McQuay AGZ 030A User manual

Installation and Operation Manual IOM 686
Group: Chiller
Part Number: 062994901
Effective: March 1997
Supersedes: None
© 1997 McQuay International
Air-Cooled Global Chiller
Type AGZ 030A through 065A
60 Hertz, English and Metric
Scroll Compressors using Refrigerant R-22

2AGZ 030A through 065A IOM 686
Table of Contents
Introduction.........................................3
General Description....................................... 3
Inspection ....................................................... 3
Installation...........................................4
Handling......................................................... 4
Location.......................................................... 5
Service Access................................................ 5
Vibration Isolators......................................... 6
Water Piping................................................... 7
Flow Switch................................................... 9
Water Connections......................................... 9
Refrigerant Charge......................................... 9
Superheat and Subcooling............................. 9
Glycol Solutions..........................................10
Evaporator Water Flow and Pressure Drop 11
Physical Data.....................................13
Electrical Data...................................16
Field Wiring .................................................16
Dimensional Data..............................28
AGZ Unit Check-out.........................29
Water piping checkout .................................29
Refrigerant piping checkout........................29
Electrical Check Out....................................29
AGZ Troubleshooting Chart........................30
Global UNT Controller Installation
and Operation....................................31
General Description.....................................31
Optional Sensors..........................................31
Pre Start-up ..................................................31
Start-Up........................................................31
Shutdown......................................................32
Sequence of Operation.................................33
Standard Controller Setpoints (optional Zone
Terminal required to change values)...........33
Software Description (Global UNT Interface
Kit required to read or change variables)....34
Hot Gas Bypass (Optional)..........................34
Combination Filter Drier.............................35
System Adjustment ......................................35
Liquid Sightglass and Moisture Indicator...35
Refrigerant Charging ...................................35
Thermostatic Expansion Valve....................35
Crankcase Heaters........................................36
Water Cooler................................................36
Controller Inputs /Outputs..........................38
Additional Global UNT Controller Features41
Alarms ..........................................................43
ZONE TERMINAL (optional)....................44
Zone Terminal Glossary...............................48
Global UNT Controller Troubleshooting
Chart.............................................................50
MicroTech Controller Installation
and Operation....................................51
General Description.....................................51
Optional Sensor Packages ...........................51
Installation....................................................51
Sequence of Operation.................................60
Start-Up and Shutdown................................62
Keypad / Display..........................................63
Menu Descriptions.......................................66
Trouble Analysis for the AGZ MicroTech
Controller.....................................................77
Test Procedures............................................79
"McQuay" is a registered trademark of McQuay International
1997 McQuay International
"Illustrations cover the general appearance of McQuay International products at the time of publication and we
reserve the right to make changes in design and construction at anytime without notice"

IOM 686 AGZ 030A through 065A 3
Introduction
General Description
McQuay Air-Cooled Global water chillers are complete, self-contained automatic refrigerating units.
Every unit is completely assembled, factory wired,charged, and tested.Each unit consists of twin Air-
Cooled condensers with integral subcooler sections, multiple tandem scroll compressors, replaceable
tube dual circuit shell-and-tube evaporator, and complete refrigerant piping. Liquid line components
include manual liquid line shutoff valves, sight-glass/moisture indicators, solenoid valves, and double
diaphragm hydraulic element thermal expansion valves. Other features include compressor crankcase
heaters, an evaporator heater for chilled water freeze protection, limited pumpdown during “on” or
“off” periods, compressor lead-lag switch to alternate the compressor starting sequence, and sequenced
starting of compressors.
The electrical control center includes all safety and operating controls necessary for dependable
automatic operation. Condenser fan motors are fused in all three phases and started by their own
three-pole contactors. Compressors are not fused but may be protected by optional circuit breakers.
Inspection
Check all items carefully against the bill of lading.Inspect all units for damage upon arrival. Report
shipping damage and file a claim with the carrier. Check the unit name plate before unloading,making
certain it agrees with the power supply available. McQuay is not responsible for physical damage after
unit leaves the factory.
Note: Unit shipping and operating weights are available in the Physical Data tables
beginning on page 13.

4AGZ 030A through 065A IOM 686
Installation
Note: Installation is to be performed by qualified personnel who are familiar with local
codes and regulations.
WARNING
Sharp edges and coil surfaces are a potential hazard. Avoid contact with them.
Handling
Be careful to avoid rough handling of the unit. Do not push or pull the unit from anything other than
the base. Block the pushing vehicle away from the unit to prevent damage to the sheet metal cabinet
and end frame (see Figure 1).
To lift the unit, 2 1/2" (64mm) diameter lifting holes are provided in the base of the unit. Arrange
spreader bars and cables to prevent damage to the condenser coils or cabinet (see Figure 2).
Figure 1, Suggested pushing arrangement
Figure 2, Suggested lifting arrangement
These rigging holes
must be used.
Spreader Bars
recommended
(use caution)
Number of fans may vary
from this diagram. The
lifting method will remain
the same
Blocking is required
across full width

IOM 686 AGZ 030A through 065A 5
Location
Unit Placement
AGZ units are for outdoor applications and can be mounted on a roof or ground level. Set units on a
solid and level foundation. For roof mounted applications, install the unit on a steel channel or I-beam
frame to support the unit above the roof. For ground level applications, install the unit on a
substantial base that will not settle. A one piece concrete slab with footings extended below the frost
line is recommended. Be sure the foundation is level (within 1/2” [13 mm] over its length and width).
The foundation must support the operating weights listed in the Physical Data tables beginning on page
13.
On ground level applications protect fins against vandalism using the optional coil guards or by
erecting a screen fence. The fence must allow free flow of air to the condenser coil for proper unit
operation.
Clearances
The flow of air to and from the condenser coil must not be limited. Restricting air flow or allowing
air recirculation will result in a decrease in unit performance and efficiency. There must be no
obstruction above the unit that would deflect discharge air downward where it could be recirculated
back to the inlet of the condenser coil. The condenser fans are propeller type and will not operate with
ductwork on the fan outlet.
Install the unit with enough side clearance for air entrance to the coil and for servicing. Provide
service access to the evaporator, compressors, electrical control panel and piping components as
shown in Figure 3.
Do not allow debris to accumulate near the unit. Air movement may draw debris into the
condenser coil causing air starvation. Give special consideration to low ambient operation where
snow can accumulate. Keep condenser coils and fan discharge free of snow or other obstructions to
permit adequate airflow.
Sound Isolation
The ultra-low sound levels of the AGZ chiller is suitable for most applications. When additional
sound reduction is necessary, locate the unit away from sound sensitive areas. Avoid locations beneath
windows or between structures where normal operating sounds may be objectionable. Reduce
structurally transmitted sound by isolating water lines, electrical conduit and the unit itself. Use wall
sleeves and rubber isolated piping hangers to reduce transmission of water or pump noise into
occupied spaces. Use flexible electrical conduit to isolate sound through electrical conduit. Spring
isolators are effective in reducing the low amplitude sound generated by reciprocating compressors
and for unit isolation in sound sensitive areas.
Service Access
Each end of the unit must be accessible after installation for periodic service. Compressors, filter-
driers, and manual liquid line shutoff valves are accessible.High pressure control is located in the
control panel when using the Global UNT controller,and on the compressor when using the
MicroTech controller. Low pressure, and motor protector controls are on the compressor. Most other
operational, safety and starting controls are located in the unit control box.
The condenser fan and motors can be removed from the top of the unit.

