MaxVac DUSTBLOCKER 500 User manual

DUSTBLOCKER
500
INSTRUCTIONINSTRUCTION
MANUALMANUAL
GEBRAUCHS-UNDGEBRAUCHS-UND
WARTUNGSANLEITUNGENWARTUNGSANLEITUNGEN
INSTRUCTIEHANDLEIDINGINSTRUCTIEHANDLEIDING
ISTRUZIONI PER L’USOISTRUZIONI PER L’USO
E LA MANUTENZIONEE LA MANUTENZIONE
INSTRUCTIONS D’UTILISATIONINSTRUCTIONS D’UTILISATION
ET D’ENTRETIENET D’ENTRETIEN
INSTRUCCIONES DE USOINSTRUCCIONES DE USO
Y MANTENIMIENTOY MANTENIMIENTO

NOTES

MAX-VAC.COMDB 500 3
Dustblocker
500
ENGLISH
DEUTSCH
NEDERLAND
FRANCAIS
ITALIANO
ESPANOL
4
12
20
28
36
44

MAX-VAC.COMDB 500
4
ENGLISH
INSTRUCTION
MANUAL
CAUTION
OPERATION
FILTER SYSTEMS
ACCESSORIES
TROUBLESHOOTING
WARRANTY
EU DECLARATION OF CONFORMITY
6
7
8
9
10
11
11

ENGLISH DEUTSCH NEDERLAND FRANÇAIS ESPAÑOLITALIANO
MAX-VAC.COMDB 500 5
Dear customer,
Thank you for choosing a Dustblocker made by MAXVAC.
The Dustblocker 500 from MAXVAC has been manufactured with the greatest
care, and we hope that you will be happy with the Dustblocker 500 you have
just purchased. However, if the Dustblocker 500 does not fully comply with your
expectations, please contact your supplier.
The MAXVAC brand was born in Switzerland to provide maximum performance
equipment to deal dust management and environmental cleaning solutions.
The MAXVAC team is passionate about providing the most environmentally
and ecologically acceptable cleaning solutions to promote clean and healthy
environments in the home town and workplace.
The Dustblocker 500 was specically designed for the industry.
We are committed to continuous effective improvement in the battle against ne
dust.
For more information on our range, please go to www.max-vac.com

MAX-VAC.COMDB 500
6
CAUTION
GENERAL
Dustblockers can only be used for ltering dry, non-explosive dust.
Dustblockers cannot be used in moist rooms or rooms where an explosion
hazard may exist.
MAXVAC cannot be held liable if the Dustblocker is used for other applications or
if the Dustblocker is not used in accordance with this manual.
Damaged cables that have been bent or torn, can be dangerous during use
of the device and must be replaced immediately in order to prevent personal
injuries.
In order to prevent personal injuries and property damages you must place the
device on a sturdy foundation, so that the Dustblocker 500 cannot fall over.
Make sure your ngers do not get stuck when opening and closing the machine.
In order to prevent a risk of explosion, you should not place the device in a room
that may contain explosive gasses.
These instructions are intended for the MAXVAC Dustblocker 500.
When removing the packaging, please check whether the Dustblocker 500 has
been damaged during transport.

ENGLISH DEUTSCH NEDERLAND FRANÇAIS ESPAÑOLITALIANO
MAX-VAC.COMDB 500 7
OPERATION
Switch the unit to the off position (0) before removing the plug from the socket.
If the switch is on sparks may be generated between the socket and the plug of
the device.
Prior to performing maintenance, rst remove the plug from the socket in order
to prevent electrical shock.
When replacing the pre lter or hepalter it is possible that dust is dispersed
that can be dangerous for people’s health. Therefore, users should wear safety
glasses, safety gloves and a respiration mask that comply with protection class
FFP3.
Do not drill through or break open the H14 HEPA lter.
The operating panel is at the side of
the Dustblocker and is identical for all
models.
At the top of the operating panel you
will see from left to right:
Red led with a warning signal (gives
a signal if the H14/G4 lter has to be
replaced) (1)
Red switch (position I-O) (2)
Connect the plug to the socket on the
front of the machine to start the device
(3).
3 1
2

MAX-VAC.COMDB 500
8
FILTERS AND FILTER
OPERATION
The Dustblocker 500 separates the dust in three phases:
During the rst phase, the front lter is used. The lter collects the larger dust
particles and protects the Pre and H13/14 hepalter.
The second phase is a Pre Filter which collects the ner particles and protects the
H13/14 hepalter.
During the third phase, the H13/14 hepalter is used. This lter will collect the dust
that is dangerous for people’s health and that is not visible to the naked eye.
The front lter which sits behind the metal mesh needs to be replaced on a
regular basis according to the contamination of the air in the environment. This will
lengthen the life of the Pre Filter and H13/14 lter.
At the front of your Dustblocker you will see a Pre Filter. If the machine is used
daily we recommend changing it twice a year. Of course this depends on the
contaimination of the air in the environment. If you regularly replace your Pre Filter
you will lengthen the life of the hepalter.
It is simple to change the lter by
removing the two lock pins at the sides
and pull the lter out. At the top of the
Pre Filter you will nd a label with the
item number (Compare this number
with the number on the old lter).
Make sure that you place the lter as
indicated on the label : Airow

ENGLISH DEUTSCH NEDERLAND FRANÇAIS ESPAÑOLITALIANO
MAX-VAC.COMDB 500 9
It is simple to change the lter by removing the two lock pins at the sides and pull
the lter out. At the top of the Pre Filter you will nd a label with the item number
(Compare this number with the number on the old lter). Make sure that you place
the lter as indicated on the label : Airow
The DB500 is provided with a lter indicator connected to a warning led that
measures the pressure drop in the lter. In case of a pressure drop that is too high,
the red led will light up and the hepalter must be replaced. If the Dustblocker is
used while the warning led lights up, this could affect the operation of the device.
REPLACEMENT FILTERS
If the H13/14 hepalter is exposed to water, this may shorten or
end the lter’s life span.
pre-lters and H13/14 hepalters cannot be cleaned and must
be replaced if they are saturated.
G4 Front Filter
G3 Pre-filter
H14 Main Filter
H13 Main Filter
MV-DBF-1010
MV-DBF-1011
MV-DBF-1012
MV-DBF-1013
1 x per week or when necessary
1 x per 3 months or when necessary.
1 x per year or when necessary.
1 x per year or when necessary.
DB 500 Item Nº Replacement

MAX-VAC.COMDB 500
10
TROUBLESHOOTING
Problems Causes Solutions
The blower does not
function.
The blower stops
immediately.
Red signal LED lights
The device blows out
dust
Abnormal noise
No power
Defective power cord.
Defective switches
Problem with power
supply
Filter blocked
Filter defect or
loose
Check that the power
socket is working
Replace Cable
Contact your technical
service centre
Check whether cable
is installed properly.
Check if there is
voltage at the socket.
Replace the lter
Adjust or replace lter
Have the device
checked