Maxxima MEP-81000WL User manual
with over current protection
Do not exceed 2.1A for each USB port.
Do not exceed 3.1A total for both USB ports.
Do not use the electronic appliances when the USB
ports are in auto shut-down for over current protection.
..
,,,,,11
Maxxima
"
10-Outlet
Workshop
Power
Centre
with
2
Port
use
Charger
and
LED
Worklight
FEATURES
O
3-in-1
design
includes
power
strip,
worklight,
and
USB
charger
f)
10
wide-spaced
grounded
outlets
E) 2
port
3.4A
total
USB
charger
0
Bright
LED
worklight
with
90°
rotation
Cl)
Lighted
On/Off
power
switch
and
light
switch
8
Phone
cradle
0
Durable
metal
housing
ELECTRICAL
SPECIFICATIONS
Voltage:
15A,
125VAC,
60Hz
Max
Load:
1875
Watts
USB
Chargers:
3.4A
total
output
LED
Lights:
500
total
lumens
Power
Cord:
1.2
m
(4
ft)
14/3
SJT
SAFETY
INSTRUCTIONS
1.
This
product
is
designed
for
indoor
use
only.
Do
not
use
in
wet
or
damp
areas
or
outdoors.
2.
Use
this
product
only
with
a
125
volt
AC
power
source.
Do
not
exceed
1875
watts
and/or
15
amps
maximum
load.
3.
This
unit
is
equipped
with
a
circuit
breaker.
If
the
circuit
breaker
"trips"
due
to
a
power
overload,
do
the
following:
•
Unplug
the
multi-outlet
strip
from
the
power
source.
•
Turn
the
power
switch
of
each
piece
of
connected
equipment
to
the
off
position.
•
Unplug
and
remove
all
equipment,
tools,
and
apparatus
connected
to
this
product.
•
Wait
a
few
minutes,
then
plug
the
multi-outlet
strip
back
into
the
power
source.
•
Reset
the
circuit
breaker
switch
by
changing
its
position
from
"OFF"
to
"RESET."
•
Plug
each
piece
of
equipment
back
into
the
multiple
outlet
power
strip
one
at
a
lime
taking
care
not
to
exceed
maximum
wattage
and
amperage
load.
4.
Before
each
use,
make
sure
that
the
power
cord
is
uncoiled
and
knot-free
when
in
use
to
avoid
potential
over-healing
of
the
cord
and
unit.
5.
Always
use
the
finger
grip
on
the
plug
to
remove
it
from
wall
receptacle.
Never
pull
the
plug
out
of
the
power
outlet
by
pulling
on
the
cord.
6.
Never
open
the
lights
or
housing.
There
are
no
user
serviceable
parts
inside
and
opening
either
renders
any
warranty
null
and
void.
7.
To
avoid
electrical
shock,
do
not
use
near
water
or
in
areas
where
water
may
accumulate.
Keep
power
strip
at
least
4.9
m
(16
ft)
from
pools
or
spas.
Keep
plugs
dry.
8.
These
are
high
performing
LED
bulbs.
Do
not
shine
directly
in
anyone's
eyes
or
your
own.
9.
Do
not
attempt
to
disassemble
the
power
strip
as
there
are
no
user-serviceable
components.
The
LED
bulb
is
not
designed
for
replacement.
In
case
the
LED
bulb
fails
to
work,
contact
a
qualified
electrician
for
further
inspection.
10.
Do
not
remove
the
ground
prong
or
otherwise
try
to
alter
the
plug.
If
the
provided
plug
will
not
fit
the
outlet
receptacle,
have
the
proper
outlet
receptacle
installed
by
a
qualified
electrician.
11.
Do
not
use
the
power
strip
ifthere
are
any
visible
signs
of
damage
to
the
housing
or
the
LED
lights,
cuts
or
frayed
areas
in
the
power
supply
cord
or
connection
of
the
cord
to
the
plug,
broken
blades
or
any
other
damage
that
could
be
deemed
a
safety
hazard.
12.
This
product
is
not
a
toy
and
is
not
intended
for
children.
It
is
for
adult
use
only.
13.
The
exterior
surface
of
the
unit
can
be
wiped
clean
with
a
soft,
clean
cloth.
Do
not
immerse
or
submerge
any
part
of
the
unit
in
water
or
any
other
solvent.
Never
use
solvents
or
cleaning
agents
containing
petroleum
(petrol,
kerosene,
oil),
paint
thinner,
turpentine,
alcohol,
or
ammonia.
Always
unplug
the
power
strip
and
allow
the
LED
lights
to
cool
down
prior
to
cleaning.
WARNING!
Failure
to
comply
with
the
following
rules
may
result
in
fire
or
other
damage
and/or
in
electric
shock,
exposure
to
excessive
ultraviolet
radiation
or
other
injury.
All
warranties
contained
herein
are
null
and
void
if
power
strip
is
used
in
violation
of
any
of
the
following
rules:
1.
For
INDOOR
USE
ONLY
2.
Do
not
plug
this
power
strip
into
receptacles
that
are
not
properly
grounded.
3.
Do
not
"daisy-chain"
power
strips
in
serial
fashion.
4.
Do
not
this
plug
power
strip
into
an
extension
cord.
5.
Do
not
plug
extension
cords
into
this
power
strip.
6.
Do
not
use
this
power
strip
in
conjunction
with
a
UPS
(uninterruptible
power
supply).
