MD SPORTS DH44109 User manual

MODEL: DH44109
Please contact us before returning the product to the store.
Toll Free: 877-472-4296

LIMITED 90 DAYS WARRANTY
1
This product is covered by a limited warranty that is effective for 90 days
from the date of purchase. The warranty covers any defects in parts and
workmanship.
This Limited Warranty gives you specific legal rights and you may also have
other rights which very from one state (province) to another.
If, during the limited warranty period, a part is found to be defective or
breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, tabletops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper
usage, alteration, misuse, abuse, accidental damage or neglect.
Attention: Since you build all tables upside down, please inspect table tops
and playing surfaces right away before putting together.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required
before any warranty service is initiated. All requests for warranty service can
be submitted by email, in writing or by contacting our Consumer service
Department at:
TOLL FREE: 877-472-4296
WEBSITE: www.medalsports.com.tw
*Please do not call our 800 NUMBER as well as email us. This will result in
duplicate orders and charges will occur.
*Please note that all damaged table tops need to be returned to the store.
We do not replace any tabletops or playing surfaces.
PLEASE CONTACT US BEFORE RETURNING THE
PRODUCT TO THE STORE. THANK YOU VERY MUCH!

Phillips Screwdriver – Not Included
Standard (Flat Head Screwdriver) – Not Included
Allen Wrench - Included
TOOLS REQUIRED:
ASSEMBLY TIPS:
:

!



!
2
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least two adults are required.
Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 -
2 -
Please Keep Your Instructions! Your Model number is necessary should you need to contact
us. Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts identifier below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on:
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
877-472-4296
Power Tools
- Set Low Torgue
High Torque
over tightened
High Torque
over tightened
CAUTION !
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.

DH 44109 PARTS LIST
RIGHT TABLE SURFACE
2 PIECES
6MM WASHER
24 PIECES
WRENCH
1 PIECE
M6 NUT
8 PIECES
16MM SPACER
8 PIECES
LEFT TABLE SURFACE
2 PIECES
CURVED OUTER LEG
WITH CAPS
2 PIECES
CURVED INNER LEG
WITH CAPS
2 PIECES
M6 X 47MM BOLT
8 PIECES
M6 X 42MM BOLT
8 PIECES
PLASTIC LEG PANEL
WITH FRAME
2 PIECES
ALLEN KEY
1 PIECE
NET POST - A
1 PIECE
WHEEL
4 PIECES
END APRON 1.3M
2 PIECES
M5 X 15MM SCREW
121 PIECES
LEG BRACKET
12 PIECES
MOLDED PROTECTIVE
CORNER
4 PIECES
LINKAGE TUBE WITH
STOP BRACKET
2 PIECES
LINKAGE TUBE
2 PIECES
BRACKET
6 PIECES
NET
1 PIECE
SAFTEY STRAP
1 SET
SIDE APRON 1.25M
3 PIECES
SHORT SIDE APRON
1 PIECE
3
LOCK PIN
2 PIECES
OUTER LEG CAP
4 PIECES
INNER LEG CAP
4 PIECES
PRE-INSTALLED PRE-INSTALLED
6
11
2 3 4 51
7 8 9 10
12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
ELECTRONIC SCORER
1 PIECE
CONNECTING WIRE
1 PIECE
STORAGE BAG
1 PIECE
SERVE
HOME
SERVE
VISITOR
31 32 33 34
DOUBLE SIDE TAPE
3 PIECES
KEY
1 PIECE
NET POST - B
1 PIECE
35
TABLE TENNIS BALL
2 PIECES

