MBW M300DP Instruction Manual

M300DP L Series Expansion I/O Module – Installation / User Manual
36 Copyright 2016 MBW Technologies, LLC All Rights Reserved
P/N: MN10058-00
AIt
Email: [e-mail]
Phone: [phone] x340
www.mbwtech.com
MBW
Technologies , LLC
Installation / User Manual
M300DP
Expansion I/O Module
for MBW L Series Control Panels
M300DP Expansion I/O Module
with AutoStart

M300DP L Series Expansion I/O Module – Installation / User Manual
2Copyright 2016 MBW Technologies, LLC All Rights Reserved
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 35
MBW-Technologies, LLC (2 – Year) Limited Warranty
MBW Technologies, LLC (“MBW”) warrants its Electronic Module, Display
products, Electrical Cable and Electrical Connector products to be free from
defects in materials and workmanship for a period of two (2) years from the date
of shipment by MBW. Within this period, MBW will, at its sole option, repair or
replace any Electronic Module or Display that fails in normal use and is returned
to MBW (freight prepaid) within the warranty period. MBW is not responsible
for charges connected with the removal of such product or reinstallation of
replacement or repaired parts. This warranty does not cover failures due to abuse,
misuse, accident, faulty installation or unauthorized alteration or repairs.
THE EXPRESS WARRANTY SET FORTH ABOVE IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
Statements made by any person, including representatives of MBW, which are
inconsistent or in conflict with the terms of this Limited Warranty, shall not be
binding upon MBW unless reduced to writing and approved by an officer of
MBW.
IN NO EVENT SHALL MBW BE LIABLE FOR ANY INCIDENTAL,
SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER
RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THIS
PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not
allow the exclusion of incidental or consequential damages, so the above
limitation may not apply to you. MBW retains the exclusive right to repair or
replace the electronic module or display or offer a full refund of the purchase
price at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND
EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.
Warranty Return Procedure:
To obtain warranty service, contact MBW Technologies, LLC Technical Support
Department at [phone] x341 or email [email protected] to describe
problem and determine appropriate action.

M300DP L Series Expansion I/O Module – Installation / User Manual
34 Copyright 2016 MBW Technologies, LLC All Rights Reserved
Index
A/S Mode............................................12
Block Diagram....................................21
DI1 and DI2 Function...................10, 14
Enter Button..........................................7
Escape Button.......................................7
Factory Installation
External Connections ...................20
Recommended Order....................19
Field Installation
Connections from A/S to Engine
Connector ...............................32
Connections from A/S to Keyswitch
................................................31
Connections from A/S to Throttle
Switch.....................................31
Make External Connections .........32
Recommended Order....................29
I/O Mode...............................................9
Installation
Connections from A/S to Display 31
Main Menu............................................7
Menu Navigation
Auto Start......................................25
Mode Button .........................................7
Operation
A/S Failure Alert ..........................17
Activate DI1 or DI2......................16
Enable A/S....................................16
Keyswitch Position.......................16
Schematic............................................22
Specifications......................................23
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 3
Table of Contents
Quick Start Guide ....................................................................................................... 5
Powering the System .......................................................................................................... 6
Changing Data Displays ..................................................................................................... 6
MP300DP System Operation ................................................................................ 7
Menu Navigation .................................................................................................................. 7
M300DP Module Setup ...................................................................................................... 8
M300DP Modes ..................................................................................................................... 8
I/O Mode Operation .................................................................................................. 9
AI1 and AI2 Setup ................................................................................................................ 9
Speed 1 / Speed 2 RPM ...................................................................................................... 9
IO Status ................................................................................................................................ 11
Auto Start Operation ............................................................................................. 12
Analog Input Setup ........................................................................................................... 12
Start Retries ......................................................................................................................... 12
Start Delay(s) ...................................................................................................................... 12
Speed Settings .................................................................................................................... 13
Throttle Profile ................................................................................................................... 13
Digital Input Setup ............................................................................................................ 14
IO Status ................................................................................................................................ 15
Activating AutoStart ......................................................................................................... 15
Typical Auto Start Application .......................................................................... 18
Installing Control Panel with Expansion I/O .............................................. 19
Making the Connections ................................................................................................. 19
Engine Connector .............................................................................................................. 21
Wiring Diagram ....................................................................................................... 22
Technical Specifications ....................................................................................... 23
System Components .............................................................................................. 23
Default Settings ........................................................................................................ 24
Appendix A - Menu Overview ............................................................................ 25
Troubleshooting Guide ......................................................................................... 28
Appendix B – Field Installation ......................................................................... 29
Making the Connections ................................................................................................. 29
Connection Details ............................................................................................................ 33
Mechanical Mounting ...................................................................................................... 33
Updating Display Software............................................................................................ 33

