Mediclinics M88-UL User manual

HAND DRYERS
INSTALLATION AND OPERATING MANUAL
M88-UL / M88A-UL / M89A-UL
04 / 04
www.saniflowcorp.com
USA
SANIFLOW CORPORATION
2655 LeJeune Rd.,
Suite 810. Coral Gables, FL 33134.
Tel.: [phone]
Fax: [phone]
[email protected]
www.saniflowcorp.com
SPAIN
MEDICLINICS, S.A.
Industria, 54
E-08025BARCELONA
Tel.: [phone]
Fax: [phone]
[email protected]
www.mediclinics.com
Cod.: 92915UL

6
www.saniflowcorp.com
Mounting
1
INSTALLATION
Dismantling for installation
• The dryer is supplied with a pressure-mounted cover, and is not screwed down.
• The 4 attachment screws are provided in the bag with the plugs and lag bolts.
• Remove the cover vertically from the machine supporting base, taking care to avoid:
- Damaging the internal components.
- Damaging the cover. We recommend resting it on a flat surface with the visible part upwards, or on
top of a cloth.
• Mount the machine along the rear channels.
• Insert the electric ducting through the hole next to the terminal strip.
• Use the drill template provided to fix the dryer to the wall.
• Drill 4 holes with a diameter of 5/16” (8 mm), and take care to clean all traces of dust from the holes.
• Screw down the base firmly to the wall using a flat ended screwdriver of 1/4" (6÷7 mm).
• Connect the electric ducting to the terminal strip. Screw down the 3 locking screws firmly.
Hole for the insertion of the electric ducting.
CAUTION: do not damage the ir sensors in automatic models

5 2
www.saniflowcorp.com
H - Heating element
M - Motor
S - Sensor
P2 P3
WIRING DIAGRAM
Models with pushbutton
Automatic models SENSOR RANGE
High Low
T
Connection to P.C. Board.
Connection to P.C. Board.
Fan wheel
Motor
Heating element
Sensor
Timer
1
2
3
4
5
120V
Code RC92239T
Code RC92239-UL
Code RC92237-UL
Code RC92710-UL
Code RC92725-UL
5
4
BREAKDOWN LIST OF BASIC PARTS
This Product covered by this limited warranty is warranted to be free
from defects in material and workmanship under normal conditions
for a period of five years from the date of purchase.
The manufacturer’s obligation under this Limited Warranty is applicable
only where a product defect has been claimed during the warranty
period. The manufacturer’s obligation under this Limited Warranty is
limited to either (I) replacement of the Product; or (II) replacement
of defective parts. To claim under this Limited Warranty, contact one
of Mediclinics, S.A. official dealers.
Mediclinics, S.A. shall not be responsible for any other damage, including,
but not limited to, any defects or damage caused by or resulting from:
(a) alterations to the product; (b) use of the product in an incorrect
manner or for an unreasonable use; (c) failure to use the product in
a safe and reasonable manner, and (d) repair of the product by
unauthorized personnel.
LIMITATION ON LIABILITY
THE WARRANTY SET FORTH ABOVE IS EXCLUSIVE AND NO OTHER
WARRANTY, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED.
MEDICLINICS, S.A. SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL MEDICLINICS, S.A. BE LIABLE FOR INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF CUSTOMERS, LOSS
OF USE, DAMAGE TO GOODWILL OR TO BUSINESS REPUTATION) OR
FOR ANY OTHER LOSSES FROM ANY CAUSE, INCLUDING DAMAGES
CAUSED BY THE PRODUCT, WHETHER OR NOT MEDICLINICS, S.A. HAS
RECEIVED NOTICE OF THE POSSIBILITY OR CERTAINTY OF SUCH
DAMAGES OR LOSSES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
LIMITED WARRANTY
WARRANTY · WARRANTY · WARRANTY · WARRANTY
GARANTIA · WARRANTY · GARANTIE · GARANZIA
WARRANTY · WARRANTY · WARRANTY · WARRANTY · WARRANTY · WARRANTY ·
WARRANTY · WARRANTY · WARRANTY · WARRANTY · WARRANTY · WARRANTY ·
H - Heating element
M - Motor
T -Timer
G
G
H
H
H H
H H
1
2
3

4
www.saniflowcorp.com
METHOD OF USE
Correct cleaning of the machine will lenghten its working life considerably.
When in use, the machine will accumulate dust inside which should be cleaned out if used regularly,
at least ONCE A YEAR.
PREVENTATIVE MAINTENANCE AND CLEANING
1. Disconnect the dryer lead-in wire.
2. Unscrew the 4 side attachment screws using a Phillips
screwdriver.
3. Remove cover (See dismantling for installation).
4. Remove the accumulated dust in the fan wheel with a
soft bristle brush.
5. Using the same brush, remove the dust accumulated in
the out grill.
6. Brush the sides between the support and the wall.
7. We recommend removing the machine from the wall and
unscrewing the four mounting bolts to remove any
obstructions (paper, cigarette ends, etc.)
Machine must be handled only by an autorized technician.
WARNING: When dismantle the cover, electrical live and basic insulated parts are accesible.
To dry hands correctly, we recommend rinsing well to remove all traces of soap. Once the dryer is working, hold
the hands at an approximate distance of 2.5”÷3” (6÷7 cm) and rub together. The hands can be gradually taken
away from the dryer and will continue drying up to a maximum distance of 4"÷6" (10÷15 cm).
Automatic models:
These models operate by hand detection. If hands are held 4"÷6" (10÷15 cm) from the air discharge nozzle,
the dryer will start working and will stop 2÷3 seconds after use.
If the sensor is blocked due to vandalism, the dryer will completely stop working.
Please, concerning automatic models, let a minimum separation of , 16” (40 cm) between appliance and any
shelf, marble, worktop or washbasins.
Pushbutton Sensor
CLEANING METHOD
3
M88-UL M88A-UL M89A-UL
110-120V 50/60 Hz
11A
1.7Hp (1300 W)
6.616 lb (3 kg) 8.316 lb (3,75 Kg)
1/7Hp (100 W)
Shaded pole Motor
Single inlet centrifugal fan
1.6Hp (1200 W)
Timer IR Sensor
45 s _
11.8” (300 mm)
9.8” (250mm)
5.1” (130mm)
ABS Aluminium
UL 499
140 CFM(4000 l/min)
3,900 LFM(71 Km/h)
124 º F(51ºC)
MODEL
Input voltage
Consumption
Rated power
Weigth
MOTOR:
Power
Type
SCROLL-FAN
HEATING ELEMENT:
Power
TIMER:
Type
Drying cycle
DIMENSIONS:
Height
Widht
Depth
COVER:
Type
Certified in accordance with:
Air flow
Air velocity
Air temperature
Caution: do not damage or force any machine part.
8. When maintenance is complete, screw the base to the
wall (if applicable), re-mount the cover, tighten up the
screws and plug in.
9. Incase of havingdismantled the air outlet,install it again
in its place and ensure that it is in its proper position
10. Switch on the machine and leave running until all traces
of dust from the cleaning proces have been discharged
from the air stream.