Mayline ULEXBUR User manual

Item number: ULEXBUR / ULEXBLK
EXECUTIVE HI-BACK CHAIR
1. To Adjust Seat Height:
While seated, lean forward and reach under the right
side of the chair to find the handle. Lift the handle
and raise your body up slightly to allow the chair to
raise to the desired height. To lower the seat, lift the
handle while applying more weight downward on the
seat. The chair will descend until the handle is
released or the chair reaches the bottom position.
2. To Operate Tilt Lockout:
While seated, reach under the left side of the chair to
find the lockout bar. Slide the bar to the left (or to the
outside), all the way out allows the chair to tilt
backwards. To lock the chair in the vertical position,
sit upright and push the bar to the right (or the center
of the chair).
3. To Adjust Tension on The Tilt
Mechanism:
Reach under the front center of the chair, grasp the
round knob and turn counter - clockwise to make the
tilt mechanism firmer (stiffer). To loosen the tilt
mechanism, turn the knob clockwise until the desired
resistance is felt.
OPERATING INSTRUCTIONS
619 N. Commerce St, PO Box 728, Sheboygan, WI 53082-0728
www.mayline.com 800-822-8037 Fax [phone]

Item number: ULEXBUR / ULEXBLK
EXECUTIVE HI-BACK CHAIR
Item # Description Quantity Part #
1.
2.
3.
4.
5.
6A
6B.
7.
8.
9.
10.
11.
12.
13.
14.
H
Casters
5 Star Base
Telescoping Cover
Gas Lift
Seat Plate
Left Arm Support
Right Arm Support
Seat Cushion
Back Cushion
1-1/4” Black Screws
1-1/4” Colored Screws
3/4” Colored Screws
Left Arm Pad
Right Arm Pad
Wrench
Hardware Pack
5
1
1
1
1
1
1
1
1
4
8
6
1
1
1
1
11625
11624
11626
11708
11601
11660**
11660**
11638**
11637**
H
H
H
11622(blk)
11627(bur)
H
11602
A. Remove all parts from carton and separate them into part number groups as indicated in parts list.
B. To begin assembly, place 5 star base (2) upside down and insert casters (1) into bottom of base (2).
C. Turn base (2) right side up on the floor and insert gas lift (4) into center hole on base (2).
D. Place telescoping cover (3) over the gas lift (4) and rest it on the base (2).
E. Secure arm pads (12 & 13) to the arms (6A & 6B) by using 3/4” colored screws (11).
F. Use 1-1/4" colored screws (10) to fasten arms (6A & 6B) to the back of the back cushion (8). Do not tighten
screws completely.
G. Insert 1-1/4" colored screws (10) into arm holes attaching arms (6A & 6B) to the bottom of seat cushion (7).
Tighten all the screws for arms.
H. Attach seat plate (5) tothe bottom of seat cushion (7) (with front of seat plate facing front of seat cushion) by using
1-1/4" black screws (9) and tighten screws.
I. Place the assembled chair on top of gas lift (4) and press down until fully engaged.
J. Periodically (every 90 days) make sure that the screws are still fully tightened.
ATTENTION: Make certain all screws are fully tightened before using chair.
ASSEMBLY INSTRUC
TIONS
PART
S
LI
S
T