Mattel HotWheels Workshop Airbrush Auto Design Combo... User manual

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING:

1107 8 9
42 3 5 6
BHT79-0920
CONTENTS ASSEMBLY AIRBRUSH – FREE HAND AIRBRUSH – SPRAY PATTERN
TO PLAY – STENCIL TOOLS MORE WAYS TO PLAY
PERFORMANCE TIPS
TO PLAY
WORKSHOP
INSTRUCTIONSTION
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
PROTECT PLAY SURFACES BEFORE USE.
PENS CONFORM TO ASTM D4236.
5+
service.mattel.com
BHT79-0920 29.225’’x8.27’’ 1C+1C
2.
1.
4.
3.
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 new “C” size (LR14) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when the
airbrush can no longer spray ink.
• When exposed to an electrostatic
source, the product may malfunction.
To resume normal operation, remove
and re-install the batteries.
SET UP
4.
4.
1. 1.
Remove cap and insert ink pen into airbrush until it clicks in.
2.
1.
2.
2.
3.
3.
5.
6.
5.
6.
A. Take time to adjust the nozzle until the sprayed ink is fine and even. If ink is
blotchy, it will smear and spoil your design.
B. While spraying, point nozzle straight down so it is perpendicular to the vehicle.
Apply a thin coat of ink with smooth, back and forth strokes.
C. For a deeper color, airbrush additional thin coats of ink onto the vehicle after
drying.
D. Keep nozzle clean by wiping down occasionally during use or when there is ink
build-up.
E. Always keep pens stored cap side down in holder.
This is a battery-operated product.
1 yer (00001-2908G8) is required
to be placed inside the packaging.
Load vehicle inside chamber and center on the platform.
Lift handle to raise vehicle.
Hold airbrush between half an inch and 1.5 inches away,
then pull trigger to spray.
Rotate platform to spray other sides.
Press handle down halfway to lower the platform.
Rotate switch to fan ( ) and dry for at least 30 seconds.
Rotate switch to OFF ( ).
Press handle down all the way to release vehicle.
©2014 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Relations 1-800-524-8697. Mattel U.K. Ltd.,
Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service -
1300 135 312. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Diimport & Diedarkan Oleh:
Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Malaysia.Tel:[phone],
Fax:[phone].
Rotate switch to select airbrush ( ).
Place a piece of paper (not included) under airbrush. Pull trigger
and spray ink between half an inch and 1.5 inches from paper.
a
b
a
b
a
b
NOTE: You must re-adjust the nozzle every time a new ink pen is loaded.
3. Adjust nozzle until sprayed ink is fine and even.
TO PREVENT INK FROM DRYING, RECAP PENS AFTER USE AND REPLACE IN HOLDER.
PENS MAY STAIN FABRICS AND OTHER SURFACES.
AVOID CONTACT WITH CARPET, CLOTHING, WALLS AND FURNITURE.
When finished spraying, rotate the platform so the
vehicle faces you.
NOT FOR USE WITH SOME HOT WHEELS® VEHICLES.
a
b
To create a new design, use a damp cloth
(not included) to wipe off the ink until
vehicle is clean.
Wipe the nozzle clean with a damp cloth.
To clean the inside of the stencil tool, use
a damp cloth or cotton swab (not included).
Wipe platform, spray patterns and stencil tool
clean with a damp cloth.
Connect to other Hot Wheels® sets (sold separately).
TO PLAY B - SPRAY PATTERN
a
b
a
b
SIDE VIEW
BACK VIEW
BACK VIEW
1
2
CLICK
a
b
b
a
ASSEMBLY
If little or no ink comes out,
turn dial slightly toward .
If ink foams at the tip,
turn dial slightly toward .
+
-
a
1. Attach spray pattern to frame as shown.
2.
Attach to platform with tabs facing down.
3.
Press frame down to bottom position for shorter vehicles.
Lift frame up to top position for taller vehicles.
4.
Load vehicle inside and center on the platform.
Lift handle to raise vehicle into the spray pattern.
a
b
a
b
5.
6.
Hold airbrush between half an inch and 1.5 inches away
and pull trigger to spray pattern onto vehicle.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to
dry vehicle.
1. Attach stencil tool to airbrush.
2.
Select a graphic and align with the nozzle.
3.
4.
Repeat steps 4-6 under AIRBRUSH – FREE HAND to dry vehicle.
Use stencil pieces to draw designs directly onto vehicles.
Press stencil tool flush against the vehicle. Pull and hold trigger for around 10 seconds to spray
graphic onto vehicle.
TO PLAY – DECAL SHEETS CLEAN UP – AIRBRUSH
CLEAN OFF COLOR REVEAL DECALS TO REDESIGN
B. INK PENS
A. AIRBRUSH A. COLOR REVEAL DECAL SHEETS
B. FOIL DECAL SHEET
1.
2. 3.
Peel off and apply color reveal panels onto each vehicle.
Flatten the panels with the
smoothing tool.
Add color reveal decals onto the panels to create your design.
1. To remove your design, rinse vehicle under
running water.
2. Let dry until design disappears and start again!
Drain, clean and dry all items thoroughly before storing.
Decorate your vehicles with foil decals for a shiny look!
NOTE: Foil decals do not work with Color Revealing Pen.
x10
x1
Ink Pens
Color Revealing Pen
COLOR REVEAL DECAL SHEET x 2 FOIL DECAL SHEET x 1
4.
Apply color revealing pen to decals to uncover awesome
graphics.
Only use pens that come with the toy.
Recap pens after use. NOT FOR USE WITH SOME HOT WHEELS®VEHICLES.
5.
Reveal whatever portion you want of the decals or panels to
customize your design!
AIRBRUSH AUTO DESIGN COMBO PACK
b
SIDE VIEW
CLICK
CHOKING HAZARD – Small parts.
Not for children under 3 years.
WARNING: