Matrix Cosec Argo F0I212 User manual

COSEC ARGO
Quick Installation Guide
COSEC ARGO FOE212/FOM212/FOI212
2
Please read this guide first for correct installation and
retain it for future reference. The information in this guide
has been authenticated at the time of publication.
However, Matrix Comsec reserves the right to make
changes in product design and specifications without
prior notice.
Know Your COSEC ARGO 3
8
Preparation For Installation
23
Connecting The Cables
What Your Package Contains 7
COSEC ARGO Variants 7
Technical Specification 9
Installation Instruction - Wall Mounting
11
Installation Instruction - Flush Mounting 17
Assigning IP Address and Other Network Settings 7

Card Sensing
Area
Touch Screen
Display
Finger Sensor
Mounting
Screw Hole
Figure 1: Front View
Figure 2:
Bottom View
Knock Out Area
Know Your COSEC ARGO
Back Plate or
Wall Mounting Plate
Figure 3: Rear View
34
Flush Mounting Plate

2
Next
Level
5. Do not install the device in outdoor areas which may be exposed
to rain, cold and dust. You can do indoor installation or on the turnstile
under the roof as shown in Figure5.
Figure 5
Figure 6
1. Do not install the device in extremely hot temperature or under direct
Sunlight on turnstile or at extra bright places. This may affect the LCD
and finger print sensor of device. You can do indoor installation or on the
turnstile under the roof as shown in Figure4.
2. You can mount the device on a flat surface such as a wall or Elevator,
close to the access point (door) with surface wiring or concealed wiring
as shown in Figure6.
3. Recommended height from ground level is upto 4.5 feet.
4. Do not install on unstable surfaces, near volatile inflammable materials,
areas where volatile gas is created, where ferromagnetic field or noise is
induced, where static is created, such as desks made of plastics, carpets.
Figure 4
Pre-Installation Safety Instruction
56

ŸCOSEC ARGO Unit
ŸFlush Mounting Plate
Ÿ4 Screws M5/25
Ÿ4 Screw Grips
ŸOverswing Diode
ŸPower Adaptor 12VDC,2A
ŸPower Supply Cable (with DC Jack)
ŸEM Lock Cable
ŸExternal Reader Cable
ŸFlush Mounting Template
There are three different variants of COSEC ARGO depends upon the RFID
Card inserted in it.
COSEC ARGO Variants: FOE 212, FOM 212 and FOI 212
What your Package contains
COSEC ARGO Variants
Default Username: Admin
Default Password: 1234
ŸOpen the Web browser in your computer.
ŸEnter the IP address of the COSEC ARGO (default: http://192.168.50.1)
in the address bar of the browser and press the Enter key on your
computer keyboard.
ŸWhen prompted, enter the login credentials for the Door.
Assigning IP Address and Other Network Settings
Before Wall mounting and Flush mounting of COSEC ARGO; follow the
below steps.
ŸRemove the mounting screw from mounting screw hole from the
bottom of device as shown in Figure2. The screw will be required
to fix the device at the end of Wall mounting or Flush mounting.
ŸSlide the back plate downwards to unlock the device from the
mounting hook and then remove it by pulling it outwards. This back
plate will be required as Wall mounting plate for Wall mounting of
COSEC ARGO. For details see Installation Instructions for Wall
Mounting.
ŸThe flush mounting plate is available in the package. This plate
will be required for flush mounting of COSEC ARGO. For details
see Installation Instructions for Flush Mounting.
Wall Mounting: Select a location. It must be a flat surface such as wall,
close to the access point (door).
Flush mounting: Select a wooden door, or a location where the duct
can be made. The rectangular duct of has to made in the wooden doorsize
in which Flush mounting plate will be installed.
For Concealed wiring in Wall mounting/Flush mounting, first draw out
the sufficient length of the cables from the hole of the mounting plate.
For Non-concealed wiring in Wall mounting; the knock -out area
has to be removed from outside by pressing on the bottom duct as shown
in Figure2.
The connection of EM Lock must be done using the diode for Back
EMF protection.
Preparation for Installation
78

Specification COSEC ARGO
FOE212
Technical Specification
COSEC ARGO
FOM212
COSEC ARGO
FOI212
Credential
Support
Event Buffer
Input Power
Reader Power
Output
Reader Interface
Type
Door Lock
Relay
Door Lock
Power
Built In PoE
Display
Card, Pin and Finger
5,00,000
12V DC @2A and PoE
RS 232 and Wiegand
Max 30V DC @2A
PoE (IEEE 802.3 af)
3.5 inch Capacitive IPS touch screen
with Gorilla glass 3.0;
Resolution: 480x320 pixels (HVGA)
910
Max 12V DC @0.250 A
Internal 12V DC @0.5A in PoE supply
mode and 12V DC @1A in adapter
Specification COSEC ARGO
FOE212
COSEC ARGO
FOM212
COSEC ARGO
FOI212
User
Capacity
Communication
Port
RF Option
(Card)
EM Prox
Mifare,
Desfire and
NFC
HID I Class,
HID Prox,
EM Prox,
Desfire, NFC &
Mifare
50,000
Operating
Temperature
Dimensions
(H x W x D)
Weight
Ethernet and WiFi
Yes
0 °C to +50 °C
186mm x 74mm x 50mm (Wall Mount)
186mm x 74mm x 16mm (Flush Mount)
0.650 Kg (Product Only)
1.3 Kg (Product with Accessories)
Thermal Sensor
Built In
Bluetooth
Yes (IEEE 802.11 b/g/n)
Yes
Built In WiFi