4
FIG. 1
2
1
1
2
9
24
18
Center
Player
Player
1. Find a clean, level place to begin the assembly of your Table Tennis Table. The table will be assembled upside down
and then turned over. This is a heavy game and tuning it over will require at least two strong adults.
2. Remove all of the parts from box and verify that you have all of the listed parts as shown on the Parts List.
Carefully cut or tear the four carton corners so that the bottom of the box can act as your workarea.
3. Place the Right Table Surface (#1) and Left Table Surface (#2) with the painted surface facing down on a flat surface.
4. Connect together using three Bracket (#9) using twelve Screws (#18). See Fig.1A.
5. Repeat the above steps for another Table Surface.
6. Attach the Safety Strap (#24) using three Screws (#18).
ASSEMBLY INSTRUCTIONS
FIG.1
Note:
Align the inside seams of
each sections so that
pre-drilled holes line up
across from each other. FIG. 1A
18
9
18
24
1
36 37
TABLE TENNIS PADDLE
2 PIECES
CONTROL BOX
1 PIECE

5
6
5
Center
Player
7. Place one Curved Outer Leg (# 5) on the player end of the table half and one Curved Inner Leg (#6) on the center
end of the table half, and then using the Leg Bracket (#19) attach legs to the table with twenty-four Screw (#18).
NOTE: Make sure that the oval cut-out in the Leg Bracket are facing the center of the table for proper installation.
8. Repeat steps for Curved Legs of the other table half.
FIG.2
27
26
FIG. 2
19
18

FIG.3
9. Attach one end of the Linkage Tube (#8) to the inside of the Curved Outer Leg (#5) using one Bolt (#3), two Washers
(#4), one Spacer (#14) and one Nut (#13).
10. Repeat the same for the other end of this Linkage Tube, only attaching it to the outside of the Curved Inner Leg (#6).
11. Attach one end of the Linkage Tube with Stop Bracket (#7) to the inside of the Curved Outer Leg (#5) using one Bolt
(#3), two Washers (#4), one Spacer (#14) and one Nut (#13).
12. Repeat the same for the other end of this Linkage Tube, only attaching it to the outside of the Curved Inner Leg (#6).
13. Next attach the Lock Pin (#10) to the bottom of the table using four Screws (#18)
14. Repeat the above steps for the other table half.
14
13
4
3
4
7
14 43
413
Center
18
8
10
7
Player
5
6
6
FIG. 3
Note:
Be careful of the assembly direction on
pictures when you assemble the Linkage
Tube #7 and #8 in order to fit the folding
function.

7
FIG. 4A
17
18
23 22
18
17
23
FIG.4
15. Place the Molded Protective Corners (#17) flush with table corner using twelve Screws (#18). See FIG.4A
16. Place the End Apron (#22) between the Corners(#17) using four Screws (#18) per End Apron. See FIG.4
17. Place the SideApron (#23) and Storage Bag (#30) flush with table edge at the side of the table using four Screws
(#18) per Side Apron. See FIG.4.
NOTE: Make sure the all Aprons are inside the Molded Protective Corners.
FIG. 4
Center
Player
30

FIG.5
18. Place the Wheel(#25) into the Curved Inner Legs.
19. With the logo upside-down, attach the Plastic Leg Panel (#21) to the Curved Inner Leg (#6) using two Bolts (#11)
and two Washers (#4). NOTE: Do not tighten securely at this time.
20. Repeat the above steps for the other side of this table half.
21. Place the Short Side Apron (#34) flush with table edge at the side of the table using four Screws (#18). See FIG.5.
8
FIG. 5
4
11
6
5
25
21
Center
Player
2
1
34
18

9
FIG. 6
FIG.6
22. Before turning the table over, make sure to push the Curved Inner Leg (#6) towards the center of the table in order
to engage the stop. NOTE: Two adults are required to turn this table over
23. One person should stand at each center of the table and turn the table over completely so that it rests on its legs.
24. Standing at the sides of the table, place the two table halves so they are inches apart.
NOTE: Be careful that you do not push either half backwards as this may cause the legs to fold!
25. Attach the Plastic Leg Panel and Frame (#21) to the opposite table half using two Bolts (#11) and two Washers
(#4).See FIG. 6. Now go back and tighten all the connections.
Caution:
Two strong adults are recommended to
turn the table over as shown.
A. TURN TABLE
ON ITS SIDE
B. FOLD LEGS AND
TABLE HALVES AND
LOCK IN PLACE
C. LIFT TABLE AND
TURN IN THE AIR
D. DO NOT LEAN
TABLE ON ITS LEGS! E. SET TABLE DOWN
EVENLY ON ALL
WHEELS, TO PREVENT
BREAKING LEGS
DE
11
11
4
Note: Please leave 10mm distance
between table centers.

