MCOHome MH7-WH User manual

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 1
Water /Electrical Heating Thermostat
MH7-WH / MH7-EH
Introduction
MCOHome Water / Electrical Heating Thermostat is a Z-Wave enabled device for indoor
temperature control. MH7-WH is mainly applied to control wall mounted boiler, water
valve/pump etc. , while MH7-EH is for electrical heating system. The device is of high reliability
and practicability, which can be included and operated in any Z-Wave network with other Z-Wave
certified devices from any other manufacturers.
Features：
 Capacitive touch buttons
 Tempered glass panel, PC alloy enclosure
 Precise temperature calibration function
 Attractive appearance
 Clear display, easy to operate
Specification
 Power Supply：AC85-260V, 50/60HZ
 Output: MH7-WH ≤5A ; MH7-EH≤ 16A
 Self Consumption：≤1W
 Internal Temp. Sensor: NTC 15K
 External Temp. Sensor(optional): NTC R25℃=15KΩ B25℃/50℃=3550K
 Working Environment：0-50℃; 0-90% RH（Non-condensation)
 Temperature Setting：5-37 ℃（41-99℉）（Adjustable）
 Dimension：86* 86*15mm
 Hole Pitch：60-61mm
Safety Information
To protect yourself and others from danger and to protect the device from damage, please read the
safety information before using it.
Important!
 A qualified electrician with the understanding of wiring diagrams and knowledge of electrical
safety should complete installation following the instructions.
 Before installation, please confirm the real voltage complying with the device’s specification.
Cut off any power supply to secure the safety of people and device.
 During installation, protect the device from any physical damage by dropping or bumping. If
happens, please contact the supplier for maintenance.
 Keep the device away from acid-base and other corrosive solids, liquids, gases, to avoid
damage.

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 2
 Avoid overexertion during operation, to protect device from mechanical damage.
 Read all instructions and documentation and save for future reference.
Installation & Wiring
Location:
Thermostat is suggested to be installed indoor, a place with around 1.5m height above the
floor where represents the average room temperature. It should be away from direct sunlight, any
cover, or any heat source, to avoid false signal for temperature control.
CAUTION: Cut off power supply at circuit breaker or fuse before installation to avoid fire,
shock or death!
Step 1: Separate the device into two parts: the display
panel and the bottom.
Step 2: Insert all wires into the right terminals and
tighten screws. Wiring diagrams are shown below.
Step 3: Push the bottom into the junction box and
secure it with two screws, and then mount the touch
panel back.
Step 4: Confirm the device is well mounted, power on and it is ready to operate.
L
N
COM
NC
NO
L
N
Passive com
Normal open
Normal close
L
N
COM
L
N
Valve
NC
NO
T
T
T
T
Sensor Sensor
L
N
T
T
L
N
Elec
OUT
Sensor
（1)Passive Wall-boiler （2）Active normal close valve （3） Electrical Heating
Model Terminals Control
devices
Wiring
instructions
Contact
capacity
MH7-WH
N、L、COM、NO、
NC
Thermostatic
valve/electric
ball
valve/pump
For passive control,
follow wiring
diagram (1); For
active control,
follow wiring
diagram (2)
10A
MH7-EH N、L、OUT、T、
T
Heating film、
electric
radiator，
heating cable
ect
TT terminal is to be
connected with an
external sensor with
high temperature
protection function
16A

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 3
MH7-WH-WT15 N、L、COM、NO、
NC、T、T
Thermostatic
valve/electric
ball /pump
TT terminal is to be
connected with an
external ambient
temperature sensor
10A
MH7-EH-WT15 N、L、OUT、T、
T
Heating film、
electric
radiator，
heating cable
ect
TT terminal is to be
connected with an
external ambient
temperature sensor
16A
Button & Display
Operation
On/Off operation
When power on, thermostat displays “OFF”，all outputs are forced off. Touch S3 button to
switch (manual/off/auto) mode, then press S2 to confirm and proceed power on/off setting. After
power on, device displays current week, local time, working mode, current temperature, output
status etc.
Note:After the backlit goes out, please press the button to light up the backlit first, then press the
button again for corresponding operation.
Temperature setting
In normal working status, press S4 or S5 button will enter into temperature setting interface.
The setting range is 5-37 ℃（41-99℉）. Then press S4 or S5 can adjust the value. Press S3 or wait
25 seconds without any key operation will save the setting and return back to the normal operation
interface.
Auto Mode: The changed value only valid in the current time period for this time, and
the device will not effect the preset time period value .
Manual Mode: The changed value will be valid until next setting.
Vacation Mode: The changed value will be valid until next setting.

