Maxtor DIAMONDMAX 60 User manual

DiamondMax®60
96147H8, 94610H6, 93073H4,
92305H3, 91536H2
All material contained herein Copyright © 2000 Maxtor Corporation.
MaxFax™ is a trademark of Maxtor Corporation. DiamondMax®, Maxtor®
and No Quibble Service®are registered trademarks of Maxtor Corporation.
Other brands or products are trademarks or registered trademarks of their
respective holders. Contents and specifications subject to change without
notice. All rights reserved.
Corporate Headquarters
510 Cottonwood Drive
Milpitas, California 95035
Tel: [phone]
Fax: [phone]
Research and Development Center
2190 Miller Drive
Longmont, Colorado 80501
Tel: [phone]
Fax: [phone]
Part #1478

Before You Begin
Thank you for your interest in the Maxtor DiamondMax®60 AT hard disk drives. This manual provides technical
information for OEM engineers and systems integrators regarding the installation and use of DiamondMax hard
drives. Drive repair should be performed only at an authorized repair center. For repair information, contact the
Maxtor Customer Service Center at 800-2MAXTOR or 408-922-2085.
Before unpacking the hard drive, please review Sections 1 through 4.
CAUTION
Maxtor DiamondMax 60 hard drives are precision products. Failure to
follow these precautions and guidelines outlined here may lead to
product failure, damage and invalidation of all warranties.
1BEFORE unpacking or handling a drive, take all proper electro-static discharge (ESD)
precautions, including personnel and equipment grounding. Stand-alone drives are
sensitive to ESD damage.
2BEFORE removing drives from their packing material, allow them to reach room
temperature.
3During handling, NEVER drop, jar, or bump a drive.
4Once a drive is removed from the Maxtor shipping container, IMMEDIATELY secure
the drive through its mounting holes within a chassis. Otherwise, store the drive on a
padded, grounded, antistatic surface.
5NEVER switch DC power onto the drive by plugging an electrically live DC source cable
into the drive's connector. NEVER connect a live bus to the drive's interface connector.
6ELECTRICAL GROUNDING - For proper operation, the drive must be securely fastened
to a device bay that provides a suitable electrical ground to the drive baseplate.
Please do not remove or cover up Maxtor factory-installed drive labels.
They contain information required should the drive ever need repair.

DIAMONDMAX 60 PRODUCT MANUAL
i
ContentsContents
ContentsContents
Contents
Section 1Section 1
Section 1Section 1
Section 1— IntroductionIntroduction
IntroductionIntroduction
Introduction
Maxtor Corporation 1 - 1
Products 1 - 1
Support 1 - 1
Manual Organization 1 - 1
Abbreviations 1 - 1
Conventions 1 - 2
Key Words 1 - 2
Numbering 1 - 2
Signal Conventions 1 - 2
Section 2Section 2
Section 2Section 2
Section 2 —Product DescriptionProduct Description
Product DescriptionProduct Description
Product Description
The DiamondMax®60
Product Features 2 - 2
Functional/Interface 2 - 2
Zone Density Recording 2 - 2
Read/Write Multiple Mode 2 - 2
UltraDMA - Mode 4 2 - 2
Multi-word DMA (EISA Type B) - Mode 2 2 - 2
Sector Address Translation 2 - 2
Logical Block Addressing 2 - 3
Defect Management Zone 2 - 3
On-the-Fly Hardware Error Correction Code (ECC) 2 - 3
Software ECC Correction 2 - 3
Automatic Head Park and Lock Operation 2 - 3
Cache Management 2 - 4
Buffer Segmentation 2 - 4
Read-Ahead Mode 2 - 4
Automatic Write Reallocation (AWR) 2 - 4
Write Cache Stacking 2 - 4
Major HDA Components 2 - 5
Drive Mechanism 2 - 5
Rotary Actuator 2 - 5
Read/Write Electronics 2 - 5
Read/Write Heads and Media 2 - 5
Air Filtration System 2 - 5
Microprocessor 2 - 5
Subsystem Configuration 2 - 6
Dual Drive Support 2 - 6
Cable Select Option 2 - 6
Jumper Location/Configuration 2 - 6
Cylinder Limitation 2 - 6

