MEGATRONIX Megalarm MEGA 2500 User manual

MEGA 2500 OPERATE
1
MEGA 2500
2-WAY LCD 4-CHANNEL
CAR ALARM SECURITY SYSTEM
Operation Manual
MEGATRONIX
CALIFORNIA, U.S.A.

MEGA 2500 OPERATE
2

MEGA 2500 OPERATE
3
OPERATION:
A.TRANSMITTER OPERATION:
Transmitter Button
System Function
Remark
Lock Doors and Arm System
-
Arm and Delete the 2 Stage Shock Sensor
Press twice within 3 seconds
- -
Arm and Noiseless Mode
Press within 3 seconds
-
Arm System and Hidden Alarm Function
Press within 3 seconds
+
Silent Arming / Disarming
Ignition in "off" position.
+ (2-second)
Active Anti Car-Jacking Mode
Ignition in "on" position press and
hold for 2 seconds
Unlock Doors and Disarm System
-
2-Step Door Unlock and Disarm System
Press twice within 3 seconds
(2-second)
Trunk Release (Channel 3)
Press and Hold for 2 seconds
-
Passive Arming By-pass
While the system is disarmed
- -
Remote Control Entry/Exit Valet Mode
While the system is disarmed
Press within 3 seconds
+
Channel # 4 Timer Output
Car Locator
(3-second)
Panic function
Press and Hold for 3 seconds
B. 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION ONLY:
Transceiver Button
System Function
Remark
F - (C)
System’s Trigger Check
Press within 3 seconds
F - F-(C)
System’s Status Check
Press within 3 seconds
F - ( )
Optional Driving Pager
Press within 3 seconds
F(1 second)
LCD screen lamp turns on for 5 seconds.
Press and hold for 1 second
F- F- F
Clear the Flash Icon and Melody Sound on
the LCD Screen Transmitter
Press within 3 seconds
C.LED INDICATORS:
LED
Status
LED
Status
Off
Disarmed
2 flashes... pause
Zone 2 / Trigger on Trunk/Hood
Slow flash
Armed
3 flashes... pause
Zone 3 / Trigger on Door Switch
Fast flash
Passive arming
4 flashes... pause
Zone 4 / Trigger on Shock Sensor
On (solid)
Valet mode
5 flashes... pause
Zone 5 / Trigger on Ignition Switch
D. CHIRP INDICATORS: E. PARKING LIGHT:
Chirp
Function
Parking light
Function
1 chirp
Arm
1 flash
Arm
2 chirps
Disarm
2 flashes
Disarm
3 chirps
Ajar Warning
3 flashes
Triggered
6 chirps
Car locator
12 flashes
Car locator
F. SYSTEM OPERATING CONDITION:
Siren, Horn
Parking Light
LED
Doors
Starter
Dome Light
1. Arming
1 or 3 Chirps
1 Flash
Slow Flash
Locking
Disable
2. Disarming
2 or 4 Chirps
2 or 3 Flashes
Fast Flash or
Off
Unlocking
Turns on for
30 -second
3. Trigger
Alarming
Flashes
Slow Flash
Disable
Flashes
4. Panic
Alarming
Flashes
Flashes
5. Car-Jacking
Alarming
Flashes
Disable
Flashes
6. Car Locator
6 Chirps
12 Flashes

