Meanwell LCM-40DA User manual

Features
Wiring
Environmental limitations
Cautions
Settings and connections
1. Output Current Level Settings
180~295VAC input only
Built-in active PFC
Output current level selectable by DIP switch
Built-in DALI interface and push dimming function
Power supply synchronization function up to 10 units
ⅡClass power unit, ungrounded
Full plastic case enclosed
No load power consumption <0.5W
Protections: Short circuit / Over voltage / Over temperature
3 year warranty
Suitable for intelligent LED lighting
Housing with cable clamp for remote installation
Use wires with an adequate cross-section (see 5)
Use suitable mounting tools to do the wiring and mounting (see 5)
Use a (miniatureMCB circuit breaker) with an adequate current rating to protect the lighting system (see 6)
℃Maximum ambient temperature must not exceed 60
Always allow adequate ventilation clearances, 50mm, around the unit in use to prevent it from overheating
Only install the unit in interior environments
This unit must be installed by a qualified electrician
This unit is not suitable for applications that DC/DC converters are connected before LED lamps
The LCM can provide various output currents by setting the DIP switch. The settings of the DIP switch are shown in the tables below.
LCM-40DA(2) LCM-60DA(2)
Note : 1.Factory default setting is 700mA.
2.Output voltage and output wattage must not exceed the rated values.
Voltage
range
Voltage
range
112233445566
Selectable
Current
Selectable
Current
2-100V 2-90V--- ------ ------ ------ ------ ------ ---
--- ------ ------ ------ ------ ---
--- ------ ---
--- ---
--- ---
--- ---
--- ---
--- ---
ON ON
ON ONON ON
ON ONON ONON ONON ON
ON ONON ONON ONON ONON ON
ON ONON ONON ONON ONON ONON ON
350mA 500mA
2-80V 2-90V500mA 600mA
2-67V 2-86V
600mA 700mA*
2-57V 2-67V700mA* 900mA
2-45V 2-57V900mA 1050mA
2-40V 2-42V1050mA 1400mA
LCM-40DA(2), LCM-60DA(2) installation manual
ON
6 5 4 3 2 1
-Vo
+Vo
SYN.
+
+
DA-
DA+
PUSH
AC/N
AC/L
a. Terminal blocks assignment for LCM-40/60DA
2. Connection of LED Lamps
Press down the "push button" by a slotted screw driver to insert or remove the cable.
Vo-
Vo+
AC/N
AC/L
NEUTRAL (Blue or white)
LIVE (Brown or black)
http://www.meanwell.com
123.5mm 23mm
81.5mm
IS 15885(Part 2/Sec13)
R-41027766
THOMASSAMUEL
THOMASSAMUEL
(for DA-Type only)
2
(for DA2-Type only)
(except for DA2-Type)(except for DA2-Type)
SELV
M M
110
EL
ON
6 5 4 3 2 1
-Vo
+Vo
SYN.
+
-NTC
+NTC
-FAN
+FAN
+
DA-
DA+
AC/N
AC/L
b. Terminal blocks assignment for LCM-40/60DA2
123.5mm 23mm
81.5mm
-NTC
+NTC
-FAN
+FAN

3. Connection of Dimming Functions
4. NTC Connection
5. Recommended Screwdriver, Wire and Torque Setting
6. Suggested Maximum Number of the LCM Units that can be Connected to a MCB (miniature circuit breaker) at 230Vac
a. DALI (DA version only)
c. Push dim (DA version only)
d. Synchronization operation
Note: ONLY use open push button without indicator light.
Warning: Risk of short circuit. The push button can only be linked between the PUSH and the AC/L (brown or black).
DO NOT connect the push button to the AC/N (blue or white).
b. DALI2 (DA2 version only)
Note : Maximum DALI cable length is 300m
(based on a 1.5mm or 14AWG cable)
2
DA+
DA- DALI
controller
Dimming control mechanism
Function
Turn ON/OFF
Dim UP/DOWN
Reset
None
Pushing time
0.1 ~ 1 sec
1.5 ~ 10 sec
> 11 sec
< 0.05 sec
Note: These calculated values are based on MCB S201 series manufactured by ABB.
http://www.meanwell.com
Type
Model B10 B16 C10 C16
LCM-40DA(2) 15 26 27 44
LCM-60DA(2) 15 25 27 32
Solid wire
Stranded wire
American wire gauge
Wire stripping length
Screwdriver
Recommended tightening torque
Suggested push-down strength
-----
-----
-----
-----
6mm Phillips
4.6 kgf-cm (4 lb-in)
-----
The cover
(the blue one)
Push terminal
(ACL/N, PUSH, DA , Vo )
±±
ψψ1.024 - 1.628mm
0.823 - 2.08mm2
14 - 18AWG
10mm (0.39")
3mm Phillips
-----
3 - 4 kp (6.61-8.81 lb )
F
NTC-
NTC+
AC/L
AC/N
Push ButtonPUSH
LIVE (Brown or black)
NEUTRAL (Blue or white)
ψψ0.404 - 0.643mm
0.129 - 0.326mm2
22 - 26AWG
7mm (0.27")
3mm Phillips
2.88 kgf-cm (2.5 lb-in)
-----
Screw terminal
(FAN , NTC , DIM )
±±±
Every long pushing action will change the dimming direction.
Factory dimming setting: 100%
NOTE 1. Please make sure all units are set to 100% dimming setting (factory default) before synchronizing.:
2. For optional EO model: the master is EO and the salve could be standard model for economic arrangement.
3. Min. Dimming operating range depends on dimmer setting.
Synchronization up to 10 drivers (1 master + 9 slaves)
Dimming operating range : 10%~100%
Sync cable length : < 5m
Sync cable type : Flat cable
Sync cable cross section area : 22 – 24 AWG (0.2~0.3mm )
2
------
+
+
+
+
+
+
SYN. SYN. SYN.
Master Slave 1
5m 5m
DA+
DA- DALI
controller
d. Push dim (DA2 version only)
AC/L
AC/N
Push Button
LIVE (Brown or black)
NEUTRAL (Blue or white)
DA+
DA-