6AGZ 030A through 065A IOM 686
Vibration Isolators
Vibration isolators are recommended for all roof mounted installations or wherever vibration
transmission is a consideration.
lists isolator loads and type.Table 2 lists spring isolator part numbers for all unit sizes. See
Dimensional Data for dimensions required to secure each isolator to the mounting surface.
Figure 3, Clearance requirements

IOM 686 AGZ 030A through 065A 7
The spring flex isolators are white type CP2-32, McQuay part number 047792932. A total of four per
unit is required.
Figure 4, Isolator Locations
Table 1, Isolator Loads at each Mounting Location with Aluminum Fins
Unit 1 2 3 4 Total Unit
Size Lb Kg Lb Kg Lb Kg Lb Kg Lb Kg
030AS 838 380 944 428 773 351 870 395 3425 1554
035AS 850 386 960 435 785 356 885 401 3480 1579
040AS 864 392 974 442 797 362 900 408 3535 1603
045AS 928 421 1048 475 858 389 966 438 3800 1724
050AS 940 426 1062 482 868 394 980 445 3850 1746
055AS 990 449 1118 507 915 415 1032 468 4055 1839
060AS 1006 456 1134 514 928 421 1047 475 4115 1867
065AS 1050 476 1184 537 970 440 1091 495 4295 1948
030AE 852 386 960 435 786 357 887 402 3485 1581
040AE 904 410 1017 461 834 378 940 426 3695 1676
050AE 980 445 1105 501 905 411 1020 463 4010 1819
Table 2, Isolator Loads at each Mounting Location with Copper Fins
Unit 1 2 3 4 Total Unit
Size Lb Kg Lb Kg Lb Kg Lb Kg Lb Kg
030AS 946 429 1066 484 873 396 985 447 3870 1755
035AS 960 435 1082 491 886 402 997 452 3925 1780
040AS 973 441 1096 497 899 408 1012 459 3980 1805
045AS 1038 471 1170 531 958 435 1079 489 4245 1926
050AS 1050 476 1184 537 970 440 1091 495 4295 1948
055AS 1154 523 1300 590 1066 484 1200 544 4720 2141
060AS 1166 529 1320 599 1078 489 1216 552 4780 2168
065AS 1252 568 1412 640 1156 524 1305 592 5125 2325
030AE 960 435 1083 491 887 402 1000 454 3930 1783
040AE 1066 484 1202 545 984 446 1108 503 4360 1978
050AE 1142 518 1288 584 1055 479 1190 540 4675 2121
Water Piping
Local authorities can supply the installer with the proper building and safety codes required for safe
and proper installation.
Install piping with minimum bends and changes in elevation to minimize pressure drop. Consider
the following when installing water piping:
1. Vibration eliminators to reduce vibration and noise transmission to the building.
2. Shutoff valves to isolate the unit from the piping system during unit servicing.

8AGZ 030A through 065A IOM 686
3. Manual or automatic air vent valves at the high points of the system. Install drains at the lowest
points in the system.
4. Ameans of maintaining adequate system water pressure (expansion tank or regulating valve).
5. Temperature and pressure indicators located at the unit to aid in unit servicing.
6. A strainer or other means of removing foreign matter from the water before it enters the pump.
Place the strainer far enough upstream to prevent cavitation at the pump inlet (consult pump
manufacturer for recommendations). The use of a strainer will prolong pump life and keep
system performance up.
7. Place a strainer in the water line just before the inlet of the evaporator.This will help prevent
foreign material from entering and decreasing the performance of the evaporator.
CAUTION
If separate disconnect is used for the 115V supply to the evaporator heating cable, mark
the disconnect clearly to ensure disconnect is not accidentally shut off during cold seasons.
8. The shell-and-tube evaporator has a thermostat and heating cable to prevent freeze-up down to -
20°F (-29°C). It is suggested that the heating cable be wired to a separate 110V supply circuit.
As shipped from the factory, the heating cable is wired to the control circuit. All water piping to
the unit must also be protected to prevent freezing.
9. If the unit is used as a replacement chiller on a previously existing piping system, flush the system
thoroughly before unit installation. Regular water analysis and chemical water treatment for the
evaporator loop is recommended immediately at equipment start-up.
10. The total water volume in the system should be sufficient to prevent frequent “on-off” cycling.
Turnover rate should not be less than 15 minutes for normal variable cooling loads. Turnover rate
for process cooling or a constant load, should not be less than 6 minutes.
11. When glycol is added to the water system for freeze protection, the refrigerant suction pressure
will be lower, cooling performance less, and water side pressure drop greater. If the percentage of
glycol is high, or if propylene is used instead of ethylene glycol, the added pressure drop and loss
of performance could be substantial. Reset the freezestat and low leaving water alarm
temperatures. The freezestat is factory set to default at 36°F (2.2°C). Reset the freezestat setting
to approximately 4 to 5 degrees F (2.3 to 2.8 degrees C) below the leaving chilled water setpoint
temperature. See the section titled “Glycol Solutions” for additional information concerning
glycol.
12. Perform a preliminary leak check before insulating the piping and filling the system.
13. Piping insulation should include a vapor barrier to prevent condensation and possible damage to
the building structure.
Figure 5, Typical field evaporator water piping

