Meanwell LCM-40TW User manual

Features
Wiring
Environmental limitations
Cautions
Settings and connections
1. Output Current Level Settings
ⅡClass power unit, ungrounded
Full plastic case enclosed
Standby power consumption <0.5W
Protections: Short circuit / Over voltage / Over temperature
5 year warranty
Suitable for intelligent LED lighting
Housing with cable clamp for remote installation
Use wires with an adequate cross-section (see 5)
Use suitable mounting tools to do the wiring and mounting (see 5)
Use a (miniatureMCB circuit breaker) with an adequate current rating to protect the lighting system (see 6)
℃Maximum ambient temperature must not exceed 60
Always allow adequate ventilation clearances, 50mm, around the unit in use to prevent it from overheating
Only install the unit in interior environments
This unit must be installed by a qualified electrician
This unit is not suitable for applications that DC/DC converters are connected before LED lamps
LCM-40TW is a multiple-stage constant driver, selection of output current through DIP switch is exhibited belowpower .
Note : 1.Factory default setting is 700mA.
2.Output voltage and output wattage must not exceed the rated values.
LCM-40TW installation manual
Terminal blocks assignment for LCM-40TW
http://www.meanwell.com
Selectable current
500mA
600mA
800mA
900mA
1
ON
2
----
----
3
ONON
700mA(factory default)
---- ON ----
----ON
1050mA ----
ON
---- ---- ON
ONONON
---- ONON
--------
Status
Single-address DT6
4
----
----
----
5
ONON
ON
Dual-address DT6
Single-address DT8
(factory default)
CH1
CH1,CH2
CH1,CH2
Activatied
Channel
----
ON
----
27-50V
Voltage range
6.75
6.75
68
81.5
6.75 110
123.5
6.75 tc
: Max. Case Temperature
tc
Bottom View
40
15
2- 4.2ψ
+V
AC/L
DA+/PUSH
-V1
AC/N
39.3 65.5
7.8 7.8
4
23
2- 4ψ
TB1
LCM-40TW
+V
-V2
2
3
4
1
TB2
DA-/N
SELV
M M
110
2
EL
25-50V
20-50V
20-50V
20-44V
20-38V
180~277VAC input only
Built-in active PFC
Output current level selectable by DIP switch
Built-in DALI interface and push dimming function
Available for DALI device type 6(DT6) and device type 8(DT8)
Tunable White control
Constant po er mode output ith 2 channels
Minimum dimming level 0.2%
Emergency lighting (EL) available
MEAN WELL
2022/6/8
ISSUE

3. Connection of Dimming Functions
4. Recommended Screwdriver, Wire and Torque Setting
5. Suggested Maximum Number of the LCM Units that can be Connected to a MCB (miniature circuit breaker) at 230Vac
Note: These calculated values are based on MCB S201 series manufactured by ABB.
http://www.meanwell.com
Type
Model B10 B16 C10 C16
LCM-40TW15262744
Solid wire
Stranded wire
American wire gauge
Wire stripping length
Screwdriver
Recommended tightening torque
Suggested push-down strength
-----
-----
-----
-----
6mm Phillips
4.6 kgf-cm (4 lb-in)
-----
The cover
(the blue one)
Push terminal
(ACL/N, PUSH, DA , Vo )
±±
ψψ1.024 - 1.628mm
0.823 - 2.08mm2
14 - 18AWG
10mm (0.39")
3mm Phillips
-----
3 - 4 kp (6.61-8.81 lb )
F
a. DALI
Note : Maximum DALI cable length is 300m
(based on a 1.5mm or 14AWG cable)
2
DALI
controller
b. Push dim
Note: ONLY use open push button without indicator light.
Push Button
LINE (Brown or black)
NEUTRAL (Blue or white)
Warning: Risk of short circuit. The push button can only be linked between the PUSH and the AC/L (brown or black).
DO NOT connect the push button to the AC/N (blue or white).
ψψ0.404 - 0.643mm
0.129 - 0.326mm2
22 - 26AWG
7mm (0.27")
3mm Phillips
2.88 kgf-cm (2.5 lb-in)
-----
Screw terminal
(FAN , NTC , DIM )
±±±
Dimming control mechanism
Function
Turn ON/OFF
Dim UP/DOWN
Reset
None
Pushing time
0.1 ~ 1 sec
1.5 ~ 10 sec
> 11 sec
< 0.05 sec
Every long pushing action will change the dimming direction.
Factory dimming setting: 100%
2. Connection of LED Lamps
Press down the "push button" by a slotted screw driver to insert or remove the cable.
-V1
+V
AC/N
AC/L
NEUTRAL (Blue or white)
LINE (Brown or black)
+V
Two independent output control(DT6)
CH2
(Warm white)
CH1
(Cool white)
Tunable white control(DT8)
DA+/PUSH
AC/N
AC/L
DA-/N
DA+/PUSH
AC/N
AC/L
DA-/N
-V2
-V1
+V
+V
-V2
AC/N
AC/L
NEUTRAL (Blue or white)
LINE (Brown or black)
LINE (Brown or black)
NEUTRAL (Blue or white)
MEAN WELL
2022/6/8
ISSUE