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 4
Key lock function
In normal operating interface, long press S1+S4 button, icon appear that indicates the
button is locked, at this time all buttons are disabled; When long press S1+S4 button again,
icon disappear that indicates the button is unlocked, all buttons back to normal work.
Control specifications
MH7-WH
 Detection temperature < setting temperature - 0.5℃, output turns on, and output icon
displays.
 Detection temperature ≥ setting temperature + 0.5℃, output turns off, and output icon
disappears.
MH7-EH
 Detection temperature < setting temperature - 1.5℃, output turns on, and output icon
displays.
 Detection temperature ≥ setting temperature , output turns off, and output icon
disappears.
Manual / Auto mode setting
In normal display interface, touch S3 button can switch between Manual and Auto mode.
Choose the mode you may need and press S2 button to save the setting.
Auto Mode: Device will follow the preset time periods and temperature to control heating
system automatically.
Manual Mode: Device will follow the manual setting temperature to control the heating
system.
Vacation mode setting
 In normal working interface, if vocation mode is not activated, long press S2 button to enter
vacation mode temperature setting. The default temperature is 10 , ℃and setting range is
5-37 ℃（41-98℉） . Press S4 or S5 to adjust the value, then press S3 or wait 25 seconds to save
the setting and return to the normal working interface. In this time vacation mode icon
displays, and device will follow the setting.
 Long press S2 again will end vacation mode and resume to normal work, vacation mode icon
will be disappeared.
Local Time Setting
 In normal working interface, long press S1 to enter into local time setting interface.
 In local time setting interface, press S4 or S5 button to set the “week, hour & minute”
parameter, and press S1 button can switch among the “week, hour & minute”.
 After finish the local time setting, press S1 or wait 25 seconds without any key operation will
save the setting and return to normal display.

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 5
Auto Mode Time Periods Parameter Setting
 In normal working interface, short press S1 to enter into time periods setting. Four time
periods can be set for each day of the whole week.
 Press S2 can switch among “Hours, Minutes, Temperature value”. Press S4 or S5 can change
the value.
 After finished the setting of 4 time periods on Monday, press S1 and follow the same way to
set periods of next days.
 After all periods set, press S1 /S2 or wait 25 seconds without any key operation will save the
setting and return to normal display. Device will operate in accordance with the new setting.
The default setting is as follow:
High temperature protection (For MH7-EH Electrical Heating ONLY)
When external temperature sensor detect the temperature value≥55℃, device will open high
temperature protection, electric heating will be forced off, and high temperature protection icon
displays.
When external temperature sensor detect the temperature value＜50 ℃, device will return to
normal work, high temperature protection icon disappears.
Anti-freeze protection function: (Optional)
In shutdown interface:
 When the built-in temperature sensor detect the temperature value≤5℃, device will open
anti-freeze protection, electric heating will be forced open, and anti-freeze protection icon
displays.
When the built-in temperature sensor detect the temperature value＞8 ℃, device will turn
off anti-freeze protection and return to normal work, anti-freeze icon disappears.
Note: If MH7 thermostat do not connect with an external temperature sensor, it will only display
the indoor temperature icon; If MH7 thermostat connect with an external temperature sensor, it
will display the indoor temperature and high temperature protection icon; When it is under high
temperature protection, high temperature protection icon flickers.
Z-Wave Operation
 Including & Excluding of Z-Wave network
In normal working interface, press & hold S4 to enter interface for inclusion or exclusion of
Z-Wave network. Before device included into network, “- - -” will display on the screen. Then
press S4 once, device will enter learning mode to get a node ID. If inclusion is success, a node ID
will display on the screen in a few seconds.
A node ID can always inform us whether the device is in the network or not.
Week\Periods
Period 1 Period 2 Period 3 Period 4
Mon~Fri 5:00 18℃ 7:00 16℃ 16:00 22℃ 21:00 16℃
Sat~Sun 6:00 18℃ 8:00 16℃ 16:00 22℃ 21:00 16℃

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 6
Note: Follow the same steps to exclude
the device from the network.
After inclusion, turn off the device and
then turn it on. Now the device is ready to be
operated by controller/ gateway in Z-Wave
network.
 Association Group
Thermostat supports 1 association group. A gateway is suggested to associate with this
group. Then if any changes happen, such as: temperature, working mode, etc., the thermostat
will report to this associated device (gateway).
 Command Class supported by the device:
COMMAND_CLASS_BASIC;
COMMAND_CLASS_THERMOSTAT_SETPOINT;
COMMAND_CLASS_THERMOSTAT_MODE;
COMMAND_CLASS_THERMOSTAT_OPERATING_STATE;
COMMAND_CLASS_SENSOR_MULTILEVEL;
COMMAND_CLASS_ASSOCIATION;
COMMAND_CLASS_VERSION;
COMMAND_CLASS_MANUFACTURER_SPECIFI
COMMAND_CLASS_TIME, COMMAND_CLASS_TIME_PARAMETERS
Note: This device supports 4 kinds of modes in Z-Wave: Off mode; Heating mode (Manual);
Energy Saving heating mode (Auto) ; Away heating mode (Vacation).
Users can set these 4 modes via COMMAND_CLASS_THERMOSTAT_MODE. And
COMMAND_CLASS_BASIC can switch among Heating mode & Energy saving heating mode.
COMMAND_CLASS_THERMOSTAT_SETPOINT can be used to set the heating
temperature threshold value in Heating mode or Energy saving heating mode.
Parameters Settings:
Add
Function Byte
Options Default
Remark
1 Upload temperature
format automatically 1
0x00Celsius 0x01Fahrenheit
0x02Follow the main display
0x02
2 Upload temperature
value automatically 1
0x00 OFF
0x01 Upload the difference
value only
0x02 Timing upload mode
only
0x03 Upload the
difference+timing upload
mode
0x03
3 Upload temperature
difference 2
Base on 0.1℃unit, 0x0005
by default, 5*0.1℃=0.5℃,
0x0003~0x03E8
0x0005
0.5℃