MEGA 2500 OPERATE
4
G. ACTIVE ARMING –LOCK & ARM:
1. Press button on the transmitter.
2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The
vehicle doors will lock upon arming when interfaced with the security system.
System Arm
Door Ajar
Trunk / Hood Ajar
Clear The Flash Icon:
Press the Fbutton 3
times within 3 seconds
will clear the flash icon on
the LCD screen
transceiver.
AJAR WARNING: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. (See
Alarm Feature “I - 3 Programming)
SILENT ARMING / DISARMING: Press the and buttons at the same time on the transmitter will
arm or disarm your security system, No chirp sounds will be heard, arm / disarm confirmation will be
through the vehicles parking lights only.
SHOCK SENSOR BY-PASS: Press the button on the transmitter twice within 3 seconds will arm the
security system and bypass the shock sensor. The system will chirp one additional time to confirm the
sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming
cycle only. The security system will return to normal operation during the next arming cycle.
NOISELESS MODE: Press button once. The siren chirps once, The system is now armed.
Press the button twice more within 3 seconds: The siren chirps once again, the system is now in
Noiseless mode. On this mode, for the zone 4 shock sensor, the trigger timer will reduced from 30
seconds to 15 seconds.
The noiseless feature is programmed to activate for one arming cycle only. The security system will return
to normal operation during the next arming cycle.
HIDDEN ALARM FUNCTION: Press the button first; within 3 seconds press the button to
activate the hidden alarm function. The security system will arm and with “Hidden Alarm Function”. The
siren / horn will be silenced even if the sensor is triggered in the armed status.
H. PASSIVE ARMING: (See Feature “II - 2” Programming):
Active arming / disarming will allow you to control your security system via the remote transmitter. This
security system is equipped with an optional Passive Arming feature, which allows the security system to
arm 30 seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any
door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once the
vehicle all entrances are closed.
3. After 30-second time has elapsed, the security system will automatically “ARM”. The siren will chirp [1]
time and the parking lights will flash [1] time and remain on for 10-seconds.
PASSIVE DOOR LOCKING: (See Feature “II - 2” Programming)
The vehicle doors will automatically lock after passive arming cycle has been completed.
PASSIVE ARMING BY-PASS: While the system disarmed, Press the button twice, the security
will respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporally state
for as long as you wish. To exit passive by-pass, press the transmitter or button and the system
will return to normal status.
I. ACTIVE DISARMING –UNLOCK & DISARM:
1. Press button on the transmitter.
2. The siren will chirp twice and parking light will flash twice and then remain
on for 30 seconds indicating that the security system is now disarmed. The
vehicle doors will unlock and dome light wills turns on for 30 seconds upon
disarming when interfaced with the security system.
System Disarm

MEGA 2500 OPERATE
5
CLEAR FLASH ICON: Press Fbutton 3 times within 3 seconds will clear flash icon on LCD screen.
TAMPER DISARMING: If alarm triggered, upon disarming, siren chirp 4 times, parking light flash 3 times.
PATHWAY ILLUMINATION (See Alarm Feature “II - 4” Programming): This feature turns the parking
light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal.
TWO STEP DOOR UNLOCK: This feature will independently unlock drives door only when disarming
security system. Pushing button on transmitter second time within 3 seconds will unlock entire vehicle.
AUTOMATIC RE-ARM (See Feature “I - 2” Programming): If this feature is selected, the security system
will automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will
cancel if any door is opened before the 60 seconds timer has elapsed.
J. DISARMING WITHOUT A TRANSMITTER:
OVERRIDE THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting):
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch.
Alarm will stop sounding and enter disarm mode. You can now start and operate the vehicle normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE: (Alarm Feature IV - 2Programming)
Unlike valet switch easily found, and defeated, this security system allows the consumer to program a
password pin code, offering a higher level of security.
1. Enter the vehicle and turn the ignition switch to the 'ON’ position. (Alarm will sound.)
2. Within 5 seconds, enter your chosen first 10ths digit by pressing and releasing the valet switch.
3. Within 15 seconds of the last entered 10ths digit, turn the Ignition switch “OFF” then “ON”.
4. Within 15 seconds, enter your chosen second 10ths digit by press and release the valet switch.
5. Turn the ignition switch “OFF” position.
[4] Chirps form siren/horn, [3] flash from parking light and LED will turn off to indicate system disarmed.
Note 1: You must override the alarm within 60 seconds. If not, the system will automatically re-arm.
EXAMPLE: To Override The System With The Password Code 83, you would;
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 5 seconds, press and release the valet switch 8 times
3. Within 15 seconds of the last entered 10ths digit, turn the Ignition Switch “Off” then “ON”.
4. Within 15 seconds, press and release the valet switch 3 times
5. Turn the Ignition Switch to “Off” position.
[4] Chirps form siren/horn, [3] flash from parking light and LED will turn off to indicate system disarmed.
K. VALET MODE: (System in Disarm or Valet mode):
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm
functions are bypassed, however the remote panic feature and remote door locks will remain operational.
To use the valet mode, the system must first be disarmed either by using your remote transmitter, or by
operating the Manual override sequence.
Enter Valet Mode:
1. From the disarmed condition, turn the ignition to the
“ON” position.
2. Push and hold the valet switch for 2 seconds until the
LED turns on. The LED will remain on as long as the
system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'on'.
2. Push and hold valet switch for 2 seconds. LED will
turn off indicating system has exited valet mode.
Remote Door Lock
Remote Door Unlock
Parking light flash to confirm enters valet mode and two parking lights flash to confirm exit valet mode.
Remote Valet Mode:
1. Press and release button on transmitter three times within 3 seconds to enter or exit valet mode.
2. One parking light flash will confirm you have entered ‘valet mode’ and two parking light flashes will
confirm you exited ‘valet mode’.
L. CAR LOCATOR:
Press the button to activate car locator function. The siren will chirp 6 times. The
parking light will flash 12 times, for you to easily locate your car.