DIAMONDMAX 60 PRODUCT MANUAL
ii
Section 3Section 3
Section 3Section 3
Section 3 —ProductSpecificationsProductSpecifications
ProductSpecificationsProductSpecifications
ProductSpecifications
Models and Capacities 3 - 1
Drive Configuration 3 - 1
Performance Specifications 3 - 1
Physical Dimensions 3 - 2
Power Requirements 3 - 3
Power Mode Definitions 3 - 3
Spin-up 3 - 3
Seek 3 - 3
Read/Write 3 - 3
Idle 3 - 3
Standby 3 - 3
Sleep 3 - 3
EPA Energy Star Compliance 3 - 3
Environmental Limits 3 - 3
Shock and Vibration 3 - 4
Reliability Specifications 3 - 4
Annual Return Rate 3 - 4
Quality Acceptance Rate 3 - 4
Start/Stop Cycles 3 - 4
Data Reliability 3 - 4
Component Design Life 3 - 4
EMC/EMI 3 - 5
EMC Compliance 3 - 5
Canadian Emissions Statement 3 - 5
Safety Regulatory Compliance 3 - 5
Section 4Section 4
Section 4Section 4
Section 4— Handling and InstallationHandling and Installation
Handling and InstallationHandling and Installation
Handling and Installation
Hard Drive Handling Precautions 4 - 1
Electro-Static Discharge (ESD) 4 - 1
Unpacking and Inspection 4 - 2
Repacking 4 - 3
Physical Installation 4 - 3
Before You Begin 4 - 4
Please Read 4 - 4
Back up. Protect Your Existing Data 4 - 4
Tools for Installation 4 - 4
System Requirements 4 - 4
Operating System Requirements 4 - 4
Hook up 4 - 4
Boot the System with MaxBlast Plus Diskette 4 - 4
Configure the Drive Jumpers 4 - 4
Installaing 5.25-inch Mounting Brackets 4 - 4
Install Hard Drive in Device Bay 4 - 5
Attach Interface and Power Cables 4 - 5
Start up 4 - 5
Set up 4 - 5

DIAMONDMAX 60 PRODUCT MANUAL
iii
Section 5Section 5
Section 5Section 5
Section 5— AT Interface DescriptionAT Interface Description
AT Interface DescriptionAT Interface Description
AT Interface Description
Interface Connector 5 - 1
Pin Description Summary 5 - 1
Pin Description Table 5 - 2
PIO Timing 5 - 3
DMA Timing 5 - 4
Ultra DMA Timing Parameters 5 - 5
Section 6Section 6
Section 6Section 6
Section 6— Host Software InterfaceHost Software Interface
Host Software InterfaceHost Software Interface
Host Software Interface
Task File Registers 6 - 1
Data Register 6 - 1
Error Register 6 - 1
Features Register 6 - 1
Sector Count Register 6 - 2
Sector Number Register 6 - 2
Cylinder Number Registers 6 - 2
Device/Head Register 6 - 2
Status Register 6 - 2
Command Register 6 - 3
Read Commands 6 - 3
Write Commands 6 - 3
Mode Set/Check Commands 6 - 3
Power Mode Commands 6 - 3
Initialization Commands 6 - 3
Seek, Format, and Diagnostic Commands 6 - 3
S.M.A.R.T. Commands 6 - 3
Summary 6 - 4
Control Diagnostic Registers 6 - 5
Alternate Status Register 6 - 5
Device Control Register 6 - 5
Digital Input Register 6 - 5
Reset and Interrupt Handling 6 - 6
Section7Section7
Section7Section7
Section7—InterfaceCommandsInterfaceCommands
Interface CommandsInterface Commands
Interface Commands
Command Summary 7 - 1
Read Commands 7 - 2
Read Sector(s) 7 - 2
Read Verify Sector(s) 7 - 2
Read Sector Buffer 7 - 2
Read DMA 7 - 3
Read Multiple 7 - 3
Set Multiple 7 - 3
Write Commands 7 - 4
Write Sector(s) 7 - 4