IOM 686 AGZ 030A through 065A 9
Flow Switch
Mount a water flow switch in either the entering or leaving water line to shut down the unit when
water flow is interrupted.
A flow switch is available from McQuay (part number 0017503300). It is a “paddle” type switch
and adaptable to any pipe size from 3” (76mm) to 8” (203mm) nominal. Certain minimum flow rates
are required to close the switch and are listed in Table 3. Installation should be as shown in Figure 6.
Connect the normally open contacts of the flow switch in the unit control center at terminals 5 and 6.
There is also a set of normally closed contacts on the switch that can be used for an indicator light or
an alarm to indicate when a “no flow” condition exists. Freeze protect any flow switch that is installed
outdoors.
NOTE: Differential pressure switches are not recommended for outdoor installation.
Table 3, Flow switch minimum flow rates
NOMINAL PIPE SIZE MINIMUM REQUIRED FLOW TO
INCHES (MM) ACTIVATE SWITCH - GPM (L/S)
1 (25.4) 6.00 (0.38)
11/4 (31.8) 9.80 (0.62)
11/2 (38.1) 12.70 (0.80)
2 (50.8) 18.80 (1.20)
21/2 (63.50 24.30 (1.50)
3 (76.20 30.00 (1.90)
4 (101.6) 39.70 (2.50)
5 (127.0) 58.70 (3.70)
6 (152.4) 79.20 (5.00)
Figure 6, Flow switch installation
Water Connections
Bring water piping to the evaporator through the side between the vertical supports.
Refrigerant Charge
All units are designed for use with R-22 and other refrigerants. See nameplate for specific refrigerant
used. Units are shipped with an operating charge. The operating charge
(using R-22) for each unit is shown in the Physical Data tables beginning on page 13.
Superheat and Subcooling
For optimum operation, set the evaporator superheat for 8 - 12°F (4.4 - 6.6°C) and condenser
subcooling (at the liquid shutoff valves) to 15°F (8.3°C).
Flow direction
marked on switch
1" (25mm) NPT flow
switch connection
Tee

10 AGZ 030A through 065A IOM 686
Glycol Solutions
The system glycol capacity, glycol solution flow rate in GPM, and pressure drop through the cooler
may be calculated using the following formulas and table.
1. Capacity -- Find the reduced capacity by multiplying the chiller’s capacity with water by the
capacity correction factor C.
2. Flow -- To determine evaporator gpm (or Delta-T) knowing Delta-T (or gpm) and capacity:
Glycol GPM (from table)=×−×
24 capacity glycol
Delta TG
( )
For Metric Applications -- To determine evaporator L/s (or Delta-T) knowing Delta-T (or L/s)
and kW:
Glycol L /s(from table)=× − ×
kW
Delta TFlow 4.18
3. Pressure drop -- To determine pressure drop through the evaporator, when using glycol, enter the
water pressure drop curve on page 12 at the actual glycol GPM. Multiply the water pressure drop
by PD correction factor from Table 4 or Table 5 to obtain corrected glycol pressure drop.
4. To determine the unit's power consumption when using glycol, multiply the water system kW by
factor kW.
Test coolant with a clean, accurate glycol solution hydrometer (similar to that found in service
stations) to determine the freezing point. Obtain percent glycol from the freezing point table below.
On glycol applications it is normally recommended by the supplier that a minimum of 25% solution by
weight be used for protection against corrosion.
CAUTION
Do not use an automotive grade antifreeze. Industrial grade glycols must be used.
Automotive antifreeze contains inhibitors which will cause plating on the copper tubes within
the chiller evaporator. The type and handling of glycol used must be consistent with local
codes.
Table 4, Ethylene glycol
%Freeze Point
E.G. °F °C Cap. kW GPM PD
10 26 -3 0.991 0.996 1.013 1.070
20 18 -8 0.982 0.992 1.040 1.129
30 7 -14 0.972 0.986 1.074 1.181
40 -7 -22 0.961 0.976 1.121 1.263
50 -28 -33 0.946 0.966 1.178 1.308
Table 5, Propylene glycol
%Freeze Point
P.G. °F °C Cap. kW GPM PD
10 26 -3 0.987 0.992 1.010 1.068
20 19 -7 0.975 0.985 1.028 1.147
30 9 -13 0.962 0.978 1.050 1.248
40 -5 -21 0.946 0.971 1.078 1.366
50 -27 -33 0.929 0.965 1.116 1.481
Note: The procedure
does not specify the
type of glycol. Use
the derate factors
found in Table 4 for
corrections when
using ethylene glycol
and those in Table 5
for propylene glycol.

IOM 686 AGZ 030A through 065A 11
Table 6, Capacity and power derates
Chilled Water Fouling Factor
Delta-T 0.00025 (0.044) 0.00075 (0.132) 0.00175 (0.308)
ALTITUDE °F °C Cap. kW Cap. kW Cap. kW
63.3 0.992 0.995 0.996 0.982 0.911 0.935
84.4 0.995 0.997 0.969 0.984 0.914 0.937
SEA 10 5.6 1.000 1.000 0.975 0.986 0.919 0.939
LEVEL 12 6.7 1.005 1.002 0.980 0.989 0.923 0.941
14 6.8 1.010 1.005 0.985 0.991 0.928 0.943
16 8.9 1.014 1.007 0.989 0.993 0.930 0.944
63.3 0.978 1.005 0.957 0.990 0.903 0.943
84.4 0.982 1.007 0.961 0.993 0.905 0.945
10 5.6 0.986 1.009 0.965 0.995 0.909 0.947
2000 feet 12 6.7 0.992 1.011 0.970 0.998 0.914 0.949
14 6.8 0.997 1.014 0.973 1.001 0.919 0.952
16 8.9 1.000 1.016 0.975 1.002 0.921 0.953
63.3 0.966 1.016 0.944 0.999 0.894 0.951
84.4 0.969 1.018 0.947 1.001 0.896 0.953
10 5.6 0.973 1.021 0.952 1.005 0.900 0.956
4000 feet 12 6.7 0.978 1.025 0.956 1.008 0.904 0.958
14 6.8 0.982 1.027 0.959 1.011 0.909 0.960
16 8.9 0.986 1.028 0.961 1.015 0.911 0.961
63.3 0.953 1.025 0.930 1.009 0.884 0.961
84.4 0.955 1.028 0.934 1.011 0.887 0.962
10 5.6 0.959 1.031 0.939 1.013 0.890 0.964
6000 feet 12 6.7 0.963 1.034 0.942 1.017 0.895 0.966
14 6.8 0.968 1.036 0.946 1.020 0.899 0.968
16 8.9 0.972 1.037 0.949 1.024 0.902 0.969
Evaporator Water Flow and Pressure Drop
Evaporator flow rate must fall between the minimum and maximum values shown in the evaporator
pressure drop table on page 12.
Measure the chilled water pressure drop through the evaporator at factory installed pressure taps.
It is important not to include the effect of valves or strainers in these readings.
Varying chilled water flow through the evaporator while the compressor(s) are operating is not
recommended.