MEGA 2500 OPERATE
6
M. PANIC FUNCTION: (See Alarm Feature V –4 Programming):
The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.
1. Press and hold the button for 3 second. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be suspended.
The and buttons can be used to lock and unlock the doors (if the option is
installed), however once the button is pressed, the vehicle’s starter disable
device, (where installed) will be enable allowing the vehicle to start.
3. To stop the alarm, press and hold the button on the transmitter again for 3
seconds. Also if any transmitter button other than or or button is pressed
and released, the panic mode will be turned off immediately.
4. If the button is not pressed, the alarm will automatically stop after 30 seconds.
N. TRIGGER THE SYSTEM:
When armed, your vehicle is protected as follows:
1. Light impacts will trigger the warn-away signal.
2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition key will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking
lights, and dome light will turn on to alert of an intrusion for 30 seconds. Then it will stop and automatic
reset and re-arm. If the one of sensors or detectors is still active, the alarm system will sound a maximum
of 6 times of 30 seconds cycles.
Trunk
Trigger
Doors
Trigger
Shock Sensor
Trigger
Ignition
Trigger
Warn-away
Trigger
Hood
Trigger
STOP THE MELODY SOUND ONLY: While triggering the alarm the LCD screen will alert user through
melody sound and flashing trigger icon, press any button on the LCD remote transceiver to stop melody
sound only
CLEAR THE FLASH ICON AND MELODY SOUND: While triggering the alarm the LCD screen will alert
user through melody sound and flashing trigger icon, press the Fbutton 3 times within 3 seconds will
clear the flash icon and stop melody sound on the LCD screen transceiver.
NOISE ABATEMENT CIRCUIT: Your system has “Noise Abatement Circuit”. It prevents annoying
repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder,
jackhammers, airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time the same sensor or
switch is triggering the alarm, the “Noise Abatement Circuit” will interpret this pattern of triggers or false
alarms. After the fifth trigger, “Noise Abatement Circuit” ignores, or by pass, that sensor or switch until the
other sensor or switch is trigger.
“Noise Abatement Circuit” covers doors, hood, and trunk differently: If the alarm is triggered by an open
door for six full cycles (three minutes), the doors will be bypassed until the trigger ceases.
O. ANTI CAR-JACKING:
Warning: If you do not need the carjacking function in this alarm system, be sure to set car-jacking
feature “OFF”. The default setting for this system is all carjacking “OFF”. (See Alarm Feature I –4
Programming).
ACTIVE ANTI CAR JACKING:
1. Press and hold the transmitter and buttons at the same time for 2 seconds while the vehicle’s
ignition is ON. The parking lights will turns on for 1.5 seconds to indicate the system enters the
car-jacking mode.
2. Once the system in car-jacking mode, if you are forced from the vehicle, the system will be trigger
when the door is opened and closed while the ignition is “ON”.
PASSIVE ANTI CAR-JACKING:
1. Turn the ignition switch to “ON” position; the system enters the car-jacking mode.
2. Once the system in car-jacking mode, if you are forced from the vehicle, the system will trigger when
the door is opened and closed while the ignition is “ON”.
TRIGGER THE ANTI CAR-JACKING MODE:

MEGA 2500 OPERATE
7
a). 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.
b). During this 15 seconds period of chirping, are being alerted to push the valet switch once to turn off
the car-jacking feature. If not, it will enter the second timer carjacking.
c). 65 seconds after system has been triggered, siren starts alarming and parking light starts flashing.
d). 90 seconds after the system has been triggered:
1. The siren will continue alarming and the parking lights flashing, and
2. The starter disable will activate to prevent the vehicle from starting.
3. It will remain active until the vehicle's battery power is exhausted.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and
the system disarmed.
Note: If you use password pin code to protect vehicle security, you will need to use it to disarm system.
P. SYSTEM’S TRIGGER CHECK: (For two-way transceiver operation only):
Press the transceiver Fbutton first, within 3 seconds press (C) button. It responds
with one melody sound and all trigger’s records will immediately be displayed on the LCD
screen.
Q. SYSTEM’S STATUS CHECK: (For two-way transceiver operation only):
When you want to check the system’s present status through the LCD screen, press the
transceiver Fbutton twice. Within 3 seconds press (C) button. It will respond with
one melody sound. The LCD screen should be illuminated.
R. DRIVER PAGING: (For two-way transceiver operation only):
It is useful the event that someone wants to page the driver of the parked vehicle or
someone cannot find his LCD remote control transceiver.
Indoor Driving Paging:
With ignition switch “OFF”, press and hold the valet switch for 2 seconds to page the
driver, one chirp sound shall be emitted from the vehicle and the paging melody sound
continues on your remote LCD transceiver and “ ” indication flashes on the LCD
screen.
Outdoor Driving Paging:
If someone tries to page you by tapping the paging (knock) sensor (optional) which is
usually mounted on the bottom part of front window, the paging melody sound continues
sounding from your Remote LCD transceiver and “ ” indication flashes on the LCD
screen.
1. Press the transmitter Fbutton first, within 3 seconds press () button to activate
outdoor driver paging function, It responds with chirps of the vehicle, a melody sound
and " " indication flashes on the LCD screen to confirm the function is on.
2. When tapping the paging (knock) sensor, one chirp sound shall be emitted from
the vehicle and the paging melody sound continues sounding from your remote
LCD transceiver and “ ” indication flashes on the LCD screen.
2. Turn on the ignition switch; OR press the button to arm the system; OR press the
button to disarm the system, this outdoor driver paging function will exit.
S. DOME LIGHT CONVENIENCE DELAY & SUPERVISION:
The alarm has a unique feature that will turn on your vehicle dome light as following:
1. Upon disarming, the interior lights will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: Turning ON the ignition switch or arming the alarm will turn off the dome light.
T. IGNITION CONTROLLED POWER DOOR LOCKS: (See Feature II –3 Programming):
1. Turn the ignition switch on and close all the vehicle’s doors. After 3 seconds, the system will
automatically lock the central locking system.
2. Turn the ignition switch off. The system will automatically unlock the central locking system.

MEGA 2500 OPERATE
8
U. TRUNK RELEASE (Factory default setting) / CHANNEL 3 TIMER
CONTROL OUTPUT: (See Alarm Feature III –3 Programming):
Press and hold the button on transmitter for two seconds to remote control the trunk
release or other electric devices.
Channel 3 is user-programmable timer output. You may program the built-in timer to send
a ground signal for any time interval between 1 second and 2 minutes. For instance, this
timer output may be used to turn on the headlights, power windows, or sunroof.
Note: Factory default setting at 1-second pulse grounded for trunk release output.
V. CHANNEL 4 TIMER CONTROL OUTPUT: (See Alarm Feature III- 4
Programming):
Press the transmitter and buttons at the same time to active Channel 4 function.
Channel 4 is user-programmable timer output. You may program the built-in timer to send
a ground signal for any time interval between 1 second and 2 minutes. For instance, this
timer output may be used to turn on the headlight, power windows, or sunroof.
Note: Factory defaults setting at momentary output.
W. POWER ON MEMONRY:
This security system is equipped with circuitry that will allow the unit to remember its alarm state if the
power is lost and then reconnected.
LCD REMOTE TRANSCEIVER:
Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power
or such obstacles like tall buildings and so on, the transmission range may get shorter as the system
uses low output powered frequency.
A. BATTERY REPLACEMENT:
A 1.5V type AAA Alkaline battery powers the remote transceiver. When the power of the battery weakens,
a icon shall be displayed on the LCD screen. When the old battery is replaced with a new one, there
will be beep sounds indicating the power is up and the clock on the LCD screen returns to AM12:00 after
displaying all the icons. Correct the time by pressing for 3 seconds before using (See Timer Setting).
Note: Press the button two times when the battery compartment is empty and then insert the
new battery.
B. REMOTE LCD ICONS WITH FUNCTION:
Door Lock
Your vehicle doors are locked
Door Unlock
Your vehicle doors are unlocked and
the system is disarmed
Armed Mode
Your vehicle is in armed mode
Valet Mode
All the function shall be temporarily
on hold.
Remote Transmission
You are transmitting the signal to
control unit
In –Range Indicator
You are within the remote control
range.
Door Open Warning
Doors are illegally opened (Zone 3)
Trunk/Hood Trigger
Trunk or Hood is illegally opened
(Zone 2)
Shock Sensor Trigger
Trigger on Shock Sensor (Zone 4)
Warn Away trigger
Trigger on Shock Sensor (Zone 1)
Time Monitor
Alert Alarm
You have set morning call alarm