DIAMONDMAX 60 PRODUCT MANUAL
iv
Write Verify Sector(s) 7 - 4
Write Sector Buffer 7 - 4
Write DMA 7 - 5
Write Multiple 7 - 5
Mode Set/Check Commands 7 - 6
Set Features Mode 7 - 6
Read Native Max Address 7 - 7
Set Max 7 - 7
Set Max Password 7 - 7
Set Max Lock 7 - 7
Set Max Unlock 7 - 7
Set Max Freeze Lock 7 - 7
Power Mode Commands 7 - 8
Standby Immediate 7 - 8
Idle Immediate 7 - 8
Standby 7 - 8
Idle 7 - 8
Check Power Mode 7 - 8
Set Sleep Mode 7 - 8
Default Power-on Condition 7 - 9
Initialization Commands 7 - 10
Identify Drive 7 - 10
Initialize Drive Parameters 7 - 13
Seek, Format, and Diagnostic Commands 7 - 14
S.M.A.R.T. Command Set 7 - 15
Section 8Section 8
Section 8Section 8
Section 8— Service and SupportService and Support
Service and SupportService and Support
Service and Support
Service Policy 8 - 1
No Quibble Service 8 - 1
Support 8 - 1
GlossaryGlossary
GlossaryGlossary
Glossary

DIAMONDMAX 60 PRODUCT MANUAL
v
FiguresFigures
FiguresFigures
Figures
Figure Title Page
2 - 1 PCBA Jumper Location and Configuration 2 - 6
3 - 1 Outline and Mounting Dimensions 3 - 2
4 - 1 Multi-pack Shipping Container 4 - 2
4 - 2 Single-pack Shipping Container (Option A) 4 - 3
4 - 3 Single-pack Shipping Container (Option B) 4 - 3
4 - 4 IDE Interface and Power Cabling Detail 4 - 5
5 - 1 Data Connector 5 - 1
5 - 2 PIO Data Transfer to/from Device 5 - 3
5 - 3 Multi-word DMA Data Transfer 5 - 4
5 - 4 Initiating an Ultra DMA Data In Burst 5 - 5
5 - 5 Sustained Ultra DMA Data In Burst 5 - 6
5 - 6 Host Pausing an Ultra DMA Data In Burst 5 - 6
5 - 7 Device Terminating an Ultra DMA Data In Burst 5 - 7
5 - 8 Host Terminating an Ultra DMA Data In Burst 5 - 7
5 - 9 Initiating an Ultra DMA Data Out Burst 5 - 8
5 - 10 Sustained Ultra DMA Data Out Burst 5 - 8
5 - 11 Device Pausing an Ultra DMA Data Out Burst 5 - 9
5 - 12 Host Terminating an Ultra DMA Data Out Burst 5 - 9
5 - 13 Device Terminating an Ultra DMA Data Out Burst 5 - 10

DIAMONDMAX 60 – INTRODUCTION
1 – 1
SECTION 1
Introduction
Maxtor Corporation
Maxtor Corporation has been providing high-quality computer storage products since 1982. Along the way,
we’ve seen many changes in data storage needs. Not long ago, only a handful of specific users needed more than
a couple hundred megabytes of storage. Today, downloading from the Internet and CD-ROMs, multimedia,
networking and advanced office applications are driving storage needs even higher. Even home PC applications
need capacities measured in gigabytes, not megabytes.
Products
Maxtor’s products meet demanding storage capacity requirements with room to spare. They feature proven
compatibility and reliability. While DiamondMax®60 is the latest addition to our legacy of high performance
5,400 RPM desktop and workstation hard drives, our DiamondMax®VL 30 series hard drives deliver industry-
leading capacity, reliability and value for entry-level systems and consumer electronics applications.
Support
No matter which capacity, all Maxtor hard drives are supported by our commitment to total customer
satisfaction and our No Quibble Service®guarantee. One call – or a visit to our home page on the Internet
(http://www.maxtor.com) – puts you in touch with either technical support or customer service. We’ll
provide you the information you need quickly, accurately and in the form you prefer – a fax, a downloaded
file or a conversation with a representative.
Manual Organization
This hard disk drive reference manual is organized in the following method:
❏Section 1 – Introduction
❏Section 2 – Description
❏Section 3 – Specifications
❏Section 4 – Installation
❏Section 5 – AT Interface
❏Section 6 – Host Software Interface
❏Section 7 – Interface Commands
❏Section 8 – Service and Support
❏Appendix – Glossary
Abbreviations
ABBRV DESCRIPTION ABBRV DESCRIPTION
ATA AT attachment MB megabyte
bpi bits per inch Mbits/sec megabits per second
CHS cylinder - head - sector MB/sec megabytes per second
db decibels MHz megahertz
dBA decibels, A weighted ms millisecond
DMA direct memory access MSB most significant bit
ECC error correction code mV millivolts
fci flux changes per inch ns nanoseconds
Gacceleration PIO programmed input/output
GB gigabyte RPM revolutions per minute
Hz hertz tpi tracks per inch
KB kilobyte UDMA ultra direct memory access
LBA logical block address(ing) µsec microsecond
LSB least significant bit Vvolts
mA milliamperes Wwatts