12 AGZ 030A through 065A IOM 686
Figure 7, Pressure Drop Curve
045A-065A
030A-040A
NOMINAL MAXIMUM MINIMUM
Pressure Drop Flow Pressure Drop Flow Pressure Drop Flow
Unit (ft) of water KPa (GPM) (L / s) (ft) of
Water KPa (GPM) (L / s) (ft) of water KPa (GPM) KPa
030A 6.6 12.9 73.00 4.61 16.6 49.7 122.00 7.70 2.9 8.6 46.00 2.90
035A 8.3 24.8 82.00 5.17 20.6 61.7 136.00 8.58 3.5 10.6 51.00 3.22
040A 10.4 31.1 93.00 5.87 26.1 78.0 155.00 9.78 4.4 13.3 58.00 3.66
045A 6.8 20.3 106.00 6.69 16.9 50.6 176.00 11.10 2.9 8.7 66.00 4.16
050A 8.0 23.9 117.00 7.38 20.1 60.0 195.00 12.30 3.4 10.2 73.00 4.61
055A 10.2 30.5 130.00 8.20 25.4 76.0 216.00 13.63 4.3 12.7 80.00 5.05
060A 12.2 36.5 141.00 8.90 30.6 91.5 235.00 14.83 5.2 15.6 88.00 5.55
065A 14.0 41.8 148.00 9.34 35.2 105.2 247.00 15.58 5.9 17.8 92.00 5.80
Minimum and maximum flows are established to ensure the Delta-T for each unit size falls within the 6 - 16°F range for proper unit control.

IOM 686 AGZ 030A through 065A 13
Physical Data
Table 7, AGZ030AS Through 045AS
PHYSICAL DATA AGZ MODEL NUMBER
STANDARD EFFICIENCY 030AS 035AS 040AS 045AS
BASIC DATA Ckt.1 Ckt.2 Ckt.1 Ckt.2 Ckt.1 Ckt.2 Ckt.1 Ckt.2
Unit Capacity @ ARI Conditions (1), Tons (kW) 30.5 (107.2) 34.3 (120.5) 38.9 (136.7) 44.3 (156.0)
Number Of Refrigerant Circuits 2222
Unit Operating Charge, R-22, Lbs. 34 34 36 36 40 40 42 42
Unit Operating Charge, R-22, (kg) (15.4) (15.4) (16.3) (16.3) (18.1) (18.1) (19.0) (19.0)
Cabinet Dimensions, LxWxH, In. 94.0 x 88.2 x 86.2 94.0 x 88.2 x 86.2 94.0 x 88.2 x 86.2 94.0 x 88.2 x 86.2
Cabinet Dimensions, LxWxH, (mm) 2388 x 2241 x 2190 2388 x 2241 x 2190 2388 x 2241 x 2190 2388 x 2241 x 2190
Unit Operating Weight, Lb (kg) 3425 (1555) 3480 (1580) 3535 (1605) 3800 (1725)
Unit Shipping Weight, Lb (kg) 3350 (1520) 3405 (1545) 3460 (1570) 3695 (1675)
Add'l Weight If Copper Finned Coils, Lb (kg) 445 (200) 445 (200) 445 (200) 445 (200)
COMPRESSORS
Type Tandem Scrolls Tandem Scrolls Tandem Scrolls Tandem Scrolls
Nominal tonnage of each Compressor 7.5 9.0 9.0 9.0 10.0 10.0 10.0 13.0
Number Of Compressors per Circuit 2 2 2 2 2 2 2 2
Oil Charge Per Compressor, Oz. 140 140 140 140 140 140 140 140
Oil Charge Per Compressor, (g) (496) (496) (496) (496) (496) (496) (496) (496)
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Standard Staging - Circuit #1 in Lead
Standard 4 Stages 0-23-50-73-100 0-25-50-75-100 0-25-50-75-100 0-22-50-72-100
Standard Staging - Circuit #2 in Lead
Standard 4 Stages 0-27-50-77-100 0-25-50-75-100 0-25-50-75-100 0-28-50-78-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area,Sq. Ft. 46.4 46.4 46.4 46.4 46.4 46.4 46.4 46.4
Coil Face Area, (M
2
)(4.3) (4.3) (4.3) (4.3) (4.3) (4.3) (4.3) (4.3)
Finned Height x Finned Length, In. 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5
Finned Height x Finned Length, (mm) (2032 x
2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121)
Fins Per Inch x Rows Deep 16 x 2 16 x 2 16 x 2 16 x 2 16 x 2 16 x 2 16 x 2 16 x 2
Maximum Relief Valve Pressure Setting, psig (kPa) 450
(3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103)
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number Of Fans - Fan Diameter, In. (mm) 4 - 28 (712) 4 - 28 (712) 4 - 28 (712) 4 - 28 (712)
Number Of Motors - HP (kW) (2) 4 - 1.0 (0.7) 4 - 1.0 (0.7) 4 - 1.0 (0.7) 4 - 1.5 (1.1)
Fan And Motor RPM, 60Hz 1140 1140 1140 1140
60 Hz Fan Tip Speed, FPM (M/Sec) 8357 (35.4) 8357 (35.4) 8357 (35.4) 8357 (35.4)
60 Hz Total Unit Airflow, CFM (M
3
/sec) 34400 (16.2) 34400 (16.2) 34400 (16.2) 38000 (17.9)
DIRECT EXPANSION EVAPORATOR - BAFFLED SHELL AND THRU-TUBE
Diameter, in. - Length, Ft. 10 - 04 10 - 04 10 - 04 12 - 04
Diameter, (mm) - Length, (mm) (254) - (1220) (254) - (1220) (254) - (1220) (305) - (1220)
Water Volume, Gallons, (L) 9.1 (34.5) 9.1 (34.5) 9.1 (34.5) 12.8 (48.5)
Maximum Water Pressure, psig (kPa) 175 (1207) 175 (1207) 175 (1207) 175 (1207)
Maximum Refrigerant Working Pressure, psig
(kPa) 225 (1552) 225 (1552) 225 (1552) 225 (1552)
Water Inlet / Outlet Victaulic Connections, In. (mm) 4 (101.6) 4 (101.6) 4 (101.6) 4 (101.6)
Drain - NPT int, In. (mm) .375 (9.5) .375 (9.5) .375 (9.5) .375 (9.5)
Vent - NPT int, In. (mm) .375 (9.5) .375 (9.5) .375 (9.5) .375 (9.5)
NOTES:
1. Nominal capacity based on 95F ambient air and 54F/44F water range.
2. Units with 1.0 Hp Fan Motors, Uses 1.5 Hp Fan Motors when unit is 380V / 60 Hz and 575V / 60Hz.

