTD6-1408NS
MTD6-1410NS
LA ØD
140
160
160
160
10
10
10
10
24
33
33
33
0.4-2 Nm
1-5 Nm
2-8 Nm
2-10 Nm
6.35
6.35
6.35
6.35
0.1 Nm
0.1 Nm
0.1 Nm
0.2 Nm
0.128
0.128
0.282
0.300
KG LA ØD
140
160
160
160
10
10
10
10
24
33
33
33
6.35
6.35
6.35
6.35
0.1 Nm
0.1 Nm
0.1 Nm
0.2 Nm
0.128
0.128
0.282
0.300
KG
4-20 in.lb
10-50 in.lb
10-80 in.lb
20-100 in.lb
MTD6-1420IS
MTD6-1450IS
MTD6-1480IS
MTD6-14100IS
ITEM NO. Range ITEM NO. Range