DIAMONDMAX 60 – INTRODUCTION
1 – 2
Conventions
If there is a conflict between text and tables, the table shall be accepted as being correct.
Key Words
The names of abbreviations, commands, fields and acronyms used as signal names are in all uppercase type
(e.g., IDENTIFY DRIVE). Fields containing only one bit are usually referred to as the “name” bit instead of
the “name” field.
Names of drive registers begin with a capital letter (e.g., Cylinder High register).
Numbering
Numbers that are not followed by a lowercase “b” or “h” are decimal values. Numbers that are followed by
a lowercase “b” (e.g., 01b) are binary values. Numbers that are followed by a lowercase “h” (e.g., 3Ah) are
hexadecimal values.
Signal Conventions
Signal names are shown in all uppercase type.
All signals are either high active or low active signals. A dash character (-) at the end of a signal name
indicates that the signal is low active. A low active signal is true when it is below ViL and is false when it is
above ViH. A signal without a dash at the end indicates that the signal is high active. A high active signal is
true when it is above ViH and is false when it is below ViL.
When a signal is asserted, it means the signal is driven by an active circuit to its true state.
When a signal is negated, it means the signal is driven by an active circuit to its false state.
When a signal is released, it means the signal is not actively driven to any state. Some signals have bias
circuitry that pull the signal to either a true or false state when no signal driver is actively asserting or negating
the signal. These instances are noted under the description of the signal.

PRODUCT DESCRIPTION
2 – 1
SECTION 2
Product Description
Maxtor DiamondMax®60 AT disk drives are 1-inch high, 3.5-inch diameter random access storage devices which
incorporate an on-board ATA-5/Ultra DMA 100 controller. High capacity is achieved by a balanced combination
of high areal recording density and the latest data encoding and servo techniques.
Maxtor's latest advancements in electronic packaging and integration methods have lowered the drive's power
consumption and increased its reliability. Advanced giant magneto-resistive read/write heads and a state-of-the-art
head/disk assembly - using an integrated motor/spindle design - allow up to four disks in a 3.5-inch package.
Exceptionally high data transfer rates, 5,400 RPM spin speed and < 9.0 ms access times make these performance
series disk drives especially well-suited to high-end desktop and server applications.
DiamondMax 60 Key Features
ANSI ATA-5 compliant PIO Mode 4 interface (Enhanced IDE)
Supports Ultra DMA Mode 4 for up to 100 MB/sec data transfers
2 MB buffer with multi-adaptive cache manager
5,400 RPM spin speed
< 9.0 ms seek time
Zone density and I.D.-less recording
Outstanding shock resistance at 250 Gs
High durability with 50K contact start/stop cycles
Advanced multi-burst on-the-fly Error Correction Code (ECC)
Extended data integrity with ECC protected data and fault tolerant servo synchronization fields
Supports EPA Energy Star Standards (Green PC Friendly) with ATA powering savings commands
Auto park and lock actuator mechanism
Low power consumption
S.M.A.R.T. Capability
Note: Maxtor defines one megabyte as 10
6
or one million bytes and one gigabyte as 10
9
or one billion bytes.