M300DP L Series Expansion I/O Module – Installation / User Manual
4Copyright 2016 MBW Technologies, LLC All Rights Reserved
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 33
Connection Details
Connector Description
P4 6 Pin; connects to , black housing
S1 6 Pin; connects to P1r, grey housing
CAN Yellow & Green wires
Oil Pres, Fuel Analog Inputs - Orange, Green/Black wires
DI1 / DI2 Discrete Inputs - White/Black, White, Black
Common Common – connects to Throttle Switch, Black
Mechanical Mounting
The Auto Start module has two mounting holes 0.18 Diameter or # 8
screws. The mechanical dimensions are shown in the figure.
Updating Display Software
In order for the display to recognize the Auto
Start module, the display software must be
revision v2.00 or higher. Go to the System Menu
and scroll down to ABOUT M154. Hold MODE to
view the software version screen. When the Auto
Start module has been installed, the SW Version for the M300DP will also
be displayed.
If your software needs updating, contact your local distributor for the latest
software revision.

M300DP L Series Expansion I/O Module – Installation / User Manual
32 Copyright 2016 MBW Technologies, LLC All Rights Reserved
Insert Auto Start Leads into the Engine Connector
The Auto Start module provides six wire leads from the module to support
two analog inputs, two discrete inputs and an alarm. These leads must be
inserted into the P1 connector. The recommended pin locations are
shown in the table below.
Make External Connections
To connect the two analog signals and the two discrete inputs to the
device(s), five pigtails are provided and must be inserted into the Engine
harness. The recommended pin locations are shown in Table 4.
The installer is responsible for making the connection from each pigtail to
the device(s) (Oil Pressure Sender, Fuel Sender, Float Switch, etc.).
Figure 3. Engine Connector Pigtails
Alternate Connection
Although the installation instructions show the analog and discrete inputs
going to the 21 pin engine connector they could also be grouped together
on a separate 6 pin connector (DT04-6S).
Existing Engine Harness
Make connections to Senders
and Float Switch
Insert six Auto Start pigtails into
the engine connecto
r
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 5
Quick Start Guide
Navigation
Keypad
Throttle
Increment /
Decrement
Key Switch
RPM Gage
Controller
Display
10A Resettable
Circuit Breaker
System ICONS

M300DP L Series Expansion I/O Module – Installation / User Manual
6Copyright 2016 MBW Technologies, LLC All Rights Reserved
Powering the System
The M300DP Expansion I/O control module is a dual mode system and
can be programmed for either Auto Start (A/S) or expansion I/O capability.
The M300DP can be used with all M150B and M150L Series Control
Panels.
To power the system turn the key switch to the “ON” position. This will
activate the control panel and apply power to the M300DP module and the
engine ECU. Should the control panel indicate a fault condition review the
M150 Series manual for details and correct the condition before starting
the engine.
On a successful power up sequence, the system will display the currently
configured default display. The factory default display is Engine Speed.
Changing Data Displays
To change the data being displayed press the “▼” or “▲” buttons to
access additional data displays.
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 31
Connect the Auto Start Module to the Display
The following four steps provide the detailed modifications to the control
panel harness required for the Auto Start module.
1. Remove the wedgelock and the Yellow wire from the P3
connector and insert the Yellow wire from the Auto Start module
into the vacated pin location (Pin 3).
2. Remove the Green wire from the P3 connector and insert the
Green wire from the Auto Start module into the vacated pin
location (Pin 4).
3. Re-install the wedgelock and plug the P3 connector into the
display.
Connect the Auto Start Module to the Keyswitch
The following four steps provide the detailed modifications to the control
panel harness required for the Auto Start module.
1. Remove the P1 connector from the keyswitch and install the P4
connector of the Auto Start module into the keyswitch.
2. Remove the wedgelock and insert the Yellow wire removed from
the display connector into pin 6 of the P1 connector.
3. Insert the Green wire removed from the display connector into
pin 3 of the P1 connector.
4. Re-install the edgelock and plug the P1 connector into the S1
connector of the Auto Start module.
Connect the Auto Start Module to the Throttle Switch
The following steps provide the detailed modifications throttle switch.
1. Remove the black wire from the throttle switch and install the
black wire with 1/4 “ quick disconnect.
2. Re-install black throttle wire onto the piggyback terminal.
Figure 2. Throttle Switch Connection
Black throttle switch wire plugged
into piggyback terminal.