14 AGZ 030A through 065A IOM 686
Table 8, AGZ050AS Through 065AS
PHYSICAL DATA AGZ MODEL NUMBER
STANDARD EFFICIENCY 050AS 055AS 060AS 065AS
BASIC DATA Ckt.1 Ckt.2 Ckt.1 Ckt.2 Ckt.1 Ckt.2 Ckt.1 Ckt.2
Unit Capacity @ ARI Conditions (1), Tons (kW) 48.9 (172.2) 54.1 (190.1) 58.9 (207.4) 61.6 (216.5)
Number of Refrigerant Circuits 2 2 2 2
Unit Operating Charge, R-22, Lb. 44 44 54 54 56 56 62 62
Unit Operating Charge, R-22, (kg) (18.1) (18.1) (22.6) (22.6) (23.5) (23.5) (28.1) (28.1)
Cabinet Dimensions, LxWxH, In. 94.0 x 88.2 x 86.2 94.0 x 88.2 x 86.2 94.0 x 88.2 x 86.2 94.0 x 88.2 x 96.2
Cabinet Dimensions, LxWxH, (mm) 2388 x 2241 x
2190 2388 x 2241 x 2190 2388 x 2241 x 2190 2388 x 2241 x 2444
Unit Operating Weight, Lb. (kg) 3850 (1745) 4055 (1840) 4115 (1865) 4295 (1950)
Unit Shipping Weight, Lb. (kg) 3745 (1700) 3950 (1790) 4010 (1820) 4190 (1900)
Add'l Weight If Copper Finned Coils, Lb. (kg) 445 (200) 665 (300) 665 (300) 830 (375)
COMPRESSORS
Type Tandem Scrolls Tandem Scrolls Tandem Scrolls Tandem Scrolls
Nominal Horsepower of each Compressor 13.0 13.0 13.0 15.0 15.0 15.0 15.0 15.0
Number of Compressors per Circuit 2 2 2 2 2 2 2 2
Oil Charge Per Compressor, Oz. 140 140 140 140 140 140 140 140
Oil Charge Per Compressor, (g) (496) (496) (496) (496) (496) (496) (496) (496)
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Standard Staging - Circuit #1 in Lead
Standard 4 Stages 0-25-50-75-100 0-23-50-73-100 0-25-50-75-100 0-25-50-75-100
Standard Staging - Circuit #2 in Lead
Standard 4 Stages 0-25-50-75-100 0-27-50-77-100 0-25-50-75-100 0-25-50-75-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area,Sq. Ft. 46.4 46.4 46.4 46.4 46.4 46.4 58.0 58.0
Coil Face Area, (M
2
)(4.3) (4.3) (4.3) (4.3) (4.3) (4.3) (5.4) (5.4)
Finned Height x Finned Length, In. 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 100x 83.5 100x 83.5
Finned Height x Finned Length, (mm) (2032 x
2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2540 x 2121) (2540 x 2121)
Fins Per Inch x Rows Deep 16 x 2 16 x 2 16 x 3 16 x 3 16 x 3 16 x 3 16 x 3 16 x 3
Maximum Relief Valve Pressure Setting, psig (kPa) 450
(3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103)
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number of Fans - Fan Diameter, In. (mm) 4 - 28 (712) 4 - 28 (712) 4 - 28 (712) 4 - 28(712)
Number of Motors - HP (kW) 4 - 1.5 (1.1) 4 - 1.5 (1.1) 4 - 1.5 (1.1) 4 - 1.5 (1.1)
Fan And Motor RPM, 60Hz 1140 1140 1140 1140
60 Hz Fan Tip Speed, FPM (M/Sec) 8357 (35.4) 8357 (35.4) 8357 (35.4) 8357 (35.4)
60 Hz Total Unit Airflow, CFM (M
3
/sec) 38000 (17.9) 36800 (17.4) 36800 (17.4) 38400 (18.1)
DIRECT EXPANSION EVAPORATOR - BAFFLED SHELL AND THRU-TUBE
Diameter, in. - Length, Ft. 12 - 04 12 - 04 12 - 04 12 - 04
Diameter, (mm) - Length, (mm) (305) - (1220) (305) - (1220) (305) - (1220) (305) - (1220)
Water Volume, Gallons, (L) 12.8 (48.5) 12.8 (48.5) 2.8 (48.5) 12.8 (48.5)
Maximum Water Pressure, psig (kPa) 175 (1207) 175 (1207) 175 (1207) 175 (1207)
Maximum Refrigerant Working Pressure, psig (kPa) 225 (1552) 225 (1552) 225 (1552) 225 (1552)
Water Inlet / Outlet Victaulic Connections, In. (mm) 4 (101.6) 4 (101.6) 4 (101.6) 4 (101.6)
Drain - NPT int, In. (mm) .375 (9.5) .375 (9.5) .375 (9.5) .375 (9.5)
Vent - NPT int, In. (mm) .375 (9.5) .375 (9.5) .375 (9.5) .375 (9.5)
NOTE:
1. Nominal capacity based on 95F ambient air and 54F/44F water range.