PRODUCT DESCRIPTION
2 – 2
Product Features
Functional / Interface
Maxtor DiamondMax 60 hard drives contain all necessary mechanical and electronic parts to interpret control
signals and commands from an AT-compatible host computer. See Section 3 Product Specifications, for complete
drive specifications.
Zone Density Recording
The disk capacity is increased with bit density management – common with Zone Density Recording. Each
disk surface is divided into 16 circumferential zones. All tracks within a given zone contain a constant
number of data sectors. The number of data sectors per track varies in different zones; the outermost zone
contains the largest number of data sectors and the innermost contains the fewest.
Read / Write Multiple Mode
This mode is implemented per ANSI ATA/ATAPI-5 specification. Read/Write Multiple allows the host to
transfer a set number of sectors without an interrupt request between them, reducing transfer process
overhead and improving host performance.
UltraDMA - Mode 4
Maxtor DiamondMax 60 hard drives fully comply with the new ANSI Ultra DMA protocol, which greatly
improves overall AT interface performance by significantly improving burst and sustained data throughput.
Multi-word DMA (EISA Type B) - Mode 2
Supports multi-word Direct Memory Access (DMA) EISA Type B mode transfers.
Sector Address Translation
All DiamondMax 60 drives feature a universal translate mode. In an AT/EISA-class system, the drive may be
configured to any specified combination of cylinders, heads and sectors (within the range of the drive's
formatted capacity). DiamondMax 60 drives power-up in a translate mode:
MODEL CYL HD SPT LZone WPcom MAX LBA CAPACITY
96147H8 119,108 16 63 (*) (*) 120,060,864 61,471 MB
94610H6 89,331 16 63 (*) (*) 90,045,648 46,103 MB
93073H4 59,554 16 63 (*) (*) 60,030,432 30,735 MB
92305H3 44,666 16 63 (*) (*) 45,023,328 23,051 MB
91536H2 29,777 16 63 (*) (*) 30,015,216 15,367 MB
(*) The fields LZone (Landing Zone) and WPcom (Write Pre-comp) are not used by the Maxtor hard drive
and the values may be either 0 or the values set by the BIOS. All capacities listed in the above table are based
on 106or one million bytes.
Logical Block Addressing
The Logical Block Address (LBA) mode can only be utilized in systems that support this form of translation. The
cylinder, head and sector geometry of the drive, as presented to the host, differs from the actual physical
geometry. The host AT computer may access a drive of set parameters: number of cylinders, heads and sectors
per track, plus cylinder, head and sector addresses. However, the drive can’t use these host parameters directly
because of zoned recording techniques. The drive translates the host parameters to a set of logical internal
addresses for data access.
The host drive geometry parameters are mapped into an LBA based on this formula:
LBA = (HSCA - 1) + HHDA x HSPT + HNHD x HSPT x HCYA (1)
= (HSCA - 1) + HSPT x (HHDA + HNHD x HCYA) (2)
where HSCA = Host Sector Address, HHDA = Host Head Address
HCYA = Host Cylinder Address, HNHD = Host Number of Heads
HSPT = Host Sectors per Track

PRODUCT DESCRIPTION
2 – 3
The LBA is checked for violating the drive capacity. If it does not, the LBA is converted to physical drive
cylinder, head and sector values. The physical address is then used to access or store the data on the disk and
for other drive related operations.
Defect Management Zone (DMZ)
Each drive model has a fixed number of spare sectors per drive, all of which are located at the end of the
drive. Upon detection of a bad sector that has been reassigned, the next sequential sector is used.
For example, if sector 3 is flagged, data that would have been stored there is “pushed down” and recorded
in sector 4. Sector 4 then effectively becomes sector 3, as sequential sectors are “pushed down” across the
entire drive. The first spare sector makes up for the loss of sector 3, and so maintains the sequential order of
data. This push down method assures maximum performance.
On-the-Fly Hardware Error Correction Code (ECC)
16 symbols, single burst, guaranteed
Software ECC Correction
24 symbols, single burst, guaranteed
Automatic Park and Lock Operation
Immediately following power down, dynamic braking of the spinning disks delays momentarily allowing the
read/write heads to move to an inner mechanical stop. A small fixed magnet holds the rotary actuator in
place as the disk spins down. The rotary actuator is released only when power is again applied.
Cache Management
Buffer Segmentation
The data buffer is organized into two segments: the data buffer and the micro controller scratch pad.
The data buffer is dynamically allocated for read and write data depending on the commands received.
A variable number of read and write buffers may exist at the same time.
Read-Ahead Mode
Normally, this mode is active. Following a read request, disk read-ahead begins on the first sector and
continues sequentially until the allocated buffer is full. If a read request is received during the read-ahead
operation, the buffer is examined to determine if the request is in the cache. If a cache hit occurs, read-
ahead mode continues without interruption and the host transfer begins immediately.
Automatic Write Reallocation (AWR)
This feature is part of the write cache and reduces the risk of data loss during deferred write operations. If a
disk error occurs during the disk write process, the disk task stops and the suspect sector is reallocated to a
pool of alternate sectors located at the end of the drive. Following reallocation, the disk write task continues
until it is complete.
Write Cache Stacking
Normally, this mode is active. Write cache mode accepts the host write data into the buffer until the buffer
is full or the host transfer is complete. A command complete interrupt is generated at the end of the transfer.
A disk write task begins to store the host data to disk. Host write commands continue to be accepted and
data transferred to the buffer until either the write command stack is full or the data buffer is full. The drive
may reorder write commands to optimize drive throughput.