Drill the screw holes along the traced markings.
Fix Wall Mounting plate with the supplied screws.
Tighten the screws with screw driver.
Step 1
Place the Wall Mounting plate and trace screw
holes 1 and 2 on the wall where the device is to
be installed.
1
2
Installation Instruction - Wall Mounting
11
Step 2
12

ŸKeep all the cables parallel to the side of the COSEC
ARGO body in such a way that it should not cover the
back of the body as illustrated in below figure.
ŸRadially curved all the cables and lead it through the
duct of wall mounting plate to fit the wall mounting
plate easily with COSEC ARGO.
13 14
Connect the cables of the ARGO unit and lead all the cables
through the duct of the Wall mounting plate into the electrical
box recessed in the wall i.e. concealed wiring or through
the bottom of the device in non-concealed wiring.
Step 3
Duct for Concealed
Wiring
Cable
Connectors
Knock Out Area
for Non-Concealed Wiring
Mounting
Slots

Mounting
Screw
Step 5
Insert the mounting screw into the mounting screw
hole at the bottom of the device. Tighten the screw to
complete the Wall mounting.
15 16
Step 4
Align COSEC ARGO on the mounting plate and hook
into the mounting slot. Press the bottom side inwards
to lock it in place.

Place and fix Flush Mounting plate with the supplied screws.
Tighten the screws with screw driver.
Step 2
Figure 7
17 18
Installation Instruction - Flush Mounting
Step 1
ŸPlace the Flush Mounting Template on the desired
installation surface.
ŸMark the area along the dotted line and trace the
four screw holes (say A,B,C,D) on the wall as
shown in Figure7.
ŸNow drill the dotted line area and four screw
holes (say A,B,C,D) on the wall as illustrated in
Figure8. Flush Mounting
Plate
A
B
C
D
Flush Mounting
Template
Figure 8
A
B
CD

20
Cable
Connectors
Connect the cables of the ARGO unit and lead all the cables
through the flush mounting plate into the electrical box
recessed in the wall.
Mounting
Slots
Mounting
Screw hole
Step 3
19
ŸKeep all the cables parallel to the side of the COSEC
ARGO body in such a way that it should not cover the
back of the body as illustrated in below figure.
ŸRadially curved all the cables and lead it through the
duct of flush mounting plate to fit the flush mounting
plate easily with COSEC ARGO.

21 22
Align COSEC ARGO on the mounting plate and hook into the
mounting slot. Press the bottom side inwards to lock it in
place.
Step 4
Mounting
Screw
Step 5
Insert the mounting screw into the mounting screw
hole at the bottom of the device. Tighten the screw to
complete the Flush mounting.

External Reader Cable
(8 Pin to 15 Pin connector)
Power
Cable
EM Lock Cable
1
2
3
4
5
6
7
8
CN3
9
10
LOCK RLY NO -Yellow
EXIT SWITCH
DOOR STATUS- White
GND- Black
GND- Black
GND LOCK- Black
LOCK RLY NC-Dark Blue
+12V LOCK- Red
-White
GND- Black
EM Lock
Diode
LOCK RLY COM -Light Brown
23
ŸFor Concealed wiring; first draw out sufficient length of the
cables from the hole you have cut on the mounting surface.
ŸMake the electrical connections of Power, External Reader
and EM Lock by connecting supplied cable assembly to the
20 pin connector on the back side of COSEC ARGO.
1
2
CN1
Power
GND- Black
+12VDC IN- Red
1
2
3
4
5
6
7
8
CN2
External Reader
DATA 0- Green
DATA 1- White
BEEPER- Yellow
GREEN LED- Orange
GND- Black
RS 232 RX- Pink
RS 232 TX- Grey
+12V RDR- Red
ŸConnect the Ethernet Cable to the LAN port.
ŸConnect the micro USB port to Printer or Broadband dongle
using micro USB cable extender as required.
Connecting the Cables
Micro USB
connector cable
Ethernet Cable
G
F
24

At the end of product life cycle; batteries, soldered
boards, metal components and plastic components must
be disposed through recyclers.
If you are unable to dispose-off the products or unable to
locate e-waste recyclers, you may return the products to
Matrix Return Material Authorization (RMA) department.
The product refered is covered by the waste Electrical
and Electronic Equipment (WEEE) directive and must be
disposed of in a responsible manner.
WEEE Directive 2002/96/EC
Disposal Of Product After End-Of-Life
25 26
+
-
EM
Lock
Reverse biased
Diode
Power
Diode connection for Back EMF Protection
Connect the Overswing diode in reverse biased condition
parallel to the EM Lock for a better contact lifetime and
to protect the Device from the Inductive kickback.
GND
Cathode
Anode

V.1, March ‘19
Head Office
394-GIDC, Makarpura, Vadodara - 390010, India
Ph: ([phone]
Email: Suppor[email protected]
Website: www.matrixaccesscontrol.com
MATRIX COMSEC
Copyright
All rights reserved. No part of this document may be
copied or reproduced in any form or by any means
without the prior written consent of Matrix Comsec.
Warranty
Limited Warranty. Valid only if primary protection is
provided, mains supply is within limit and protected, and
environment conditions are maintained within product
specifications. Complete warranty statement is available
on our website:
www.matrixaccesscontrol.com
27