IOM 686 AGZ 030A through 065A 15
Table 9, AGZ030AE Through 050AE
PHYSICAL DATA AGZ MODEL NUMBER
HIGH EFFICIENCY 030AE 040AE 050AE
BASIC DATA Ckt.1 Ckt.2 Ckt.1 Ckt.2 Ckt.1 Ckt.2
Unit Capacity @ ARI Conditions (1), Tons (kW) 31.5 (110.7) 39.2 (137.7) 49.2 (172.8)
Number Of Refrigerant Circuits 2 2 2
Unit Operating Charge, R-22, Lbs. 40 40 50 50 52 52
Unit Operating Charge, R-22, (kg) (16.3) (16.3) (22.6) (22.6) (23.5) (23.5)
Cabinet Dimensions, LxWxH, In. 94.0 x 88.2 x 86.2 94.0 x 88.2 x 86.2 94.0 x 88.2 x 86.2
Cabinet Dimensions, LxWxH, (mm) 2388 x 2241 x 2190 2388 x 2241 x 2190 2388 x 2241 x 2190
Unit Operating Weight, Lbs. (kg) 3485 (1580) 3695 (1675) 4010 (1820)
Unit Shipping Weight, Lbs. (kg) 3410 (1545) 3620 (1640) 3905 (1770)
Add'l Weight If Copper Finned Coils, Lbs. (kg) 445 (200) 665 (300) 830 (375)
COMPRESSORS Type Tandem Scrolls Tandem Scrolls Tandem Scrolls
Nominal Horsepower of each Compressor 7.5 9.0 9.0 9.0 10.0 10.0
Number Of Compressors per Circuit 2 2 2 2 2 2
Oil Charge Per Compressor, Oz. 140 140 140 140 140 140
Oil Charge Per Compressor, (g) (496) (496) (496) (496) (496) (496)
CAPACITY REDUCTION STEPS - PERCENT OF COMPRESSOR DISPLACEMENT
Standard Staging - Circuit #1 in Lead
Standard 4 Stages 0-23-50-73-100 0-25-50-75-100 0-25-50-75-100
Standard Staging - Circuit #2 in Lead
Standard 4 Stages 0-27-50-77-100 0-25-50-75-100 0-25-50-75-100
CONDENSERS - HIGH EFFICIENCY FIN AND TUBE TYPE WITH INTEGRAL SUBCOOLING
Coil Face Area,Sq. Ft. 46.4 46.4 46.4 46.4 46.4 46.4
Coil Face Area, (M
2
)(4.3) (4.3) (4.3) (4.3) (4.3) (4.3)
Finned Height x Finned Length, In. 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5 80 x 83.5
Finned Height x Finned Length, (mm) (2032 x
2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121) (2032 x 2121)
Fins Per Inch x Rows Deep 16 x 2 16 x 2 16 x 3 16 x 3 16 x 3 16 x 3
Maximum Relief Valve Pressure Setting, psig (kPa) 450 (3103) 450
(3103) 450 (3103) 450 (3103) 450 (3103) 450 (3103)
CONDENSER FANS - DIRECT DRIVE PROPELLER TYPE
Number Of Fans - Fan Diameter, In. (mm) 4 - 28 (712) 4 - 28 (712) 4 - 28 (712)
Number Of Motors - HP (kW) 4 - 1.0 (0.7) 4 - 1.0 (0.7) 4 - 1.5 (1.1)
Fan And Motor RPM, 60Hz 1140 / 950 1140 / 950 1140 / 950
60 Hz Fan Tip Speed, FPM (M/Sec) 8357 (35.4) 8357 (35.4) 8357 (35.4)
60 Hz Total Unit Airflow, CFM (M
3
/sec) 34400 (16.2) 33600 (15.9) 36800 (17.4)
DIRECT EXPANSION EVAPORATOR - BAFFLED SHELL AND THRU-TUBE
Diameter, in. - Length, Ft. 10 - 04 10 - 04 12 - 04
Diameter, (mm) - Length, (mm) (254) - (1220) (254) - (1220) (305) - (1220)
Water Volume, Gallons, (L) 9.1 (34.5) 9.1 (34.5) 12.8 (48.5)
Maximum Water Pressure, psig (kPa) 175 (1207) 175 (1207) 175 (1207)
Maximum Refrigerant Working Pressure, psig (kPa) 225 (1552) 225 (1552) 225 (1552)
Water Inlet / Outlet Victaulic Connections, In. (mm) 4 (101.6) 4 (101.6) 4 (101.6)
Drain - NPT int, In. (mm) .375 (9.5) .375 (9.5) .375 (9.5)
Vent - NPT int, In. (mm) .375 (9.5) .375 (9.5) .375 (9.5)
NOTE:
Nominal capacity based on 95F ambient air and 54F/44F water range.

16 AGZ 030A through 065A IOM 686
Electrical Data
Field Wiring
CAUTION
Internal power wiring to the compressors for single and multiple point option are different.
Field wiring must be installed according to unit wiring diagram.
Wiring must comply with all applicable codes and ordinances. Warranty is void if wiring is not in
accordance with specifications. Copper wire is required for all power lead terminations at the unit.
Aluminum or copper can be used for all other wiring.
AGZ units have internal power wiring for single point power connection. A single large power
terminal block is provided and wiring within the unit is sized in accordance with the National
Electrical Code. A single field supplied fused disconnect is required. An optional factory mounted
transformer may be installed.
If the evaporator heater is on a separate disconnect switch from the main unit power supply,the
unit may be shut down without defeating the freeze protection provided by the cooler heater.
Table 10, AGZ030A - 065A, 60 Hz, Single Point Power Electrical Data
Minimum POWER SUPPLY Max. Fuse
AGZ Circuit Field Wire Hub or
Unit Volts Ampacity Wire Nominal HACR
Breaker
Size (MCA) Quantity Gauge Quantity Size Size
208 129 3 1 1 1.25 (32) 150
230 129 3 1 1 1.25 (32) 150
030AS 380 86 3 3 1 1.25 (32) 100
030AE 460 68 3 4 1 1.00 (25) 80
575 53 3 6 1 1.00 (25) 60
208 143 3 1/0 11.50 (38) 150
230 143 3 1/0 11.50 (38) 150
035AS 380 93 3 3 1 1.25 (32) 110
460 73 3 4 1 1.00 (25) 80
575 58 3 4 1 1.00 (25) 70
208 159 3 2/0 11.50 (38) 175
230 159 3 2/0 11.50 (38) 175
040AS 380 111 3 2 1 1.25 (32) 125
040AE 460 78 3 3 1 1.25 (32) 90
575 67 3 4 1 1.00 (25) 80
208 180 3 3/0 12.00 (51) 175
230 180 3 3/0 12.00 (51) 175
045AS 380 123 3 1 1 1.25 (32) 150
460 88 3 2 1 1.25 (32) 90
575 76 3 3 1 1.25 (32) 80
208 191 3 3/0 12.00 (51) 225
230 191 3 3/0 12.00 (51) 225
050AS 380 134 3 1/0 11.50 (38) 150
050AE 460 94 3 2 1 1.25 (32) 110
575 83 3 3 1 1.25 (32) 100
208 221 3 4/0 12.00 (51) 250
230 221 3 4/0 12.00 (51) 250
055AS 380 148 3 1/0 11.50 (38) 175
460 103 3 2 1 1.25 (32) 125
575 87 3 2 1 1.25 (32) 100
208 247 3 250 1 2.50 (64) 250
230 247 3 250 1 2.50 (64) 250
060AS 380 161 3 2/0 11.50 (38) 175
460 112 3 2 1 1.25 (32) 125
575 90 3 2 1 1.25 (32) 100
208 247 3 250 1 2.50 (64) 250
230 247 3 250 1 2.50 (64) 250
065AS 380 161 3 2/0 11.50 (38) 175
460 112 3 2 1 1.25 (32) 125
575 90 3 2 1 1.25 (32) 100