PRODUCT DESCRIPTION
2 – 4
Major HDA Components
Drive Mechanism
A brush-less DC direct drive motor rotates the spindle at 5,400 RPM (±0.1%). The dynamically balanced
motor/spindle assembly ensures minimal mechanical run-out to the disks. A dynamic brake provides a fast
stop to the spindle motor upon power removal. The speed tolerance includes motor performance and motor
circuit tolerances.
Rotary Actuator
All DiamondMax 60 drives employ a rotary voice coil actuator which consists of a moving coil, an actuator
arm assembly and stationary magnets. The actuator moves on a low-mass, low-friction center shaft. The low
friction contributes to fast access times and low power consumption.
Read/Write Electronics
An integrated circuit mounted within the sealed head disk assembly (near the read/write heads) provides up
to eight head selection (depending on the model), read pre-amplification and write drive circuitry.
Read/Write Heads and Media
Low mass, low force giant magneto-resistive read/write heads record data on 3.5-inch diameter disks. Maxtor
uses a sputtered thin film medium on all disks for DiamondMax 60 drives.
Air Filtration System
All DiamondMax 60 drives are assembled in a Class 100 controlled environment. Over the life of the drive, a
0.1 micron filter and breather filter located within the sealed head disk assembly (HDA) maintain a clean
environment to the heads and disks. DiamondMax drives are designed to operate in a typical office
environment with minimum environmental control.
Microprocessor
The microprocessor controls the following functions for the drive electronics:
Command execution
Cache management
Data correction and error recovery
Diagnostic execution
Data sequencing
Head positioning (including error recovery)
Host interface
Index detection
Spin speed control
Seeks
Servo
S.M.A.R.T.

PRODUCT DESCRIPTION
2 – 5
JUMPER CONFIGURATION J50 J48 J46 J44 J42
Master/Slave
Only drive in single drive system*
Master drive in dual drive system*
Slave drive in dual drive system
C
C
O
Cable Select
Disabled*
Enabled O C
Cylinder Limitation
Disabled*
Enabled O C
Factory Reserved O
Factory Reserved O
Key * = Default C = Closed (jumper installed) O = Open (no jumper installed)
Figure 2-1
PCBA Jumper Location and Configuration
Cylinder Limitation Jumper Description
On some older BIOS', primarily those that auto-configure the disk drive, a hang may occur. The Cylinder
Limitation jumper reduces the capacity in the Identify Drive allowing large capacity drives to work with older
BIOS'. The capacity reported when J46 is closed will be as follows: drives less than or equal to 32GB will
report 2.1GB. Drives greater than 32GB will report 32GB.
Subsystem Configuration
Dual Drive Support
Two drives may be accessed via a common interface cable, using the same range of I/O addresses. The drives
are jumpered as device 0 or 1 (Master/Slave), and are selected by the drive select bit in the
Device/Head register of the task file.
All Task File registers are written in parallel to both drives. The interface processor on each drive decides
whether a command written to it should be executed; this depends on the type of command and which
drive is selected. Only the drive selected executes the command and activates the data bus in response to
host I/O reads; the drive not selected remains inactive.
A master/slave relationship exists between the two drives: device 0 is the master and device 1 the slave.
When J50 is closed (factory default, figure 2-1), the drive assumes the role of master; when open, the drive
acts as a slave. In single drive configurations, J50 must be closed.
Cable Select Option
CSEL (cable select) is an optional feature per ANSI ATA specification. Drives configured in a multiple drive
system are identified by CSEL’s value:
– If CSEL is grounded, then the drive address is 0.
– If CSEL is open, then the drive address is 1.
Jumper Location / Configuration
Darkened jumper pins indicate factory-installed (default) shunts.

