Mediclinics M99A-UL User manual

HAND DRYERS / SECADOR DE MANOS / SÉCHE-MAINS
M99A-UL / M99AC-UL / M99ACS-UL
M88APLUS-UL
INSTALLATION AND OPERATING MANUAL
MANUAL DE INSTALACIÓN Y UTILIZACIÓN
MANUEL D’INSTALLATION ET D’UTILISATION

-2-
Machine must be handled only by an autorized technician.
WARNING: When dismantle the cover, electrical live and basic insulated parts are accesible.
Figure 1
Technical Features:
• Surface Mounted.
• Sensor Operated - Adjustable Detection Range: 2-6 inches (5-15 cm).
• Voltage: 110 - 120 Volt at 60 Hz.
NOTE: For dryer to function properly, a minimum of 15 inches (40 cm) should be spaced between
the hand dryer sensor and any obstruction such as shelves, hand washing stations, or any type of
reflective surface.
1.Dismantling for installation
• The dryer is supplied with a pressure-mounted
cover and is not screwed down.
• The 4 attachement screws are provided in the
plastic bag with the plugs and lag bolts.
• Remove cover vertically, taking care
to avoid:
- Damaging internal components.
- Damaging cover (See Figure 1).
2.Mounting
• Mount the machine along the rear channels.
• Insert the electric ducting through the hole next to the terminal strip.
• Use the drill template provided to fix the dryer to the wall.
• Drill 4 holes with a diameter of 5/16” (8 mm), and take care to clean all traces of dust from the
holes.
• Screw down the base firmly to the wall using an screwdriver.
• Connect the electric ducting to the terminal strip. Screw down the 3 locking screws firmly.
• Finally close the terminal block cover properly
.
INTRODUCTION
ENGLISH
INSTALLATION
MACHINE SHOULD BE INSTALLED, SERVICED AND MAINTAINED BY A QUALIFIED
TECHNICIAN
Figure 2

www.mediclinics.com
-3-
Figure 5
3.Sensor range adjustment
Disconnect power to perform adjustments.
These adjustments should be made by a
qualified technician.
Default Setting:
• Detection Range: Low.
Description
Reference
number
Mediclinics’ part
number
Fan Wheel
1
RC92239T
Motor
2
RC92639-UL
Heating element
3
RC92637-UL
Sensor
4
RC92610-UL
Figure 3
Sensor range
High (8-10 inches)
Low (4-6 inches)
WIRING DIAGRAM
BREAKDOWN LIST OF BASIC PARTS

-4-
To dry correctly is recommended rising well to remove all traces of
soap.
These models operate by hand detection. Place hands 4-6" (10 - 15
cm) from the air outlet and the dryer will start working. Once activated,
immediately place hands in air flow and rub together until dry.
This machine will stop 2-3 seconds after use.
If the sensor is blocked due to vandalism, the dryer will completely stop
working.
NOTE: let a minimum separation of 15” (40 cm.) between appliance
and any shelf, marble, worktop or washbasin.
1. Preventative maintenance
Correct cleaning of the unit will lengthen its working life considerably. When in use, the
machine will accumulate dust inside which should be cleaned out every six months.
2. Cleaning method
1. Turn off power to the unit.
2. Remove cover using security wrench (See Dismantling for Installation).
3. Clean away any accumulated dust on the fan with a soft bristle brush while rotating it
manually. Use the same brush, to clean away all accumulated dust from the other
components. Carefully remove any dust from the electronic circuit board and hand
detecting sensors using a fine brush.
4. Use brush to clean the air inlet grill and make sure the LED visor is completely clean.
6. Reconnect power to the unit and let it run continuosly, removing any excess dust.
7. Turn off power to the unit and install cover per the Mounting Instructions.
Cleaning the cover - Use only a wet cloth to clean the covers. Do not use any kind
of detergent, acids, lye, abrasives, hydrocloric acid, etc.
PREVENTATIVE MAINTENANCE AND CLEANING
METHOD OF USE
Caution: Do not damage or force any components.
Figure 6
Sensor
Sensor

www.mediclinics.com
MODEL
MODELO
MODÈLE
M99A-UL
M99AC-UL
M99ACS-UL
MM88APLUS-
UL
GENERAL:
GENERAL:
GÉNÉRAL :
Input voltage:
Alimentación:
Alimentation :
110 –120 VAC / 60Hz
Consumption:
Consumo:
Consommation :
13.6 A
Rated power:
Potencia nominal:
Puissance nominale :
2.25 Hp (1,680 W)
Weight:
Peso:
Poids :
9.8 lb
(4,45Kg)
9.4 lb (4,25Kg)
6.6 lb (3 Kg)
MOTOR:
MOTOR:
MOTEUR :
Power:
Potencia:
Puissance :
1/4 Hp (180 W)
Type:
Tipo:
Type :
Shaded pole motor / Jaula de ardilla / À bague de
déphasage
TURBINE:
TURBINA:
TURBINE :
Single inlet centrifugal fan / Centrífuga de entrada
simple / Centrifuge à un orifice
HEATING
ELEMENT:
RESISTENCIA:
RÉSISTANCE :
Power:
Potencia:
Type :
2 Hp (1,500 W)
TIMER:
SENSOR:
CAPTEUR :
Type:
Tipo:
Puissance :
IR Sensor / Sensor IR / Capteur IR
DIMENTIONS:
DIMENSIONES:
DIMENSIONS :
Height:
Alto:
Hauteur :
13” (302 mm)
Width:
Ancho:
Largeur :
10.2” (260 mm)
Depth:
Profundo:
Profondeur :
5.9” (150 mm)
CASING:
CARCASA:
CAPOT :
Material:
Material:
Matière :
Steel
/Acero /
Acier
Stainless Steel / Acero
inoxidable / Acier inox
Plastic (ABS)
Thickness:
Espesor:
Épaisseur :
0.06“ (1,5 mm)
0.12” (3 mm.)
Finish:
Acabado:
Finition :
White
paint /
Pintado
blanco /
Peinture
blanche
Bright /
Brillante /
Brillant
Satin /
Satinado /
Satiné
White
APPROVALS:
HOMOLOGACIONES:
HOMOLOGATIONS :
UL - CSA
AIR OUTPUT:
SALIDA AIRE:
SORTIE D’AIR :
Air flow:
Caudal de aire:
Débit d’air :
127 CFM (3,590 l/min)
Air speed:
Velocidad del aire:
Vitesse de l’air :
2,734 LFM (50 Km/h)
Air temperature:
Temperatura del aire:
Température de l’air :
135 ºF (57 ºC)

ANNEX
MOUNTING INSTRUCTIONS.
To mount onto wall, be sure there are no hidden electrical circuits or pipes in the
mounting location.
Place the mounting template (provided) on the wall to mark location of four mounting
screw holes.
Drill four holes (Fig.1) Ø8 (5/16”) diameter and 45mm (1 ¾”) depth.
Take off the residual dust from the holes.
Insert nylon plugs (provided) into four holes (Fig.2-3).
Place base plate on wall (Fig.4).
Fix the base plate firmly on the wall (Fig.5-6).
MOUNTING ITEMS PROVIDED.
4 screw.
4 Plug.
1 Mounting template.
1 Instruction manual.
NYLON PLUG D8