FIG.7
10
26. Attach the Net Post A & B (#16 & #31) at the middle of the table and slide the net over the post. Stretch the Net (#15)
across the center of the table and slip the net over the post on the opposite side. See FIG. 7.
27. Place the Control Box (#37) at a player’s left corner and install it between the Apron Corner and Short Side Apron
(#34) using two Screws (#18). See FIG. 7A.
28. Place the Electronic Scorer (#28) onto the Net Post - B(#31) . See FIG. 7.
29. From underneath the table, insert Connecting Wire (#29) into the Electronic Scorer (#28) and the Control Box (#37).
See FIG. 7B.
30. Peel the wax paper off the Double Side Tape (#32) and attach it to the Connecting Wire (#29) at the underside of the
table. See FIG. 7C
FIG. 7
FIG. 7A
37
18
Underside
table surface
37
29
FIG. 7B
Underside
table surface
32
29
FIG. 7C
31
31
15
15
16
28
37
18

32. Folding the table - First fold the side of the table without the net clip. Hold the end securely and lift the table.
Make sure the Lock Pin (#10) is locked. Attach the Safety Strap (#24) to prevent the sides from falling.
Repeat for the other side.
33. To unfold the table - First release the Lock Pin (#10) and Safety Strap (#24). Then pull the bottom of the large
leg and slowly lower the table to the floor.
11
10
31. Engage the Caster (wheels ) Lock.
FIG.8
Note: When the table is in its storage
position, always attach the safety strap
to prevent the sides from falling.
FIG. 8
24
21
2
1
Reverse
1
2
Note: Remove the Post and
Net before folding the table.

12
Batteries Replacement Instructions
Note: AAA Batteries are not included.
Step 1: Use a screwdriver to loosen the screw.
Step 2: Use the provided key to pull the battery box out.
Use the key in this position to
pull the box out.
Key
33

13
Step 3：
Step 4: After having placed the batteries, push the box back inside the device.
Step 5: Use the screwtotighten the cover of the box.
Note: Make sure to put all the batteries in the right way inside the box.
Positive pole（+）
Negative pole（-）
+
-
+
-
+
-
+
-
Push the box inside

14
SCORER OPERATION
1. Remove the battery cover and insert four AAA batteries into the battery box. AAA Batteries not included.
2. Turn on the scorer by pressing the “ON/OFF” button, therewith starting the game. Both screens will show a
player, the HOME Serve “ ” indicator will be light up. If “VISITOR” is selected instead; the VISITOR Server “ ”
indicator will light up. Now, both scoreindicators will show “00”.
4. When the “HOME” or “VISITOR” player scores a point, press the Home or Visitor “+” button to record the point.
You can also press the Home or Visitor“-“ button to deduct a point.
6. When both players have 10 points, the game has to be continued until one of the players wins by a margin of
2 points.The Serve indicator will also automatically choose a player to serve the ball.
button, the scorer will automatically turn back to the beginning status indicated in step 2.
Note:
a) You can press and hold the “RESET” button for 3 seconds at any time, to set the scorer back to the beginning status
indicated in Step 2.
button again to turn it back on.
ElectronicScorer
Control Box

!



This device complies with the part 15of the FCC rules. Operation is subject to the followingtwo conditions :
(1) This device may notcause harmful interference, and
(2) This device must accept any interference received, including interference that maycause undesired operation.