PRODUCT SPECIFICATIONS
3 – 1
SECTION 3
Product Specifications
Models and Capacities
Performance Specifications
MODEL 96147H8 94610H6 93073H4 92305H3 91536H2
Integrated Interface ATA-5 / Ultra DMA
Encoding Method E2 PR4 RLL 16/17
Interleave 1:1
Servo System Embedded
Buffer Size / Type 2 MB SDRAM
Data Zones per Surface 16
Data Surfaces / Heads 86432
Number of Disks 43221
Areal Density 11.2 Gb / in2 max
Track Density 27,300 tpi
Recording Density 340 - 412 kbpi
Flux Density 361 - 418 kfci
Bytes per Sector / Block 512
Sectors per Track 373 - 662
Sectors per Drive 120,060,864 90,045,648 60,030,432 45,023,328 30,015,216
MODEL 96147H8 94610H6 93073H4 92305H3 91536H2
Seek Times (typical read)
Track-to-Track 1.0 ms
Average (performance) < 9.0 ms
Average (silent mode) 15 ms
Full Stroke < 20.0 ms
Average Latency 5.55 ms
Rotational Speed (±0.1%) 5,400 RPM
Controller Overhead < 0.3 ms
Data Transfer Rate
To/From Interface
(UltraDMA - M4)up to 100 MB/sec
To/From Interface
(PIO 4/Multi-word DMA M4)up to 16.7 MB/sec
To/From Media up to 40.8 MB/sec
Start Time (0 to Drive Ready)8.5 sec typical
Drive Configuration
MODEL 96147H8 94610H6 93073H4 92305H3 91536H2
Formatted Capacity (MB LBA Mode) 61,471 46,103 30,735 23,051 15,367
Maxtor defines one megabyte as 106or one million bytes and one gigabyte as 109or one billion bytes.

PRODUCT SPECIFICATIONS
3 – 2
Physical Dimensions (maximum)
Figure 3 - 1
Outline and Mounting Dimensions
PARAMETER STANDARD METRIC
Height 1.028 inches 26.1 millimeters
Length 5.787 inches 147 millimeters
Width 4.00 inches 101.6 millimeters
Weight 1.3 pounds 0.59 kilograms

PRODUCT SPECIFICATIONS
3 – 3
Power Requirements
Power Mode Definitions
Spin-up
The drive is spinning up following initial application of power and has not yet reached full speed.
Seek
A random access operation by the disk drive.
Read/Write
Data is being read from or written to the drive.
Idle
The drive is spinning, the actuator is parked and powered off and all other circuitry is powered on.
The drive is capable of responding to read commands within 40 ms.
Standby
The spin motor is not spinning. The drive will leave this mode upon receipt of a command that requires
disk access. The time-out value for this mode is programmable. The buffer is active to accept write data.
Sleep
This is the lowest power state – with the interface set to inactive. A software or hardware reset is required
to return the drive to the Standby state.
EPA Energy Star Compliance
Maxtor Corporation supports the goals of the U.S. Environmental Protection Agency’s Energy Star program
to reduce the electrical power consumption of computer equipment.
Environmental Limits
PARAMETER OPERATING NON-OPERATING/STORAGE
Temperature 5° C to 55° C low temperature (-40° C)
high temperature (71° C) per MIL-STD-810E, method
501.3, climatic category; hot-induced conditions.
Thermal Gradient 25° C per hour (maximum)
Relative Humidity 5% to 95% (non-condensing)
Wet Bulb 30° C (maximum)
Altitude -200 to 10,000 feet -200 to 40,000 feet
Acoustic Noise - Idle Mode
(per ISO 7779, 10 microphone, average
sound power)
3.1 bel, measured at 5k ft.
MODE 12V ± 10% 5V ± 5% POWER
Spin-up (peak) 1800 mA 490 mA
Seek (avg) 650 mA 550 mA 10.6 W
Read/Write (avg) 250 mA 550 mA 5.8 W
Idle (avg) 250 mA 500 mA 5.5 W
Standby (avg) 20 mA 280 mA 1.6 W
Sleep (avg) 20 mA 200 mA 1.0 W

