McIntosh C1000 User manual

C1000 Preamplifier Rear Panel Connections
2A
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: [phone] FAX: [phone] Part No. 04100200
MAIN RIGHT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times
MAIN/SPKR 1 and 2 RIGHT
Channel OUTPUTS (Balanced)
contain Listen signals and may be
assigned either as two additional
Main Outputs (active all the time)
or switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
PROCESSOR RIGHT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode
PROCESSOR RIGHT Channel RECORD
TO and FROM allows an external signal
processor to be connected for use in the
Record mode
CD (6), CDR (5)
and D/A (7) RIGHT
Channel INPUTS
(Balanced) accept
high level program
source signals
TUNER (3), DVD (1), SRVR (4)
and AUX (2), RIGHT Channel
INPUTS (un-balanced) accept
high level program source signals
PHONO INPUTS RIGHT MM
(8) accepts signals from a Moving
Magnet Phono Cartridge. MC (9)
Input accepts the low level signals
from a Moving Coil Phono Car-
tridge
SPKR 1 and 2 RIGHT Chan-
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
RECORD LINK INPUTS (Bal-
anced) connect to the Record Link
RIGHT Channel Input on the
C1000T Preamplifier when the
C1000P and a C1000T Preampli-
fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes
CDR (5) RIGHT
Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders
SRVR (4) and CDR (5)
RIGHT Channel OUPTUTS
(Unbalanced) contain the
selected Record Source Signal
for recorders
GND (Ground)
connectors for
connecting
the Turntable
Ground Wire
to the C1000P
Chassis
RECORD LINK INPUTS (Bal-
anced) connect to the Record
Link LEFT Channel Input on the
C1000T Preamplifier when the
C1000P and a C1000T Preampli-
fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes
CD (6), CDR (5) and
D/A (7) LEFT Chan-
nel INPUTS (Bal-
anced) accept high
level program source
signals
CDR (5) LEFT
Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders
MAIN LEFT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times
MAIN/SPKR 1 and 2 LEFT
Channel OUTPUTS (Bal-
anced) contain Listen signals
and may be assigned either as
two additional Main Out-
puts (active all the time) or
switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SPKR 1 and 2 LEFT Chan-
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SRVR (4) and CDR (5) LEFT
Channel OUPTUTS (Unbalanced)
contain the selected Record Source
Signal for recorders
PROCESSOR LEFT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode
PROCESSOR LEFT Channel RECORD
TO and FROM allow an external signal
processor to be connected for use in the
Record mode
TUNER (3), DVD (1), SRVR (4)
and AUX (2), LEFT Channel IN-
PUTS (un-balanced) accept high
level program source signals
PHONO INPUTS LEFT MM (8)
accepts signals from a Moving
Magnet Phono Cartridge. MC (9)
Input accepts the low level signals
from a Moving Coil Phono Car-
tridge
RIGHT PREAMPLIFIER
INPUT A Connector accepts
the custom McIntosh 21
Conductor Cable. This cable
connects to the C1000C
RIGHT CONTROLLER
OUTPUT A. It supplies the
control signals and power
supply voltages for the Right
Channel Circuitry in the
Preamplifier
LEFT PREAMPLIFIER
INPUT B Connector ac-
cepts the custom McIn-
tosh 21 Conductor Cable.
This cable connects to the
C1000C LEFT CONTROL-
LER OUTPUT B. It sup-
plies the control signals and
power supply voltages for
the Left Channel Circuitry
in the Preamplifier

C1000 Tube Preamplifier Rear Panel Connections
2B
MAIN RIGHT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times
MAIN/SPKR 1 and 2 RIGHT
Channel OUTPUTS (Bal-
anced) contain Listen signals
and may be assigned either as
two additional Main Out-
puts (active all the time) or
switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
PROCESSOR RIGHT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode
PROCESSOR RIGHT Channel RECORD
TO and FROM allow an external signal
processor to be connected for use in the
Record mode
CD (6), CDR (5)
and D/A (7) RIGHT
Channel INPUTS
(Balanced) accept
high level program
source signals
TUNER (3), DVD (1), SRVR (4)
and AUX (2), RIGHT Channel
INPUTS (un-balanced) accept
high level program source signals
PHONO INPUTS RIGHT MM
(8) accepts signals from a Mov-
ing Magnet Phono Cartridge. MC
(9) Input accepts the low level
signals from a Moving Coil Phono
Cartridge
SPKR 1 and 2 RIGHT Channel
OUTPUTS (unbalanced) contain
Listen signals and are switched
On/Off with the Remote Control
SPKR 1 and 2 Push-buttons
RECORD LINK INPUTS (Bal-
anced) connect to the Record
Link RIGHT Channel Input on
the C1000P Preamplifier when the
C1000T and a C1000P Preampli-
fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes
CDR (5) RIGHT
Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders
SRVR (4) and CDR (5) RIGHT
Channel OUPTUTS (Unbalanced)
contain the selected Record Source
Signal for recorders
GND (Ground)
connectors for
connecting
the Turntable
Ground Wire
to the C1000T
Chassis
RECORD LINK INPUTS (Bal-
anced) connects to the Record
Link LEFT Channel Input on the
C1000P Preamplifier when the
C1000T and a C1000P Preampli-
fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes
CD (6), CDR (5) and
D/A (7) LEFT Chan-
nel INPUTS (Bal-
anced) accept high
level program source
signals
CDR (5) LEFT
Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders
MAIN LEFT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times
MAIN/SPKR 1 and 2 LEFT
Channel OUTPUTS (Bal-
anced) contain Listen signals
and may be assigned either as
two additional Main Out-
puts (active all the time) or
switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SPKR 1 and 2 LEFT Chan-
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons
SRVR (4) and CDR (5) LEFT
Channel OUPTUTS (Unbalanced)
contains the selected Record
Source Signal for recorders
PROCESSOR LEFT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode
PROCESSOR LEFT Channel RECORD
TO and FROM allow an external signal
processor to be connected for use in the
Record mode
TUNER (3), DVD (1), SRVR (4)
and AUX (2), LEFT Channel IN-
PUTS (un-balanced) accept high
level program source signals
PHONO INPUTS LEFT MM (8)
accepts signals from a Moving
Magnet Phono Cartridge. MC
(9) Input accepts the low level
signals from a Moving Coil Phono
Cartridge
RIGHT PREAMPLIFIER
INPUT C INPUT
Connector accepts the cus-
tom McIntosh 21 Conductor
Cable. This cable connects
to the C1000C RIGHT
CONTROLLER OUTPUT
C. It supplies the control
signals and power supply
voltages for the Right Chan-
nel Circuitry in the Tube
Preamplifier
LEFT PREAMPLIFIER
INPUT D Connector ac-
cepts the custom McIn-
tosh 21 Conductor Cable.
This cable connects to the
C1000C LEFT CONTROL-
LER OUTPUT D. It sup-
plies the control signals and
power supply voltages for
the Left Channel Circuitry
in the Tube Preamplifier