Meanwell UHP-200A Series User manual

‧
‧
‧
‧
‧
‧
‧
‧
‧
File Name:UHP-200A-SPEC 2022-02-18
UHP-200A series
200W Single Output with PFC Function
■ ■
■
■
‧
‧
‧
‧
Bauar
Sicher heit
egel gema
t gepru ft
od
be
www .
ID 2000000000
tuv.c om
wac g
o s
User’s Manual
■

UHP-200A series
200W Single Output with PFC Function
UHP-200A-4.2
UHP-200A-5
UHP-200A-4.5
File Name:UHP-200A-SPEC 2022-02-18
℃
※ Product Liability Disclaimer:For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
±2.5%
±0.5%
±4.0%
±2.5%
±0.5%
±4.0%
±2.5%
±0.5%
±4.0%
4.0~4.4V 4.3~4.7V 4.7~5.3V
200mVp-p 200mVp-p 200mVp-p
168W 180W 200W
0~40A 0~40A 0~40A
40A 40A 40A
5V4.5V4.2V
2000ms, 200ms/230VAC at full load, 3000ms, 200ms/115VAC at 80% load
10ms/230VAC 10ms/115VAC
PSU Turns on:DC ok; PSU turns off:DC fail
90 ~ 264VAC 127 ~ 370VDC
47 ~ 63Hz
PF 0.97/115VAC PF 0.95/230VAC at full load≥ ≥
88% 88% 88.5%
2.4A/115VAC 1.2A/230VAC
Cold start 85A/230VAC
<1.0mA / 240VAC
110~140% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Hiccup mode, recovers automatically after fault condition is removed
4.6 ~ 6V 5 ~ 6.4V 5.6 ~ 7.1V
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Shut down O/P voltage, recovers automatically after fault condition is removed
-30 ~ +70℃(Refer to “OUTPUT LOAD vs TEMPERATURE")
20 ~ 95% RH non-condensing
-40 ~ +85℃, 10 ~ 95% RH
±0.03%/℃ (0 ~ 50℃)
10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes
UL 62368-1,TUV BS EN/EN62368-1,CCC GB4943, EAC TP TC 004 approved
I/P-O/P:3.0KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC/25℃/ 70%RH
Compliance to BS EN/EN55032 (CISPR32),GB9254,Class A, BS EN/EN61000-3-2,-3,GB17625.1,EAC TP TC 020
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11;BS EN/EN55024, light industry level (surge 4KV),EAC TP TC 020
1949.0 K hrs min. Telcordia SR-332 (Bellcore) ; 211.7K hrs min. MIL-HDBK-217F (25℃)
167*55*26mm (L*W*H)
0.42kg; 20pcs/ 11.4kg/0.76CUFT
DIMENSION
OTHERS
NOTE
MTBF
PACKING
SAFETY &
EMC
(Note.5)
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC IMMUNITY
EMC EMISSION Note.8
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
ENVIRONMENT
OVER TEMPERATURE
OVERLOAD
OVER VOLTAGE
PROTECTION
SHORT CIRCUIT
VOLTAGE RANGE Note.4
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
AC CURRENT (Typ.)
VOLTAGE ADJ. RANGE
DC VOLTAGE
RATED CURRENT
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE TOLERANCE Note.3
RATED POWER
CURRENT RANGE
RIPPLE & NOISE(max.) Note.2
DC OK FUNCTION
SPECIFICATION
MODEL

OUTPUT LOAD vs TEMPERATURE
AMBIENT TEMPERATURE,Ta (℃)
LOAD (%)
(HORIZONTAL)
-30 -25 -10 0 15 30 50 60 70
20
40
60
80
100
STATIC CHARACTERISTIC
INPUT VOLTAGE (V) 60Hz
LOAD (%)
90 110 150 180 200 240 264
100
90
80
70
60
50
40
Block Diagram
PWM CIRCUIT
DETECTION
O.L.P.
EMI
FILTER
APFC POWER
SWITCH-
FILTER
&
SYNCHRONOUS
I/P
FG
ING
CONVERTER
O.V.P.
BRIDGE
RECTIFIERS
O.T.P.
CONTROLLER RECTIFIERS +V
-V
DC OK Function
PFC fosc : 65KHz
PWM fosc : 75~200KHz
100
File Name:UHP-200A-SPEC 2022-02-18
UHP-200A series
200W Single Output with PFC Function

Mechanical Specification CASE NO.: 249A Unit:mm
UHP-200A series
200W Single Output with PFC Function
Pin No.
1
3
2
Assignment
AC/L
AC/N
AC Input Terminal(TB1) pin NO. Assignment
Terminal
4
3
2
1
167
158.5
55
42 6.5
4.25
26
4-ψ3.3 L=6
Function manual
DC OK
V-
CN1
1.Internal circuit of DC ok
1(+)
2(-)
1K
DC Output Terminal(TB2,TB3) pin NO. Assignment
Pin No.
1,2
3,4
Assignment
-V
+V
Terminal
(MW)
TB-HTP-200-40A
Max mounting torque
8Kgf-cm
Pin No.
1
2
Assignment
DC COM
DC OK +V
DC OK Connector(CN1):JST B2B-PH-K-S or equivalent
Mating Housing
JSTPHR-2
or equivalent
Terminal
JSTSPH-002T-P0.5S
or equivalent
Max mounting torque
(DECA)
Contact Close PSU turns on
PSU turns off
10Vdc/1mA
DC ok
Contact Open
Contact Rating(max.)
DC fail
13Kgf-cm
TB1
TB2
TB3
1
2
CN1
1(+)
2(-)
File Name:UHP-200A-SPEC 2022-02-18
CN1
SVR
1
2
3
9.5
8.5

1.Operate with additional aluminum plate
aluminum plate(or the cabinet of the same size) on the bottom.The size of the suggested aluminum plate is shown
as below. And for optimizing thermal performance, the aluminum plate must have an even and smooth surface
In order to meet the“Derating Curve”and the “Static Characteristics” ,UHP-200A series must be installed onto an
Installation
2.For heat dissipation, at least 5cm installation distance around the PSU should be kept, shown as below:
UHP-200A series
200W Single Output with PFC Function
M3*4
380
380
3
unit:mm
5cm
5cm
+V+V-V-V
(or coated with thermal grease), and UHP-200A series must be firmly mounted at the center of the aluminum plate.
File Name:UHP-200A-SPEC 2022-02-18
This manual suits for next models
3
Table of contents
Other Meanwell Industrial Equipment manuals
Popular Industrial Equipment manuals by other brands

McElroy
McElroy Talon 2000 Operator's manual

Bosch
Bosch Rexroth IndraMotion MLC operating instructions

Zoeller
Zoeller MEDIUM X2 operating manual

Reich Kupplungen
Reich Kupplungen ARCUSAFLEX AC F2 Series English translation of the original German Operating Manual

Schmalz
Schmalz SPZ operating manual

HEIDENHAIN
HEIDENHAIN M12 Mounting instructions

M-system
M-system M8DY1 instruction manual

Fröling
Fröling T4e operating instructions

Mitsubishi Electric
Mitsubishi Electric M800VW Series Connection and set up manual

Danfoss
Danfoss S 22 Instructions for installation and use

SYNAPTICON
SYNAPTICON SOMANET Circulo Wiring instructions

Graco
Graco 25T991 Instructions - parts