PRODUCT SPECIFICATIONS
3 – 4
Reliability Specifications
Annual Return Rate
< 1.0% Annual Return Rate (ARR) indicates the average against products shipped.
ARR includes all reasons for returns (failures, handling damage, NDF), but
does not include inventory credit returns.
Quality Acceptance Rate
< 1,000 DPPM The quality acceptance rate indicates the percentage of Maxtor products
successfully installed by our customers, and/or the number of defective parts
per million (DPPM) encountered during the entire installation process.
Start/Stop Cycles
50,000 This indicates the average minimum cycles for reliable start/stop function.
Data Reliability
< 1 per 1014 bits read Data errors (non-recoverable). Average data error rate allowed with all error
recovery features activated.
Component Design Life
5 years (minimum) Component design life is defined as a.) the time period before identified
wear-out mechanisms impact the failure rate, or b.) the time period up to the
wear-out point when useful component life expires.
Shock and Vibration
PARAMETER OPERATING NON-OPERATING
Mechanical Shock 30 Gs, 2.0 ms, no errors 250 Gs, 2.0 ms, no damage
Rotational Shock 18,000 Rad/sec,0.5 - 1.0 ms, no damage
Random Vibration 10 - 45 Hz at 0.004 G2/Hz
48 - 62 Hz at 0.008 G2/Hz
65 - 300 Hz at 0.004 G2/Hz
301 - 500 Hz at 0.0006 G2/Hz
no errors
PSD:
10 Hz at .05 G2/Hz
20 Hz at .055 G2/Hz,
300 Hz at .05 G2/Hz
301 Hz at .0014 G2/Hz
500-760 Hz at .001 G2/Hz
877 Hz at .003 G2/Hz
1000-1570 Hz at .001 G2/Hz
2000 Hz at .0001 G2/Hz
Swept Sine Vibration
10 - 300 Hz 1 G (0 - peak) amplitude, .25 octave per minute

PRODUCT SPECIFICATIONS
3 – 5
EMC/EMI
Radiated Electromagnetic Field Emissions - EMC Compliance
The hard disk drive mechanism is designed as a subassembly for installation into a suitable enclosure and is
therefore not subject to Subpart J of Part 15 of FCC Rules (47CFR15) or the Canadian Department of
Communications Radio Interference Regulations. Although not required, the disk mechanism has been
tested within a suitable end-use product and found to comply with Class B limits of the FCC Rules and
Regulations of the Canadian Department of Communications.
The CE Marking indicates conformity with the European Union Low Voltage Directive (73/23/EEC) when
the disk mechanism is installed in a typical personal computer. Maxtor recommends that testing and analysis
for EMC compliance be performed with the disk mechanism installed within the user's end-use application.
Canadian Emissions Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set
out in the radio interference regulations of the Canadian department of communications.
Le present appareil numerique n'emet pas de bruit radioelectriques depassant les limites applicables aux
appareils numeriques de Class B prescrites dans le reglement sur le brouillage radioelectrique edicte par le
ministere des communications du Canada.
Safety Regulatory Compliance
All Maxtor hard drives comply with relevant product safety standards such as CE, CUL, TUV and UL rules and
regulations. As delivered, Maxtor hard drives are designed for system integration before they are used.

INSTALLATION
4 – 1
SECTION 4
Handling and Installation
Hard Drive Handling Precautions
◆If the handling precautions are not followed, damage to the hard drive may result - which may void the warranty.
◆During handling, NEVER drop, jar, or bump a drive. Handle the drive by its sides and avoid touching the printed circuit board
assembly (PCBA).
◆Hard drives are sensitive to electrostatic discharge (ESD) damage. Use proper ESD practices by grounding yourself and the
computer system the hard drive will be installed in.
◆Allow the hard drive to reach room temperature BEFORE installing it in your computer system.
◆NEVER switch DC power onto the drive by plugging an electrically live DC source cable into the drive's connector. NEVER
connect a live connector to the hard drive's IDE interface connector.
◆ELECTRICAL GROUNDING - For proper operation, the drive must be securely fastened to a device bay
that provides a suitable electrical ground to the drive baseplate.
Electro-Static Discharge (ESD)
To avoid some of the problems associated with ESD, Maxtor advises that anyone handling a disk drive use a
wrist strap with an attached wire connected to an earth ground. Failure to observe these precautions voids the
product warranty.
Manufacturers frequently experience “unsolved” component/hardware malfunctions often caused by ESD. To
reduce the incidence of ESD-related problems, Maxtor recommends that any electronics manufacturing plans
include a comprehensive ESD program, the basic elements and functions of which are outlined here:
ESD Program Element ESD Program Function
Management Institute and maintain
Chief coordinator Organize and enforce
Multi-department committee Evaluate and improve
Employee training Educate and inform
ESD program supplies typically include: wrist- and foot-worn grounding straps; counter-top and floor antistatic
matting; wrist strap testers; ESD video and training materials. Sources for such supplies include:
Static Control Systems – 3M Charleswater
225-4S, 3M Center 93 Border St.
St. Paul, MN 55144 West Newton, MA 02165-9990
Maxtor also offers a complete video training package, “Care and Handling of Maxtor Disk Drives.”
Contact your Maxtor representative for details.