Meanwell NPB-450 NFC Series User manual

注：完成上述步驟1~7設定後，再次重複步驟3~4即可讀取並確認調整後的充電器
是否已如實完成參數修改。
NPB-450-xxNFC充電器使⽤⼿冊
● 使⽤前準備
NPB-450 系列NFC版本充電器可使⽤具有NFC功能的智慧裝置透過APP設定
充電曲線等相關參數，使⽤說明及注意事項請參考下文所述。
Android: Android 作業系統4.1(API 16)及以上版本且帶有NFC功能的智慧⼿機
或裝置
iPhone: IOS 12及以上版本的iPhone
● 設定步驟
● APP功能說明
1 讀取及燒錄參數時有無接AC電⼒均可，帶電燒錄參數不會即時⽣效，需斷電重啟
才能⽣效。
2 若忘記燒錄密碼，可通過硬體⽅式恢復出廠設定來重置密碼，具體設定⽅式請參
考NPB⼿冊Page 36關於恢復原廠設定的說明。
APP提⽰當前NFC關閉
請在⼿機或智慧裝置設置中先打開
NFC功能，並重新打開APP
APP提⽰‘無法辨識的機型名稱’
或‘設定失敗’
請更換⽀援NFC功能的⼿機或智慧
裝置後再次嘗試
APP提⽰‘⼿機NFC不可使⽤ ’
請確認NFC天線位置，需縮短感應
距離<5cm內，重新按照Page 1設
定步驟重新進⾏操作
1
43
iOS APP Android APP Android APP
NFC 操作影片
使⽤⼿册
1. 移動裝置或⼿機請先下載明緯APP, 並開啟NFC功能。
2. 請開啟您的移動裝置或⼿機上的NFC。
3. 請先確認⼿機NFC天線位置, 需將⼿機天線靠近NPB側板感應區 (<5公分)。
4. 點選明緯APP→左上⾓選單→安裝⼿冊/APP→Power NFC，點選NFC並靠近
充電器NFC感應位置進⾏讀取。
5. 感應成功後APP會顯⽰功能參數，可依您需求調整相關充電參數。
6. 將⼿機天線靠近充電器NFC感應位置後，點選APP寫入鍵進⾏燒錄。
7. ⼿機顯⽰成功後即完成燒錄。
⼿機或移動裝置需具⽀援NFC功能並且安裝有MEAN WELL APP應⽤程式，如果尚
未在移動裝置上安裝該應⽤程式，請掃描下載：
機型
名稱
1
2
3
4
5
6
7
將設定寫入NPB
充電曲
線參數
系統狀態
可選擇2或3段式充電：3
。 此處按鈕可設定2段式或3段式充電
4 智能偵壓充電模式ON/OFF選擇：
此處按鈕處於ON狀態時，可開啟智慧偵壓模式，充電器會偵測電池電壓，關於
智慧偵壓模式的詳細說明請參考NPB⼿冊Page 36相關內容 ;
若處於 狀態，即處於曲線充電模式，此時充電參數的設定⽣效OFF 。
5 NFC燒錄密碼設定：
出廠時並未設定密碼，使⽤者可⾃⾏設定，密碼最多可設定為8位元，字元需為數
字或英文字⺟（區分⼤⼩寫），不可為特殊字元；密碼設定成功後，後續燒錄操
作前需輸入密碼。
6 CANBus通訊地址設定：
預設通訊位址為0x00；
可設定NPB機型的通訊位址，設定後最多 ⽀援16台設備進⾏CANBus多機通訊，可
可設定位址0～15（0x00~0x0F）；
當定址累加功能處於ON狀態時，後續燒錄的NPB 機型通訊位址會依次累加。
7 返回出廠設定：
點擊原廠預設按鈕，可將NPB相關參數恢復到出廠設定；
燒錄按鈕是每次設定參數後進⾏燒錄的必要操作。
註： . 詳細功能與參數說明請參考 ⼿冊 ~ 。1 NPB page36 42
智能偵壓僅限⽤內建 電池管理系統)之鋰電池。 2. BMS(
1 充電曲線可調：
 此4項為NPB充電CC、CV、FV、TC設定值，可對此處參數進⾏修改，滿⾜實際
充電要求
2 充飽後重啟充電的電壓點設定ON/OFF選擇：
 ON 在重新開啟充電功能按鈕處於 狀態時，在充電完成後，當電池電壓跌落到重
新開啟充電設定電壓值後，NPB會從CC 階段重啟充電進程； 此電壓值可根據實
際應 ⽤情況進⾏設定，必須低於 設定值浮充電壓 。
●注意事項
● 相容的⼿機或移動裝置
● 常⾒問題
狀態 排除⽅法
2
{
{

NPB-450-xxNFC User Manual
Make sure your mobile phone or tablet is equipped with NFC function before
installing the MEAN WELL app. You can get the app from Google Play and App
Store or simply scan the QR codes.