IOM 686 AGZ 030A through 065A 17
Table 11, AGZ030A - 065A, 60 Hz, Compressor and Condenser Fan Motor Amp Draw
Rated Load Amps Locked Rotor Amps
AGZ Compressors No. Of Compressors
Unit Volts No. No. Fan Fan Fan Across-The-Line
Size 1 & 3 2 & 4 Motors Motors Motors No.1 & 3 No.2 & 4
(Each) (Each) (Each) (Each) (Each) (Each)
208 22.9 29.9 4.0 417.0 169 232
230 22.9 29.9 4.0 417.0 189 232
030AS 380 14.9 18.6 3.4 414.4 112 144
030AE 460 12.5 15.3 2.0 48.5 94 116
575 9.1 11.6 2.2 410.3 74 97
208 29.9 29.9 4.0 417.0 232 232
230 29.9 29.9 4.0 417.0 232 232
035AS 380 18.6 18.6 3.4 414.4 144 144
460 15.3 15.3 2.0 48.5 116 116
575 11.6 11.6 2.2 410.3 97 97
208 33.6 33.6 4.0 417.0 255 255
230 33.6 33.6 4.0 417.0 255 255
040AS 380 22.8 22.8 3.4 414.4 151 151
040AE 460 16.4 16.4 2.0 48.5 127 127
575 13.7 13.7 2.2 410.3 100 100
208 33.6 39.5 5.8 423.7 255 318
230 33.6 39.5 5.8 423.7 255 318
045AS 380 22.8 28.2 3.4 414.4 151 188
460 16.4 19.3 2.8 410.7 127 158
575 13.7 17.3 2.3 411.5 100 125
208 39.5 39.5 5.8 423.7 318 318
230 39.5 39.5 5.8 423.7 318 318
050AS 380 28.2 28.2 3.4 414.4 188 188
050AE 460 19.3 19.3 2.8 410.7 158 158
575 17.3 17.3 2.3 411.5 125 125
208 39.5 52.6 5.8 423.7 318 411
230 39.5 52.6 5.8 423.7 318 411
055AS 380 28.2 34.6 3.4 414.4 188 249
460 19.3 23.7 2.8 410.7 158 187
575 17.3 19.0 2.3 411.5 125 150
208 52.6 52.6 5.8 423.7 411 411
230 52.6 52.6 5.8 423.7 411 411
060AS 380 34.6 34.6 3.4 414.4 249 249
460 23.7 23.7 2.8 410.7 187 187
575 19.0 19.0 2.3 411.5 150 150
208 52.6 52.6 5.8 423.7 411 411
230 52.6 52.6 5.8 423.7 411 411
065AS 380 34.6 34.6 3.4 414.4 249 249
460 23.7 23.7 2.8 410.7 187 187
575 19.0 19.0 2.3 411.5 150 150
Table 12, AGZ030A - 065A, 60 Hz Single Point Power, Field Wiring Data
Wiring to Standard Wiring to Optional
AGZ Power Block Non-Fused Disconnect Switch
Unit Volts Terminal Connector Wire Range Terminal Connector Wire Range
Size Amps (Copper Wire Only) Amps (Copper Wire Only)
208 175 #12 - 2/0 225 # 3 - 300 MCM
230 175 #12 - 2/0 225 # 3 - 300 MCM
030AS 380 175 #12 - 2/0 100 #14 - 1/0
030AE 460 175 #12 - 2/0 100 #14 - 1/0
575 175 #12 - 2/0 100 #14 - 1/0
208 175 #12 - 2/0 225 # 3 - 300 MCM
230 175 #12 - 2/0 225 # 3 - 300 MCM
035AS 380 175 #12 - 2/0 100 #14 - 1/0
460 175 #12 - 2/0 100 #14 - 1/0
575 175 #12 - 2/0 100 #14 - 1/0
208 175 #12 - 2/0 225 # 3 - 300 MCM
230 175 #12 - 2/0 225 # 3 - 300 MCM
040AS 380 175 #12 - 2/0 150 #4 - 4/0
040AE 460 175 #12 - 2/0 100 #14 - 1/0
575 175 #12 - 2/0 100 #14 - 1/0
208 335 # 4 - 400 MCM 225 # 3 - 300 MCM
230 335 # 4 - 400 MCM 225 # 3 - 300 MCM
045AS 380 175 #12 - 2/0 150 #4 - 4/0
460 175 #12 - 2/0 100 #14 - 1/0
575 175 #12 - 2/0 100 #14 - 1/0
Table continued on next page