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 7
4 Upload time interval
regularly 2
Base on 1s unit, it suggest to
be set above 30s
0x000A~0xFFFF
0x001
E 30S
FF Factory setting 1 0x55 Restore the factory
setting(write only)
Parameters
setting back to
default value,
association
groups deleted
1-year Limited Warranty
MCOHome warrants this product to be free from defects in material and workmanship under
normal and proper use for one year from purchase date of the original purchaser. MCOHome will, at its
option, either repair or replace any part of its products that prove defective by reason of improper
workmanship or materials. THIS LIMITED WARRANTY DOES NOT COVER ANY DAMAGE TO
THIS PRODUCT THAT RESULTS FROM IMPROPER INSTALLATION, ACCIDENT, ABUSE,
MISUSE, NATURAL DISASTER, INSUFFICIENT OR EXCESSIVE ELECTRICAL SUPPLY,
ABNORMAL MECHANICAL OR ENVIRONMENTAL CONDITIONS, OR ANY
UNAUTHORIZED DISASSEMBLY, REPAIR OR MODIFICATION. This limited warranty shall not
apply if: (i) the product was not used in accordance with any accompanying instructions, or (ii) the
product was not used for its intended function. This limited warranty also does not apply to any product
on which the original identification information has been altered, obliterated or removed, that has not
been handled or packaged correctly, that has been sold as second-hand or that has been resold contrary
to Country and other applicable export regulations.
Secret Menu
In shutdown state, long press S3+S5 synchronically can enter into secret menu. Press S4 or S5 to
enter code 1234. Touch S3 to enter setting interface. Following are parameters which can be set.
Item
Explain Default Range Remark
P01 Temp. Setting upper
limit
37.0℃（99℉）
00-99.5℃（32-211℉）
Always confirm the
upper limit ＞
bottom limit
P02 Temp. Setting bottom
limit
5℃（41℉） 00-99.5℃（32-211℉）
P03 Slave Address 1
96
1~64
12~576
Reserved
P04 Hourly 24 12/24
P05
EH back by Temp.
differential
1.5℃（3℉） 0.0-10.0℃（0-18℉）
WH back by Temp.
differential
0.5℃（1℉） 0.0-10.0℃（0-18℉）
P06
EH Temp differential
0.0℃ (00℉) 0.0-10.0℃（0-18℉）
WH Temp differential
0.5℃（1℉） 0.0-10.0℃（0-18℉）

www.mcohome.com User Manual
MCOHome Technology Co., Ltd 8
P07 Anti-freeze
temperature setting
5℃（41℉） 0-30℃（32-86℉）
P08
Protection
temperature
55℃（131℉）
45-95℃（113-203℉）
OFF
Indoor temperature
control
OFF High temperature
control
P09
Power on state
OFF
OFF/OPN/PRU
= OFF electricity
power off，= OPN
electricity power
on，= PRU power
failure memory
P10 The time of
temperature change
2 0-99
P11 Temperature
calibration
0.0℃(00℉) -9.5-9.5℃（-16-16℉）
P12 Sound level 3 OF/0-9
P13 Backlit level 2 1-8/NO/OFF
P14 External temperature
0.0℃(00℉) -9.5-9.5℃（-16-16℉）
P15
External temperature
control switching
OFF ON/OFF Indoor temperature
control
ON ON/OFF External sensor
temperature control
P16
External temperature
display switching
OFF ON/OFF Indoor temperature
display
ON ON/OFF External temperature
display
P17 Temp. format OC OC/OF
=OC，Celsius；
=OF，Fahrenheit
（After modify
settings, to restore
the factory settings.）
P18
Restore factory
setting
Display: 53
Password: 55
00-99 Change 53 to 55,
and press S3 to
confirm
* After power failure:
0 indicates device will be in shutdown state (“OFF”) when power on again;
1 indicates device will be in working interface when power on again;
2 (default) indicates device will stay the status before power failure when power on again.