8-Outlet
Workshop Power Center
with 2 Port USB Charger
and LED Work Light
Model: MEP-81000WL
7.
Do
not
use
this
power
strip
with
three-to-two
prong
adapters.
8.
Do
not
plug
heaters
into
this
power
strip.
9.
Do
not
use
with
generators,
sump
pumps,
water-related
devices,
life
support
devices,
medical
devices,
cars
or
motorcycles,
golf-cart
battery
chargers,
or
aquariums.
10.
These
are
high-performing
LED
bulbs.
Do
not
shine
directly
into
anyone's
eyes
or
your
own.
FCC
REGULATORY
STATEMENT
WARNING:
Changes
or
modifications
to
this
unit
not
expressly
approved
by
the
party
responsible
for
compliance
could
void
the
user
authority
to
operate
the
equipment.
This
device
complies
with
part
15
of
the
FCC
rules.
Operation
is
subject
to
the
following
two
conditions:
1.
This
device
may
not
cause
harmful
interference,
and
2.
This
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
Notes:
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
B
digital
device,
pursuant
to
Part
15
of
the
FCC
Rules.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
in
a
residential
installation.
This
equipment
generates,
uses
and
can
radiate
radio
frequency
energy
and,
if
not
installed
and
used
in
accordance
with
the
instructions,
may
cause
harmful
interference
to
radio
communications.
However,
there
is
no
guarantee
that
interference
will
not
occur
in
a
particular
installation.
If
this
equipment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:
1.
Reorient
or
relocate
the
receiving
antenna.
2.
Increase
the
separation
between
the
equipment
and
receiver.
3.
Connect
the
equipment
into
an
outlet
on
a
circuit
different
from
that
to
which
the
receiver
is
connected.
4.
Consult
the
dealer
or
an
experienced
radio/TV
technician
for
help.
IC
REGULATORY
STATEMENT
Under
Industry
Canada
regulations,
this
radio
transmitter
may
only
operate
using
an
antenna
of
a
type
and
maximum
(or
lesser)
gain
approved
for
the
transmitter
by
Industry
Canada.
To
reduce
potential
radio
interference
to
other
users,
the
antenna
type
and
its
gain
should
be
so
chosen
that
the
equivalent
isotropically
radiated
power
(e.i.r.p.)
is
not
more
than
that
necessary
for
successful
communication.
This
device
complies
with
Industry
Canada
licence-exempt
RSS
standard(s).
Operation
is
subject
to
the
following
two
conditions:
(1)
this
device
may
not
cause
interference,
and
(2)
this
device
must
accept
any
interference,
including
interference
that
may
cause
undesired
operation
of
the
device.
INSTALLATION
Wall
Mounting:
For
mounting,
unscrew
and
remove
plastic
end
caps.
Discard
end
caps
after
removing.
1.
Create
a
mounting
template
by
placing
a
sheet
of
paper
over
the
back
of
the
unit
and
punching
holes
in
the
paper
where
the
mounting
holes
are
on
the
back
of
the
unit.
2.
Temporarily
secure
the
paper
template
(with
painter's
tape
or
other
method
that
will
not
harm
paint
or
wall
coverings)
to
the
area
where
the
unit
is
to
be
mounted.
3.
To
mount
the
power
strip,
secure
to
wall
using
anchors
(not
included)
rated
for
a
minimum
of
30
pounds.
4.
Test
the
strength
of
the
attachment
of
the
mounted
product
to
the
wall,
before
use,
to
ensure
stability.
INSTRUCTIONS (POWER STRIP, LED, USB)
Using
the
Outlets
1.
Ensure
the
red
lighted
Reset/Off
switch
is
in
the
off
position.
2.
Plug
device(s)
into
the
power
strip.
3.
Turn
the
power
strip
on,
using
the
Reset/Off
lighted
power
switch.(!)
4.
After
using
the
power
strip,
turn
the
lighted
power
switch
off.
Using
the
LED
Worklights
1.
Rotate
the
LED
to
the
desired
position.
2.
Turn
the
LED
worklights
on
using
the
Reset/Off
switch.~
()
;
~
'---
--3,,.---
Note:
Mount
the
10-outlet
power
strip
above
your
workbench
and
point
the
lights
down
to
provide
light
while
performing
tasks.
Using
the
USB
Ports*
1.
Connect
the
USB
charging
cable**
to
one
of
the
USB
ports
on
the
®
10-outlet
power
strip.
2.
Connect
the
other
end
of
the
USB
charging
cable**
to
the
portable
electronic
device
that
requires
charging.
*USB
charging
ports
may
not
charge
all
devices.
Some
devices
may
require
a
proprietary
USB
power
supply.
Charging
speeds
may
vary
by
product.
**USB
charging
cable
is
not
included.
Ensure
compatible
USB
charging
cable
is
used.
Refer
to
the
owner's
manual
of
your
portable
electronic
device
in
charging
instructions.
Maxxima
CONTACT US
866-MAXXIMA (629-9462)
www.maxximastyle.com
125 Cabot Court
Hauppauge, NY 11788
Popular Power Distribution Unit manuals by other brands
SMAR
SMAR IS400P User & installation manual
LEGRAND
LEGRAND Server Technology PRO3X Network Connection Setup Guide
Mennekes
Mennekes AMTRON Light installation instructions
Emerson
Emerson Liebert MicroPOD MP2-210K user manual
ABB
ABB Relion 670 series Communication protocol manual
Siemens
Siemens SIPROTEC 7SS522 V4.6 manual