M300DP L Series Expansion I/O Module – Installation / User Manual
30 Copyright 2016 MBW Technologies, LLC All Rights Reserved
Re-Assemble
9. Mount the Auto Start module.
10. Connect the control panel connector (HDP24-21 connector) to the
engine harness.
11. Re-install the control panel.
12. Connect battery.
13. Turn ignition key to “ON” position.
14. Ensure digital display is active. If display is not active;
a. Check battery and power connections.
b. Check ignition switch is on position.
15. Ensure system is displaying data for engine speed, oil pressure
and temperature.
Figure 1. Expansion I/O Module
Insert Yellow wire into P3-3 &
Green wire into P3-4
S1
P4
Insert six wires into
engine connector
Connect Black wire to
throttle switch
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 7
MP300DP System Operation
Menu Navigation
The Mode Button is multi-functional and is used as an escape and enter
key. When the Mode key is pressed for less than 1 second it is considered
an escape action. When pressed for greater than 1 second is considered
an enter function. For example, to enter a menu selection or save an
entered value the button must be pressed and held for greater than 1
second. When escaping a menu selection, momentary Mode Button
presses are used. The only exception to these actions is entering the
main menu. From any runtime data display screen a momentary press of
the Mode Button will activate the main menu.
Main Menu
The Main Menu allows the user to access all areas of the M150L Control
System. To access the Main Menu press the Mode button. To access
menu items highlight the desired selection using the “▼” or “▲” keys and
press & hold the MODE for 1 second.

M300DP L Series Expansion I/O Module – Installation / User Manual
8Copyright 2016 MBW Technologies, LLC All Rights Reserved
M300DP Module Setup
To access the M300DP menu, press on the MODE
key to view the Main Menu. Press the “▼” or “▲”
keys until “M300DP Module” is highlighted. Press
and hold MODE > 1 second to enter the M300DP
submenu.
NOTE: The M300DP Module menu selection will only be visible if the
M300DP is correctly installed and has CANbus communication with the
M150L series display.
M300DP Modes
The M300DP has three modes which determine how the module operates
as well as the structure of the M300DP menu within the display.
OFF: AutoStart functionality is disabled.
Configurable digital inputs are disabled. The two
additional analog inputs are still available and are
a shared setting between all three modes.
I/O: Two configurable DI’s can be set as engine
stop, start, inhibit, or programmable speed
inputs. Analog inputs remain the same. No
autostart functionality.
A/S: Autostart mode uses the DI’s to
automatically start and stop the engine while key
switch is in the “Auto” position. A customizable
three speed throttle profile controls the engine
speed during startup and shutdown.
To view the current
M300DP Mode, press and
hold the MODE key > 1
second while the MODE
selection is highlighted. To
change the mode, use the “▼” or “▲” keys to highlight the desired mode.
Press and hold the mode key to save and confirm the change.
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 29
Appendix B – Field Installation
Making the Connections
The Expansion I/O Module shown in Figure 1, has two floating connectors
(P4 and S1), 6 wire leads to be connected to the Engine connector, one
black lead with a piggyback quick disconnect which goes to the throttle
and two leads (Yellow and Green) which go to the .
Also provided are six 6” pig tails (White w/Blue, Orange, Green w/Black,
White, White w/Black and Black) which can be used on the engine side of
the engine connector to make remote connections to analog and discrete
inputs.
Recommended order:
1. Verify the battery / battery switch connections to engine per the
engine installation diagram. (Refer to engine manufacturer
installation manual.). Verify engine is bonded to battery return (-).
Verify engine block is connected to battery ground.
2. Disconnect battery.
Control Panel Modifications
3. Loosen the four screws (3/32 Hex) and remove the control panel
from the housing base. Disconnect the control panel from the
engine harness (HDP24-21 connector).
4. Make connections from the Auto Start module to the display.
MORE DETAIL IN NEXT SECTION
5. Make connections from the Auto Start module to the keyswitch
6. Make a connection to the throttle switch
7. Insert the 6 wire leads from the Auto Start module into the 21 pin
engine connector (HDP24-21 connector).
Engine Harness Modifications
8. Make external connections to the Oil Pressure Sender, Fuel
Sender, Digital Input 1, Digital Input 2 and Common to the 21 pin
Deutsch connector of the engine harness using the five 6” pigtails.