MEGA 2500 OPERATE
9
Count Down Timer
Reminder when time is up for
parking
Power Save Mode
Save the battery power
Vibration Mode
Remote Control vibrates when the
system is triggered
Button Lock
Disable the transmission function
temporarily
Driver paging
Someone is paging you in front of
your vehicle
Low Battery
You have to replace the battery of
remote control.
Ignition Trigger
Trigger on Ignition Switch (Zone 5)
Engine Running
Your vehicle's engine is running
A. PROGRAMMING OF THE LCD REMOTE TRANSMITTER:
Transmitter Button
Description
Operation
F(1 second)
LCD screen lamp turns on for
5 seconds.
Press and hold for 1 second
1 melody sound to confirm enters.
F(3 seconds)
Timer Programming Mode
Press and hold for 3 seconds
2-melody sounds to confirm enter.
F(5 seconds)
Power Save Mode
Press and hold for 5 seconds
1 melody sound to confirm enters.
F- F- F
Clear the Flash Icon and Melody Sound
on the LCD Screen Transmitter
Press within 3 seconds
F-(2-second)
Button Lock ( ) enable / disable
Press within 3 seconds
F-(2-second)
Melody / Vibration ( ) Mode
Press within 3 seconds
F-(2-second)
Program Count Down Timer ( )
(10-Minute / 20M / 30 M /1Hour /1.5H /
2.0H)
Press within 3 seconds cycling leave
the buttons starting countdown then
flashes
F-(2-second)
Enable / Disable Bi Sound (Bi) While
Pressing Button
1. Screen Lamp ON: Press and hold the Fbutton for one second, the melody will sound
and the LCD screen lamp will turn on for 5 seconds.
2. Power Save Mode: While in power save mode, the LCD remote transceiver uses “0”
current to save battery power.
Entry: Press & hold the Fbutton for 5 seconds. There will be one melody sound and the
icon will stay on the LCD screen to indicate entry of “power save mode”.
Exit: Press any button of the LCD remote transmitter to exit “Power Save Mode”.
3. Clear the Flash Icon and Melody Sound: Pressing the Fbutton 3 times within 3 seconds will clear the
flashing icon and melody sound on the LCD screen transceiver
4. Stop The Trigger Melody Sound: While triggering the alarm the LCD screen will alert user through
melody sound and flashing trigger icon. Press any button on the LCD remote transmitter to stop the
melody sound only.
5. Button Lock: Useful if you want to disable the transmission function of the remote
control temporarily to prevent from any inadvertent pressing of buttons by others. Press
the Fbutton first, within 3 seconds press and hold the ()button for 2 seconds to
activate or cancel the button lock function. The icon will be displayed on the LCD
screen to show the LCD remote transmitter is on “Button Lock”.
6. Vibration / Melody Mode:
Useful when you are in a noisy place and difficult to hear beep sounds from the remote
control. In this mode, the remote control vibrates itself if your security system is triggered.
Press the Fbutton first, within 3 seconds press and hold the ( ) button for 2
seconds to select the mode of vibration or melody, the icon will be displayed on the
LCD screen to show the LCD remote transceiver is on vibration mode.
7. Enable / Disable Bi Sound While Pressing Button:
There is a short “bi” sound while pressing the button of the LCD screen transceiver