18 AGZ 030A through 065A IOM 686
Table 12, AGZ030A - 065A, 60 Hz Single Point Power, Field Wiring Data (continued)
Wiring to Standard Wiring to Optional
AGZ Power Block Non-Fused Disconnect Switch
Unit Volts Terminal Connector Wire Range Terminal Connector Wire Range
Size Amps (Copper Wire Only) Amps (Copper Wire Only)
208 335 # 4 - 400 MCM 225 # 3 - 300 MCM
230 335 # 4 - 400 MCM 225 # 3 - 300 MCM
050AS 380 335 # 4 - 400 MCM 150 #4 - 4/0
050AE 460 175 #12 - 2/0 150 #4 - 4/0
575 175 #12 - 2/0 150 #4 - 4/0
208 335 # 4 - 400 MCM 400 250 - 500 MCM
230 335 # 4 - 400 MCM 400 250 - 500 MCM
055AS 380 335 # 4 - 400 MCM 250 #4 - 350 MCM
460 175 #12 - 2/0 150 #4 - 4/0
575 175 #12 - 2/0 150 #4 - 4/0
208 335 # 4 - 400 MCM 400 250 - 500 MCM
230 335 # 4 - 400 MCM 400 250 - 500 MCM
060AS 380 335 # 4 - 400 MCM 250 #4 - 350 MCM
460 175 #12 - 2/0 150 #4 - 4/0
575 175 #12 - 2/0 150 #4 - 4/0
208 335 # 4 - 400 MCM 400 250 - 500 MCM
230 335 # 4 - 400 MCM 400 250 - 500 MCM
065AS 380 335 # 4 - 400 MCM 250 #4 - 350 MCM
460 175 #12 - 2/0 150 #4 - 4/0
575 175 #12 - 2/0 150 #4 - 4/0
Notes for “Electrical Data Single Point” Power:
1. Unit wire size ampacity (MCA) is equal to 125% of the largest compressor-motor RLA plus
100% of RLA of all other loads in the circuit including the control transformer.
2. If the control transformer option is furnished, no separate 115v power is required.
3. If a separate 115V power supply is used for the control circuit, then the wire sizing amps is 10
amps for all unit sizes.
4. Recommended power lead wire sizes for 3 conductors per conduit are based on 100% conductor
ampacity in accordance with NEC. Voltage drop has not been included. Therefore, it is
recommended that power leads be kept short. All terminal block connections must be made with
copper (type THW) wire.
5. “Recommended Fuse Sizes” are selected at approximately 150% to 175% of the largest
compressor RLA, plus 100% of all other loads in the circuit.
6. “Maximum Fuse Sizes” are selected at approximately 225% of the largest compressor RLA, plus
100% of all other loads in the circuit.
7. The recommended power lead wire sizes are based on an ambient temperature of 86° F.
Ampacity correction factors must be applied for other ambient temperatures. Refer to the
National Electrical Code Handbook.
Voltage Limitations:
Within ±10 percent of nameplate rating
Notes for “Compressor and Condenser Fan Amp Draw”:
1. Compressor RLA values are for wiring sizing purposes only but do not reflect normal operating
current draw at rated capacity. If unit is equipped with SpeedTrol condenser fan motors, the first
motor on each refrigerant circuit is a single phase, 1hp motor, with a FLA of 2.8 amps at 460
volts, 5.6 amps at 208, 230, 380, and 575 volts.
2. Compressor LRA for reduced inrush start are for the first winding only. If the unit is equipped
with SpeedTrol motors, the first motor is a single phase, 1 hp motor, with a LRA of 7.3 amps at
460 volts, 14.5 amps at 208, 230, 380, and 575 volts.
Notes for “Field Wiring Data”
1. Requires a single disconnect to supply electrical power to the unit. This power must be fused.
2. All field wiring to unit power block or optional non-fused disconnect switch must be copper.
3. All field wire size values given in table apply to 75° C rated wire per NEC.

IOM 686 AGZ 030A through 065A 19
Figure 8, Typical Field Wiring with Global UNT Controller
UNITMAI
N
TERMINALBLOCK
DISCONNECT
(BYOTHERS)
3PHASE
POWER
SUPPLY
GNDLUG
TOCOMPRESSOR(S)
ANDFANMOTORS
FUSEDCONTROL
CIRCUITTRANSFORMER
OPTION
10A
FUSE
NNB
TB2
10A
FUSE
1
(BYOTHERS)
(BYOTHERS)
(BYOTHERS)
N
SEPARATEEVAPORATOR
HEATERPOWER
OPTION
DISCONNECT
DISCONNECT
(BYOTHERS)
(BYOTHERS)
13
16
545
IFSEPARATEEVAPORATOR
HEATERPOWEROPTION
ISUSED-REMOVE
WIRES540AND545.
120VAC
CONTROLPOWER
120VAC
TB3
19
28
FACTORYSUPPLIEDALARM
FIELDWIRED
ALARMBELL
ALARMBELL
OPTION24VAC
GND
TB7
140
141
AUTO
OFF
MANUAL
ON
TIME
CLOCK
AMBIENT
THERMOSTAT
REMOTESTOP
(BYOTHERS)
CHWFLOWSWITCH
(BYOTHERS)
142
143
133
134
135
MJ
SEEOPTIONSBELOW
(ONLYONESELECTION
AVAIL.ATATIME.)
IFREMOTESTOPCONTROL
ORTIMECLOCK
ISUSED,REMOVEJUMPER
FROMTERM140TO141.
2540
CONTROL
CIRCUIT
FUSE
0-10V-DEMANDLIMIT
TEMP.-ZONETEMP.
2-10V-REMOTERESET
TEMP.-RETURNEVAP.WATER
TEMP.-*OUTSIDEAIR
*STANDARDSELECTION
120VAC
TIMEDELAY

20 AGZ 030A through 065A IOM 686
Figure 9, Typical Field Wiring Diagram with MicroTech Controller
UNITMAI
N
TERMINALBLOCK
DISCONNECT
(BYOTHERS)
3PHASE
POWER
SUPPLY
GNDLUG
TOCOMPRESSOR(S)
ANDFANMOTORS
FUSEDCONTROL
CIRCUITTRANSFORMER
OPTION
10A
FUSE
NNB
TB2
10A
FUSE
1
(BYOTHERS)
(BYOTHERS)
(BYOTHERS)
N
SEPARATEEVAPORATOR
HEATERPOWER
OPTION
DISCONNECT
DISCONNECT
(BYOTHERS)
(BYOTHERS)
13
16
540545
IFSEPARATEEVAPORATOR
HEATERPOWEROPTION
ISUSED-REMOVE
WIRES540AND545.
9
10
5A
24VOR120VAC
120VAC
CONTROLPOWER
120VAC
(BYOTHERS)
NCHWPUMPRELAY
(BYOTHERS)
SOLIDSTATERELAY
24VOR120VAC
1.5AMPSMAX.
TB3
19
28
FACTORYSUPPLIEDALARM
FIELDWIRED
ALARMBELL
ALARMBELL
OPTION24VAC
GND
TB7
140
141
AUTO
OFF
MANUAL
ON
TIME
CLOCK
AMBIENT
THERMOSTAT
REMOTESTOP
(BYOTHERS)
CHWFLOWSWITCH
(BYOTHERS)
142
143
134
135
133
132
131
4-20MAFOR
CHWRESET
(BYOTHERS)
4-20MAFOR
DEMANDLIMIT
(BYOTHERS)
GND
137
138
139
GND
3
4
5
COMMUNICATION
PORT"B"
MJIFREMOTESTOPCONTROL ISUSED,REMOVEJUMPER
FROMTERM140TO141.
*(CONNECTIONTORMS
(REMOTEMONITORINGSEQUENCE)
ORTONMP
(NETWORKMASTERPANEL)
*MICROTECHONLY
2
CONTROL
CIRCUIT
FUSE
120VAC
*