M300DP L Series Expansion I/O Module – Installation / User Manual
28 Copyright 2016 MBW Technologies, LLC All Rights Reserved
Troubleshooting Guide
Symptom Action
The M300DP Menu Selection does not
show up in the Main Menus
Check the Yellow and Green wires from the
A/S Module and the Display
Check the keyswitch connection (Black
Wire)
Make sure the M150 Series software
version is version 2.0 or higher.
Engine does not crank when keyswitch is
in normal Start position
Check pin D (i.e., Start) connection to the
Engine Connector.
Engine cranks but does not fire when
keyswitch is in normal Start position
Check Engine manual for troubleshooting
start issues.
Auto Start ALERT not displayed when
keyswitch set to Auto Start (Full
Counterclockwise position) .
Check the settings to make sure the mode
is set to A/S
With a discrete input set to Start/Stop, the
Auto Start Alert screen is displayed but
turns off and then on again
Make sure the On Delay set for the discrete
input are longer than the time the discrete
input is bouncing.
Engine running but shuts down
unexpectedly; then restarts.
Make sure the Off Delay set for the discrete
input are longer than the time the discrete
input is bouncing.
The auto start countdown does not start
when the discrete input is activated
Make sure DI1 and DI2 are correctly set for
Start and Stop
Make sure the Active State for DI1 and DI2
are set correctly
Make sure the discrete input wires are
inserted into the correct pin locations of the
Engine Connector.
The data for the senders on to an analog
input does not show up as an Engine
parameter.
Make sure the analog input wires are
inserted into the correct pin locations of the
Engine Connector.
The data for the senders connected to an
analog input shows up on the Engine
display but the values are wrong
Make sure the sender selection for the
analog input are set to the correct sender
option (US versus Euro)
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 9
I/O Mode Operation
Input / Output Mode (I/O Mode)
Selecting I/O disables the Auto Start Feature but
allows the DI1 and DI2 inputs to be used as I/O.
The AI1 and AI2 analog inputs will be active.
AI1 and AI2 Setup
The M300DP Module has two analog inputs which may be configured for
a number of senders. When the analog sender has been connected and
the setup complete, the corresponding screen will be added to the rotating
display list.
Off
Fuel US (240-33 ohms)
Fuel Euro (10 – 180 ohms)
Water Level US (240-33 ohms)
Water Level Euro (10- 180 ohms)
Use the “▼” or “▲” keys to highlight the desired sender type. Press and
hold mode to save the selection or quick press mode to discard any
changes.
Speed 1 / Speed 2 RPM
The I/O Mode supports the setup of two different engine RPMs. These
speed settings are bounded by the MIN / MAX RPM in the Engine menu.
When a DI configured as Speed 1 or Speed 2 is activated the display will
command the engine to the configured RPM.
Use “▼” or “▲” keys to set Speed 1 RPM or Speed 2 RPM.

M300DP L Series Expansion I/O Module – Installation / User Manual
10 Copyright 2016 MBW Technologies, LLC All Rights Reserved
DI1 and DI2 Setup
The DI1 Setup and DI2 Setup are used to program the operation of the
two discrete inputs.
DI1 and DI2 Function
The DI1 or DI2 inputs are used to control the engine and may be
configured as Off, Stop, Speed1, Speed2 or Start Inhibit (Start Inh) as
defined in Table 1.
.
NOTE: When the DI1 and DI2 inputs are setup as speed inputs, DI2 has
priority over DI1 regardless of whether it has been configured to Speed 1
or Speed 2. The throttle switch has priority over both DI1 and DI2.
Table 1 - DI1 and DI2 Setup
Stop - When configured to Stop, DI1 or DI2 will stop the engine.
Speed 1 - When configured to Speed 1, DI1 or DI2 will ramp the
engine to the Speed 1 setting.
Speed 2 - When configured to Speed 2, DI1 or DI2 will ramp the
engine to the Speed 2 setting.
Start Inh - When configured to Start Inh (Start Inhibit), the engine will
not start while the configured DI is active.
OFF – Disables the discrete input
M300DP L Series Expansion I/O Module – Installation / User Manual
Copyright 2016 MBW Technologies, LLC All Rights Reserved 27
M300DP Main Menu – con’t