MEGA 2500 OPERATE
10
If you want to mute the “bi” sound when you press a button, press the Fbutton first, within 3 seconds
press and hold the (Bi) button for 2 seconds to disable the “bi” sound.
8. Low Battery Indication:
When the power of the battery weakens, it has two short “bi” sounds and flash icon while pressing a
button on the LCD screen transceiver.
9. Set Up Fixed Count Down Timer:
1. Press the Fbutton first, within 3 seconds press and hold the () button for 2 seconds, the
LCD screen will show icon and timer (i.e. 0:10),
2. Press the () button again showing next order time on the screen (i.e. 0:20), press them again
(i.e. 0:30)…..and so on.
3. Leave the buttons starting countdown then icon flashes
Note: 1.Countdown period is fixed 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5 hours, and 2 hours.
2. When countdown timer showing 0:00 means to turn off the timer.
3. Press Fbutton for real time indication when the timer is counting down.
10. Out Of Range Indication:
The system will automatically check the range every 20 minutes after armed.
1. If user is within the range, the icon will display on the LCD screen.
2. If user is out of range, it has five short “bi” sounds and the icon will disappear on the LCD screen.
B. TIMER SETTING:
Transceiver Button
Description
Press Transceiver Button
1
Press & Hold the Fbutton
for 3 seconds
Timer Setting (Hour)
*Flash digit for adjusting
for –and for +
Press the Fbutton once
Time setting (Minute)
*Flash digit for adjusting
for –and for +
2
Press the Fbutton once
Alert Alarm Time Setting (Hour)
*Flash digit for adjusting
for –and for +
Press the Fbutton once
Alert Alarm Time Setting (Minute)
*Flash digit for adjusting
for –and for +
Press the Fbutton once
Alert Alarm Setting ON / OFF
for OFF and for ON
3
Press the Fbutton once
Count Down Timer Setting (Hour)
*Flash digit for adjusting
(Max.19 hours 59 minutes)
for –and for +
Press the Fbutton once
Count down Timer Setting (Minute)
*Flash digit for adjusting
for –and for +
Press the Fbutton once
Count down Timer Setting ON / OFF
for OFF and for ON
EXIT: Press and hold the Fbutton for 2 seconds or leave it for 10 seconds.
1. Timer Setting (Example 10:30 AM):
1. Press & hold the Fbutton for 3 seconds, with two-melody sound, the “Hours” digit flashes for adjusting.
2. Press the or button to decrease or increase the “Hour” digit until AM10:xx
3. Press the Fbutton once again then the “Minute” digit flashes for adjusting.
4. Press the or button to decrease or increase the “Minutes” digit until AM 10:30
5. Press the Fbutton for 2 seconds with one-melody sound to confirm exit the timer program mode.
2. Alert Alarm Timer Setting (Example 6:30 PM):
1. Press & hold the Fbutton for 3 seconds, with two-melody sound, “Hours” digit flashes for adjusting.
2. Press the Fbutton twice, the LCD screen will shows icon and “Hours” digit flashes for adjusting.
3. Press the or button to decrease or increase the “Hour” digit until PM 6:xx
4. Press the Fbutton once again then the “Minutes” digit flashes for adjusting.
5. Press the or button to decrease or increase the “Minutes” digit until PM 6:30
6. Press the Fbutton once again then icon flashes for alert alarm “ON / OFF” setting
7. Press the button to start the “Alert Alarm Timer”, and the “ON” icon will show on the LCD screen.
8. Press the button to stop “Alert Alarm Timer”, and “OFF” icon will show on LCD screen.
9. Press Fbutton for 2 seconds with one-melody sound to confirm exit the timer program mode.

MEGA 2500 OPERATE
11
3. Count Down Timer Setting (Example set countdown timer to 2:30):
1. Press & hold the Fbutton for 3 seconds, with two-melody sound, “Hours” digit flashes for adjusting.
2. Press the Fbutton 5 times, LCD screen will show icon and “Hours” digit is flashes for adjusting.
3. Press the or button to decrease or increase the “Hour” digit until 2:xx
4. Press the Fbutton once again then the “Minutes” digit flashes for adjusting.
5. Press the or button to decrease or increase the “Minute” digit until 2:30
6. Press the Fbutton once again then icon flashes for alert alarm “ON / OFF” setting
7. Press the button to start the countdown timer, and the “ON” icon will show on the LCD screen.
Press the button to stop the countdown timer, and the “OFF” icon will show on the LCD screen.
8. Press the Fbutton for 2 seconds with one-melody sound to confirm exit the timer program mode.
Note: Maximum is 19 hours.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.

MEGA 2500 OPERATE
12