● Before usage:
● Compatibility:
Android devices: requires Android OS 4.1 (API 16) or later
iPhone: requires IOS 12.0 or later
1. Download the MEAN WELL app and activate NFC function if android devices.
2. Open the app and then tap “Power NFC” button to start scanning for
tags.Location of “Power NFC” button: tap the “manual icon” in the upper
left corner on the main page of the app tap “Installation Manual/APP”
button you will see it just sits on the bottom.
3. Hold the device near (< 5cm) the NFC Tag of the charger.
For iPhone, hold the top-center of your phone onto the Tag
For Android, place backside-middle of the phone onto the Tag. If it doesn't
work you may refer to its instruction manual.
4. Upon read, it will bring you to the setup page to let you edit charging
parameters.
5. Tap “Setting button” to update data into the charger after edition.
6. The device will begin scanning for tags again. Hold the device near the NFC
Tag, your device will make a sound and/or vibrate when it is officially encoded.
7. You charger is ready to work.
Note: After completing steps 1-7 above, repeat steps 3-4 again to read and
confirm whether the adjusted charger has truly completed parameter
modifications.
2. If you forget to burn the password, you can
reset the password through the hardware
mode to restore the factory Settings, the
specific setting method, please refer to the
NPB manual Page 36 on restoring the
original factory. Settings;
Open the NFC function in the
Settings of the smart device
and open the APP again.
Please use a smart device that
supports NFC and try again.
Confirm the NFC antenna
position, shorten the sensing
distance(<5cm), and re-operate
according to the steps set on
Page 1.
3 2 or 3 stage charging options:
The button here can set 2-stage or 3-stage charging.
4 Intelligent voltage detection charging mode ON/OFF selection:
Here, when the button is in the open state, the intelligent voltage detection
mode can be turned on, and the charger will detect the battery voltage;
For the detailed description of the smart voltage detection mode, please
refer to the relevant content of NPB manual Page 36;
If it is in the off state, that is, it is in curve charging mode, and the setting of
charging parameters takes effect at this time.
5 NFC burning password setting:
The password is not set before delivery. The user can set the password by
himself. The password can be set to a maximum of 8 characters, and the
characters must be digits or English letters (case sensitive), not special
characters. After the password is set successfully, the password needs to be
entered before the subsequent burning operation.
6 CANBus address setting:
The default communication address is 0x00;
Can set the communication address of NPB model, after setting up to 16
devices to support CANBus multi-machine communication,Can set the
address 0~15(0x00~0x0F);
When the address accumulation function is turned on, the communication
address of the NPB model will be accumulated in turn.
7 Return to factory Settings:
Click the original preset button to restore the NPB parameters to factory
Settings; The burning button is the necessary operation for burning after
each parameter setting.
Note: 1. Please refer to NPB manual page36-42 for detailed function and
parameter description.
2. Intelligent voltage detection is only applicable to lithium batteries
with built-in BMS(Battery management system).
1 2
43
iOS APP Android APP Android APP
● Function Description APP
NFC Video
User's Manual
Model
Name
Write settings to NPB
Charge
curve
parameters
System
Status
1 Charge curve is adjustable :
These four items are set values for NPB charging CC.CV.FV.TC, which can be
modified to meet the actual charging requirements
The APP prompts that
‘The current NFC is closed’.
The app prompts that
‘Unrecognized model name’
or ‘Setting failed’.
The app prompts that
‘Mobile phone NFC is not
available’.
● Frequently Asked Question
State Troubleshooting
● Attention:
1. Read and burn parameters can be AC or not, when the AC is powered on
burning operation, parameters will not take effect immediately, only
power off and restart to take effect.
2 Set the voltage point for restarting the charge after full charging ON/OFF
selection:
When the restart charging button is in the open state, after the completion
of charging, when the battery voltage drops to the restart charging set
voltage value, NPB will restart the charging process from the CC stage; This
voltage value can be set according to the actual application and must be
lower than the FV setting value.
1
2
3
4
5
6
7
{
{
The NPB-450 series chargers with NFC technology are designed to interact
with NFC-enabled mobile devices. This allows users to configure charging
curves and related settings conveniently by using the MEAN WELL app. To
learn more about how to use it, please refer to the following guide.
● How to use: