Mayline Medina Series User manual

Medina Series
Desk - Height Adjustable
CALL 1-800-822-8037 FOR ASSISTANCE
ASSEMBLY INSTRUCTIONS
Model No. MNDTHA72 / 63
P/N MNDTHA REV 2 7/18 www.mayline.com
TM

2
N
Wire Management
Tray
PARTS LIST MNDTHA
Name Part Qty. Spare
Qty
A
Spare
Qty
Qty.
PartName
1
81
B8
1
C8
1
E17 1
4
G
HB HB
Cam Lock
Cam Post
Cam Sticker
REALS102**
M6 x15mm
D8
8H
4
I
F
MNDTHAHB
1
HARDWARE
1
J
1
Wood Dowel
M6 x 33mm
Corner Bracket
Allen Wrench 5mm
Allen Wrench 4mm
1
4 x 16mm
**Denotes Color Code
Items with HB are in hardware box.
HB
HB
HB
HB
HB
HB
HB
HB

1
K
Qty.
PartName Name Part Qty.
Top w/ Frame
1
1
M
L
Modesty Panel
Fixed Panel
2
1O6
1
P
Q
Right Leg
Left Leg
PARTS LIST MNDTHA
PARTS LIST MNDHA
1
ABDBHAHB
HARDWARE
Leveler
HB
Items with HB are in hardware box.
Qty.
PartName Name Part Qty.

3
PARTS LIST Z549
NOTE: Carton Contents
①. MNDTHA72/ MNDTHA63 - Top, 2 Panels and 2 Wire Management
trays w/ hardware.
②. MNDHA - 2 Legs with levelers.
③. Z549 - Control Box, Controller, Power Cord w/ mounting hardware.
Power cord
R2
HB
S1
HB
1
U
1
W
HB
Control box
2
T
Controller
HB
5 x 20mm
1
1
4 x 14mm
Spare
Qty
Qty.
PartName
HB
Spare
Qty
Qty.
PartName
HB

4
1install the Levelers (O) into the Legs (P and Q).
IMPORTANT!
Review ALL instructions before beginning assembly. These
instructions are provided to avoid problems that may occur from
improper assembly or installation. Mayline and/or its distributor
are not responsible for failure resulting from improper assembly
or installation of this product. Moreover, all warranties are void
for failure to follow these assembly instructions.
O
P / Q

5
Insert Wood Dowels (D) and Cam Locks (A) into the Fixed Panel (M).
Install Cam Posts (C) into threaded inserts in Legs (P and Q).
Attach Fixed Panel (M) to Legs (P and Q) by turning Cam Locks (A). Attach Stickers (B)
over Cams (A).
2
3Place Top (K) upside down on a clean non-abrasive surface. Insert Wood Dowels (D) and
Cam Locks (A) into the Modesty Panel (L). Install Cam Posts (C) into the Top (K). Attach
Modesty Panel (L) to top by turning Cam Locks (A). Attach Stickers (B) over Cam Locks (A).
M
B
A
C
D
L
K
B
A
CD
P
Q

6
5Carefully rotate the Top (K) w/ Panel
and place on the Legs (P and Q).
Install the Control Box (S) to Top (K) using Screws (R). Install the Bracket (I) to the
Modesty Panel (L) and Top (K) using screws (E).
4
TWO PEOPLE REQUIRED
S
E
IL
K
R
P
Q

Install the Top (K) to the Legs (P and Q) by Screw (H) with Wrench (J); Screws pass
thru Frame into Actuator Housing on Legs. Install Memory Controller (W) in desired location
on front edge of top and fasten with Screws (T).
6
7
F
G
Uninstall the Frame Mounting Screws, Qty 2,
with Wrench (F). Install Wire Management
Tray (N) to Frame using Screws (G) and
Wrench (F). Re-install Frame Screws thru
Wire Management Tray.
N
TW
H
7

8
Connect Controller (W) into the correct port, and Motor Cables from Legs into Ports M1 and
M2, in Control Box (S). Connect Power Cord (U) into Control Box (S). Plug Power Cord (U)
into outlet and proceed with Controller Initialization on following page.
8
U
S
S
W
Motor Cables

Make sure no obstacles are in the desk's path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to accommodate
the change in height.
IMPORTANT: You must INITIALIZE the desk prior to first use.
Controller Initialization- Press and hold the Down button on the controller until the desk
reaches its lowest height, slightly raises, and stops. Release the down button, your desk
is now ready for use. (Following the "USER MANUALS" to use your desk)
TROUBLESHOOTING
If the table is not functioning properly it may need to be reset. Unplug the
power cord for 20 seconds. Plug the power cord back in and follow
the RESET procedures;
If the error message persists after the reset procedure, please contact your dealer;
If the height between the legs exceeds 1.5 inches, stop the reset procedure,
please contact your dealer;
9